Due to the controller limitation to keep the chip select low during the
bus idle time between the transfer, a dummy cs workaround was used when
this driver was first upstreamed to the u-boot based on linux kernel
driver. It basically picks the dummy cs as !actual_cs so typically dummy
cs is 1 when most of the case only cs 0 is used in the board design.
Then invert the polarity of both cs and tell the controller to start the
transfers using dummy cs. Assuming both cs are active low before the
inversion, effectively this keeps dummy cs high and actual cs low during
the transfer and workaround the issue.
This workaround requires that dummy cs 1 pin to is set to SPI chip
selection function in the pinmux when the transfer clock is above 25MHz.
The old chips likely have default pinmux set to chip select on the dummy
cs pin so it works but this is not case for the new Broadband BCA chips
and this workaround stop working. This is specifically an issue to
support SPI NAND and SPI NOR flash because these flash devices can
typically run at or above 100MHz.
This patch utilizes the prepend feature of the controller to combine the
multiple transfers in the same message to a single transfer when
possible. This way there is no need to keep clock low between transfers
and solve the issue without any pinmux requirement.
Multiple transfers within a SPI message may be combined into one
transfer if the following are all true:
* One or more half duplex write transfer in single bit mode
* Optional full duplex read/write at the end
* No delay and cs_change between transfers
Most of the SPI device meets this requirements such as SPI NOR, SPI NAND
flash, Broadcom SPI voice card and etc. So this change switches to the
prepend mode as the default mode. For any SPI message that does not meet
the above requirement, we switch to original dummy cs mode but limit the
clock rate to the safe 25MHz.
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-12-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
New compatible string brcm,bcmbca-hsspi-v1.0 is introduced based on
dts document brcm,bcm63xx-hsspi.yaml. Add it to the driver to support
this new binding.
Port from linux patch:
Link: https://lore.kernel.org/r/20230207065826.285013-6-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the driver always sets the controller to dual data bit mode
for both tx and rx data in the profile mode control register even for
single data bit transfer. Luckily the opcode is set correctly according
to SPI transfer data bit width so it does not actually cause issues.
This change fixes the problem by setting tx and rx data bit mode field
correctly according to the actual SPI transfer tx and rx data bit width.
Fixes: 29cc4368ad ("dm: spi: add BCM63xx HSSPI driver")
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-11-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
ARCH_BCMBCA was introduced to cover individual Broadcom broadband SoC
for common features and IP blocks. Use this config instead of each chip
config as the Kconfig dependency for Broadcom HSSPI driver.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for an optional external chip-select gpio.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Remove the platform data header because its content is only used by the
driver.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Rename the flush function into pl022_spi_flush to avoid conflicting
types with previous declaration of the function in stdio.h header.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Align the compatible property with the kernel device tree binding [1]
by removing the '-spi' suffix.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/spi/spi-pl022.yaml
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The CN9130 SoC (an ARMADA 8K type) has both a NAND Flash Controller and
a generic local bus controller (Device Bus Controller) that share common
pins.
With a board design that incorporates both a NAND flash and uses
the Device Bus (in our case for an SRAM) accessing the Device Bus device
fails unless the NfArbiterEn bit is set. Setting the bit enables
arbitration between the Device Bus and the NAND flash.
Since there is no obvious downside in enabling this for designs that
don't require arbitration, we always enable it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The NAND flash controller (NFC) on the AC5/AC5X SoC is the same as
the NFC used on other Marvell SoCs. It does have the additional
restriction of only supporting SDR timing modes up to 3.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The NF_CLK for the AC5 SoC runs at 400MHz. There's no strapping
or gating require so just add a mvebu_get_nand_clock() that
returns this value.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The AC5/AC5X SoC has a NAND flash controller. Add this to the
SoC device tree.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Update the Thecus N2350 DTS to conform with latest device-tree binding
and styles.
- Correct typo in mdio node.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Add basic config for Sipeed Lichee PI 4A board which make it capable of
booting into serial console.
Reviewed-by: Wei Fu <wefu@redhat.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's
TH1520 SoC, only minimal device tree and serial console are enabled,
so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by: Wei Fu <wefu@redhat.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
As the RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, we rename SiFive CLINT to RISC-V
ALINT in the source tree to be future-proof.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This RISC-V ACLINT specification [1] defines a set of memory mapped
devices which provide inter-processor interrupts (IPI) and timer
functionalities for each HART on a multi-HART RISC-V platform.
The RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, however the device tree binding
is a new one. This change updates the sifive clint ipi driver to
support ACLINT mswi device, by checking the per-driver data field of
the ACLINT mtimer driver to determine whether a syscon based approach
needs to be taken to get the base address of the ACLINT mswi device.
[1] https://github.com/riscv/riscv-aclint/blob/main/riscv-aclint.adoc
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This RISC-V ACLINT specification [1] defines a set of memory mapped
devices which provide inter-processor interrupts (IPI) and timer
functionalities for each HART on a multi-HART RISC-V platform.
The RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, however the device tree binding
is a new one. This change updates the sifive clint timer driver to
support ACLINT mtimer device, using a per-driver data field to hold
the mtimer offset to the base address encoded in the mtimer node.
[1] https://github.com/riscv/riscv-aclint/blob/main/riscv-aclint.adoc
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
The main difference between StarFive VisionFive 2 1.2A and 1.3B is gmac.
You can read the PCB version of the current board by
get_pcb_revision_from_eeprom(), and then dynamically configure the
difference of gmac in spl_perform_fixups() according to different PCB
versions, so that one DT and one defconfig can support both 1.2A and
1.3B versions, which is more user-friendly.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
StarFive VisionFive 2 has two versions, 1.2A and 1.3B, each version of
DDR capacity includes 2G/4G/8G, a DT can not support multiple
capacities, so the capacity size information is recorded to EEPROM, when
DDR initialization required capacity size information is read from
EEPROM.
If there is no information in EEPROM, it is initialized with the default
size defined in DT.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enabled ID_EEPROM and I2C configuration for StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-By: Leo Yu-Chi Linag <ycliang@andestech.com>
Add support "atmel,24c04" eeprom for StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable DWC_ETH_QOS and PHY_MOTORCOMM configuration to support ethernet
function for StarFive VisionFive 2 board,including versions 1.2A and
1.3B.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The defconfig file name for StarFive VisionFive2 has been changed, and
the documentation description has also changed.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The difference between 1.2A and 1.3B is dynamically configured according
to the PCB version, and there is no difference on the board device tree,
so the same DT file can be used.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add ethernet device tree node to support StarFive ethernet driver for
the JH7110 RISC-V SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The StarFive ETHQOS hardware has its own clock and reset,so add a
corresponding glue driver to configure them.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have
verified the driver on StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When tagging and releasing v2023.07 I forgot to drop the -rc6 tag. For
regular use, I've made a v2023.07.01 tag, but for here we can just drop
the -rc6 tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since U-Boot builds HTML documentation, migrate the contents
of the README file to an rst file which can generate the
proper outputs.
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of cluttering up a header file with a bunch of defines,
move the default environmental variables to a file called
imx8mn_beacon.env and reference it from the defconfigs.
Signed-off-by: Adam Ford <aford173@gmail.com>
Since U-Boot builds HTML documentation, migrate the contents
of the README file to an rst file which can generate the
proper outputs.
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of cluttering up a header file with a bunch of defines,
move the default environmental variables to a file called
imx8mm_beacon.env and reference it from the defconfig.
Signed-off-by: Adam Ford <aford173@gmail.com>
While testing the ethernet interface on a Variscite symphony carrier
board using an imx8mn SOM with an onboard ADIN1300 PHY (EC hardware
configuration), the ethernet PHY is not detected.
The ADIN1300 datasheet indicate that the "Management interface
active (t4)" state is reached at most 5ms after the reset signal is
deasserted.
The device tree in Variscite custom git repository uses the following
property:
phy-reset-post-delay = <20>;
Add a new MDIO property 'reset-deassert-us' of 20ms to have the same
delay inside the ethphy node. Adding this property fixes the problem
with the PHY detection.
Note that this SOM can also have an Atheros AR8033 PHY. In this case,
a 1ms deassert delay is sufficient. Add a comment to that effect.
Fixes: c4c1ed68c1 ("imx8mn_var_som: Add support for Variscite
VAR-SOM-MX8M-NANO board")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Select DM_ETH_PHY so that the reset-gpios property of the ethphy node
can be used.
Also select DM_PCA953X, which is needed for resetting the
ethernet PHY on the carrier board via the PCA9534 I/O expander.
Commit 4e5114daf9 ("imx8mn: synchronise device tree with linux") did
synchronise device tree with linux, which in effect removed obsolete
PHY reset properties and replaced them with new mdio DM
properties. But the commit didn't activate DM_ETH_PHY or DM_PCA953X.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Enable support to read and display configuration/manufacturing infos
from 4Kbit EEPROM located on SOM board.
Note: CONFIG_DISPLAY_BOARDINFO is automatically selected for ARM arch.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Getting
Found /vpu_g1@38300000 node
Modify /vpu_g1@38300000:status disabled
Found /vpu_g2@38310000 node
Modify /vpu_g2@38310000:status disabled
etc. on the console on every boot is needlessly verbose. Demote the
"Found ..." lines to debug(), which is consistent with other instances
in soc.c.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The single binary version of u-boot for XEA board is used to debrick and
factory programming.
The produced u-boot.sb is a single file, which allows having fully
operational u-boot prompt loaded with imx287 ROM.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The XEA board now supports the DM_SERIAL feature in u-boot.
The SPL is using the SPL_OF_PLATDATA - i.e. NOT SPL_DM_SERIAL to
reduce the overall size of the SPL binary.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
