Commit graph

9 commits

Author SHA1 Message Date
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Tom Rini
a8992e788a env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND check
We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it.  We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result.  The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED.  This seems like the most likely use, historically, of
the variable, but it was not used.  Add logic to check for this now.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-11-20 18:31:24 -05:00
Tom Rini
cb6617a77f defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENT
Move this symbol to Kconfig.  As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-12 11:08:00 -05:00
Horatiu Vultur
b158e56f34 configs: vcoreiii: Change CONFIG_ENV_SIZE
Shrink the environment size for 3 reasons:

 - reading the environment it is slow, therefore having a smaller env
   improves the speed.
 - usually in the environment there are only few variables, therefore
   the enviromnent is almost empty.
 - because the same image can run on different boards which may have
   different flashes with different page sizes, the CONFIG_ENV_SECT_SIZE
   can't be change, it is set to least common multiple of the page sizes.

Adding this change improves the boot time. Before update for reading the
entire environment it took ~850 msec, after the change it takes ~40 msecs.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12 17:32:51 +02:00
Horatiu Vultur
5e1d417bec net: Add MSCC Jaguar2 network driver.
Add network driver for Microsemi Ethernet switch.
It is present on Jaguar2 SoCs.

Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12 17:32:51 +02:00
Patrick Delaunay
abe66b1b5d Convert CONFIG_ENV_SPI_* to Kconfig
This converts the following to Kconfig:
  CONFIG_ENV_SPI_BUS
  CONFIG_ENV_SPI_CS
  CONFIG_ENV_SPI_MAX_HZ
  CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:59 -04:00
Horatiu Vultur
1895b87e84 MSCC: Add support for Serval SoC family.
As Ocelot, Servalt, Luton and Jaguar2, this family of SoCs are
found in Microsemi Switches solution.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-01-23 18:28:09 +01:00
Lars Povlsen
e9f1492bca mips: mscc: luton+ocelot: Remove board config options, do probing
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.

Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.

Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
2019-01-16 13:56:43 +01:00
Gregory CLEMENT
6787c1ece0 MSCC: add board support for the Ocelots based evaluation boards
Adding the support for 2 boards sharing common code for Ocelot chip:
PCB120 and PCB123

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
2018-12-19 15:23:01 +01:00