flash_get_size() will get the flash size from the device itself and go
through all erase regions to read protection status. However, the device
mappable region (eg: devicetree reg property) might be lower than the
device full size which means that the above cycle will result in a data
bus exception. This change fixes it by reading the 'addr_size' during
probe() and also use that as one possible upper limit.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
The mail ids of all the current Xilinx users are to be mapped to AMD
following the merger with AMD. The mailmap file is updated accordingly.
The ids of Marek Behún and Michal Simek are taken as reference.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230426060104.10412-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The mailmap ids are not arranged in the dictionary order. So, sort the
mailmap ids in the dictionary order.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230426060104.10412-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This reverts commit e097847286. The
commit wrongly divides the dummy bytes by dummy bus width to calculate
the dummy bytes. The framework already converts the dummy cycles to the
number of bytes and the controller use the SPI flash command to
determine the dummy cycles via the address width.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230427065355.7413-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Some of the Kria SOM and ZynqMP boards are using Analog Devices ethernet
phy. So, enable CONFIG_PHY_ADIN for all ZynqMP platforms.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230420085645.21260-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In current implementation, applications can execute only on R5 core 0.
The boot address for R5 core 1 is not supplied. Pass TCM address for
R5 core 1 based on the argument to fix the issue.
Remove incomplete comment.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/da865717d26648ab7a84345ca8749712efdddee5.1680699999.git.michal.simek@amd.com
The "zynqmp tcminit split" command should halt both cores and not just RPU1
when configuring the TCM memory for split mode.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/20230323082506.31576-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- Assorted bootstd fixes and cleanups. This should fix problems with
Debian, and make script-based distributions work when BOOTMETH_DISTRO
is enabled now (as BOOTMETH_DISTRO was renamed and then reintroduced).
We cannot be sure what bootmeth a distro will need to use. Add a new
BOOTMETH_DISTRO option which collects these together. Select this from
BOOTSTD_DEFAULTS so that it is clear what is needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make BOOTMETH_EFILOADER depend on EFI_LOADER, select if EFI_LOADER]
Signed-off-by: Tom Rini <trini@konsulko.com>
We use the terms 'distro' to mean extlinux but they are not really the
same. 'Distro' could refer to any method of booting a distribution,
whereas extlinux is a particular method.
Also we sometimes use syslinux, but it is better to use the same term in
all cases.
Rename distro to syslinux and also update bootstd uses of syslinux to use
extlinux instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a few cases the error handling is not quite right. Make sure we
return the actual error in distro_efi_read_bootflow_file() rather than
-EINVAL. Return -IO when a file cannot be read. Also show the error name
if available.
This does not change operation, but does make it easier to diagnose
problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
The patch to relax flag requirements was not accepted[1], so we still have
to have separate bootcommands depending on CMD_BOOTFLOW_FULL.
The previous attempt at this did not work, since it used the wrong name
for the options.
Fix this and change the message to mention BOOTSTD_FULL since this affects
not just the flags, but all functionality, so is more likely what the user
wants.
Drop the useless condition on CMD_BOOTFLOW_FULL while we are here.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20230329071655.1959513-2-sjg@chromium.org/
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: a91492b6e9 ("bootstd: Provide a default command")
Armbian uses a script which needs the HUSH parser. It is likely that
other distros will do the same. Enable it by default, just in case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
This causes crashes on some boards, e.g. rockpro64. In any case, we
should not do it.
Check the usb_started flag to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Tom Rini <trini@konsulko.com>
This should be declared in a header file so that type-checking works
correctly.
Add a single declaration to usb.h and remove the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
If there is no partition numbered 1, we decide that there are no
partitions at all. That may not be correct, since at least one Debian
installed has just a single partition numbered 2.
Continue searching up to partition 3, just in case.
Signed-off-by: Simon Glass <sjg@chromium.org>
* When called from efi_dp_from_name() we miss to append the filename
for non-block devices.
* expand_media_path() could be simplified by using efi_dp_from_file to
prepend the device path of the boot device.
This can be avoided by passing a device path to efi_dp_from_file() instead
of a block device descriptor and a partition number.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* Improve variable name usage: Use pos instead of buf to indicate the
current position in a buffer.
* Avoid double assignment in a single code line.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
efi_dp_from_name() has duplicate code to replace slash by backslash.
path_to_uefi() called by efi_dp_from_file() already does this.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
According to our coding style guide #ifdef should be avoided.
Use IS_ENABLED() instead.
Sort string comparisons alphabetically.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Executing an EFI binary fails for files loaded via semihosting.
Construct a dummy device path for EFI binaries loaded via semihosting.
A future complete solution may include the creation of a handle with a
simple file system protocol.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tom reports that when building with clang we see this warning:
field guid within 'struct efi_hii_keyboard_layout' is less aligned than 'efi_guid_t' and is usually due to 'struct efi_hii_keyboard_layout' being packed, which can lead to unaligned accesses [-Wunaligned-access]
This happens because 'struct efi_hii_keyboard_layout' is defined as
packed and thus has 1-byte alignment but efi_guid_t is a type that
requires greater alignment than that.
However the EFI spec describes the EFI_GUID as
"128-bit buffer containing a unique identifier value.
Unless otherwise specified"
So convert the efi_guid_t -> u8 b[16] here and skip the alignment
requirements. Since the struct is packed to begin with, it makes no
difference on the final memory layout.
Suggested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Symbol CONFIG_EFI_SETUP_EARLY does not exist anymore.
CONFIG_FWU_MULTI_BANK_UPDATE without CONFIG_FWU_MDATA results in
lib/fwu_updates/fwu.c:49: undefined reference to `fwu_get_mdata'
Fixes: 8679405241 ("FWU: Add support for the FWU Multi Bank Update feature")
Fixes: 023d9c9393 ("efi_loader: remove CONFIG_EFI_SETUP_EARLY")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Since U-Boot supports more RSA/SHA variants, as well as ECDSA, remove
these items from the TODO list.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
U-Boot supports more hash and verification algorithms these days.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
As a starting point, list all currently supported Renesas boards.
For the RZ/N1 board, add details about booting and flashing.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Renesas RZ/N1 devices contain BootROM code that loads a custom SPKG
image from QSPI, NAND or USB DFU. Support this format in mkimage tool.
SPKGs can optionally be signed, however creation of signed SPKG is not
currently supported.
Example of how to use it:
tools/mkimage -n board/schneider/rzn1-snarc/spkgimage.cfg \
-T spkgimage -a 0x20040000 -e 0x20040000 \
-d u-boot.bin u-boot.bin.spkg
The config file (spkgimage.cfg in this example) contains additional
parameters such as NAND ECC settings.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The RZ/N1 is a family of SoC devices from Renesas, featuring:
* ARM Cortex-A7 CPU (single/dual core) and/or Cortex-M3
* Integrated SRAM up to 6MB
* Integrated gigabit ethernet switch
* Optional DDR2/3 controller
* I2C, SPI, UART, NAND, QSPI, SDIO, USB, CAN, RTC, LCD
Add basic support for this family, modeled on the existing RZA1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This is taken directly from Linux kernel 6.3
(commit 457391b0380335d5e9a5babdec90ac53928b23b4)
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Driver for Cadence EDAC DDR controller, as found in the Renesas RZ/N1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Pinctrl/pinconf driver for Renesas RZ/N1 (R906G032) SoC.
This is quite rudimentary right now, and only supports applying a
default pin configuration as specified by the device tree.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Clock driver for the Renesas RZ/N1 SoC family. This is based on
Linux kernel 6.2.y drivers/clk/renesas/r9a06g032-clocks.c as found in
commit 02693e11611e ("clk: renesas: r9a06g032: Repair grave increment error"),
with the following additional patch series applied:
https://lore.kernel.org/linux-renesas-soc/20230301215520.828455-1-ralph.siemsen@linaro.org/
Notable difference: this version avoids allocating a 'struct clk'
for each clock source, as this is problematic before relocation.
Instead, it uses the same approach as existing Renesas R-Car Gen2/3
clock drivers, using a temporary structure filled on-the-fly.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add new CONFIG_CLK_RCAR to control compilation of shared code for R-Car
clock drivers (renesas-cpg-mssr.c). Enable this for R-Car Gen2 and 3.
This is necessary so that CONFIG_CLK_RENESAS can be enabled, allowing
recursion into the drivers/clk/reneasas directory, without bringing in
the R-Car support code. The support code contains platform specific
access (TMU_BASE) which is not needed on other Renesas devices such as
RZ/N1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit 2564fce7ee ("sunxi: move Cortex SMPEN setting into start.S")
added SPL_ARMV7_SET_CORTEX_SMPEN to enable setting SMP bit. For
platforms not using SPL boot, add the corresponding non-SPL config,
so that CONFIG_IS_ENABLED(ARMV7_SET_CORTEX_SMPEN) works as expected.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
