Renamed dm "drivers" subcommand to "compat" (as it listed
compatibility strings) and prevent it from segfaulting when
drivers have no of_match populated.
Added a new "drivers" subcommand to dump a list of all known DM
drivers and for each, their uclass id, uclass driver and names of
attached devices.
Added a new "static" subcommand to dump a list of DM drivers with
statically defined platform data.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added command "fstypes" to list supported/included filesystems.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Limit to sandbox]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a subcommand "types" to the part command, which lists the supported
partition table types.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl8EgGEACgkQ4rK92eCq
k3V7mwf+N5Iq6CbUPP11mFiNgAFZ5+hcn6gBTWvbjnd+oaIp15hiQrUNusGNFxXe
oyM4fvm12tjuWFlA0U6VtiLhuVQB1Yte048oX+edDCCLGwxkp6cKBHtCaGT14XvY
ow60XInv/dlrINumf8isy+5QlLgT1Cb7aGZN1qRHsUtnHB/IC836KO+hukGRUvk3
Lqz+FbHqitKnL+CIboC2+YzXqG6ZXdixFZVVPmTVd34C8hQOdkExJ//uR/lH/s6f
vjaecs7HpIuKRpKpt5WcoLzTLd1hstqNNhmTbBHmVo+EqIjMkpISUwDpDJNU5pki
BPbdG9VXqb46JLaTtPT+U4gX4yJ3Bw==
=jQCC
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200707' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- arch and board update for stm32mp15:
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl8DHgAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyAdDCACFX01IPRmdkNEYrJf0
YfhQPAPZ/5EyHBv36ePl93CbIRnJPpnrGbBXe8+/Jdcq7l6EkJh2cuO+t9axXner
m0kH35LzLiR9Olz6q5Su0InPWpnDtXxtIczK5v7ZHBeMZ2so763e7SQ2VIMyJJb/
VT6hilqJK6+W1c2X1wmzxyh/nnv/bDBz97cavJN1EKw1arYr8jh/8/tpABk5msDm
J6Z5WsS/CYk7cj6hX7dSNRfqcKsjl/gCYjnVssfgaP1sH+NX0mtS8C6zchNILmpB
2T/dKnpYBBAWTD5fGNVKxKphAuZgQHw51AJhkOnYDrMKisifFC0ssvxkh+nvwyTm
1w4R
=1YzJ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.10 cycle
ARM Architecture reference manual clearly states that PE pipeline
should be flushed after changes to some system registers. Refer to
paragraph "B2.3.5 Memory Barriers" at page B2-92 of "Arm Architecture
Reference Manual ARMv8 for ARMv8-A Architecture Profile" (ARM DDI
0487B.a).
Failing to issue instruction synchronization barrier can lead to
spurious errors, like synchronous exception when accessing FPU
registers. This is very prominent on CPUs with long instruction
pipeline, like ARM Cortex A72.
This change fixes the following U-Boot panic:
"Synchronous Abort" handler, esr 0x1fe00000
elr: 00000000800948cc lr : 0000000080091e04
x0 : 00000000801ffdc8 x1 : 00000000000000c8
x2 : 00000000800979d4 x3 : 00000000801ffc60
x4 : 00000000801ffd40 x5 : ffffff80ffffffd8
x6 : 00000000801ffd70 x7 : 00000000801ffd70
x8 : 000000000000000a x9 : 0000000000000000
x10: 0000000000000044 x11: 0000000000000000
x12: 0000000000000000 x13: 0000000000000000
x14: 0000000000000000 x15: 0000000000000000
x16: 000000008008b2e0 x17: 0000000000000000
x18: 00000000801ffec0 x19: 00000000800957b0
x20: 00000000000000c8 x21: 00000000801ffdc8
x22: 000000008009909e x23: 0000000000000000
x24: 0000000000000000 x25: 0000000000000000
x26: 0000000000000000 x27: 0000000000000000
x28: 0000000000000000 x29: 00000000801ffc50
Code: a94417e4 a90217e4 a9051fe6 a90617e4 (3d801fe0)
While executing instruction
str q0, [sp, #112]
in vsnprintf() prologue. This panic was observed only on Cortex A72 so
far.
This patch places ISBs on other strategic places as well.
Also, this probably is the right fix for the issue workarounded in the
commit 45f41c134b ("ARM: uniphier: add weird workaround code for LD20")
Reported-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Suggested-by: Julien Grall <julien.grall.oss@gmail.com>
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
CC: Tom Rini <trini@konsulko.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Julien Grall <julien@xen.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add size and addr parameter to test "All" to override the default
value (4kB and STM32_DDR_BASE) used in tests with these optional
parameters: [size] or [addr].
When other optional parameters are present before [addr],
they are replaced by default value:
- [loop] = "1"
- [pattern] = "-" (new: force default pattern)
Example to use:
DDR>test 0 1 0x20000
DDR>test 0 1 0x1000000 0xD0000000
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The test 4 = "AddressBus [size] [addr]" without parameter
detects alias for any address bit only when:
- size = real size of DDR
- addr = start of DDR = 0xC0000000
These value must be the default value when parameters are absent.
This patch sets bufsize to STM32_DDR_SIZE and get_bufsize() selects
the correct value for bufsize when this parameter is absent =
full size of the DDDR
On EV1 board :
DDR> test 4
running at 0xC0000000 length 0x40000000
On DK2 board
DDR> test 4
running at 0xC0000000 length 0x20000000
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a parameter addr in test FrequencySelectivePattern to select
the base address used to execute the tests.
Default value (when the parameter is absent) is STM32_DDR_BASE,
selected in get_addr() function.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add protection on minimum value for result of get_bufsize
and check the alignment of buffer size: only multiple min_size
is allowed; only 4 bytes alignment was checked previously
(value & 0x3).
For example the "Random" test raises an issue when size is not 8 bytes
aligned because address for buffer = address + size / 2 is not word
aligned.
This patch avoid test error for unsupported size value.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate CMD_NVEDIT_INFO and use the new command "env info -d -p -q"
to automatically save the environment on first boot.
This patch allows to remove the env_default variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use the define ENV_IS_IN_DEVICE to test if one the
CONFIG_ENV_IS_IN_... is defined and correct the detection of
persistent storage support in the command "env info"
if CONFIG_ENV_IS_NOWHERE is activated.
Since commit 60d5ed2593c9 ("env: allow ENV_IS_NOWHERE with
other storage target") test CONFIG_ENV_IS_NOWHERE is not
enough; see also commit 953db29a1e9c6 ("env: enable saveenv
command when one CONFIG_ENV_IS_IN is activated").
This patch avoids issue for this command in stm32mp1 platform.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch update the current gpio hog implementation with
the new API gpio_hog_probe_all() activated with CONFIG_GPIO_HOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Migrate the ST Microelectronics STUSB160X Type-C controller code in
a generic I2C driver in st/common, based on Linux one in :
drivers/usb/typec/stusb160x.c
This patch simplifies the stm32mp1 board code and allows to reuse
this STUSB160X driver in other boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In the boot command used in ST boards, bootcmd_stm32mp, only support
the SD card as second stage, where is found the bootfs with DISTRO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As debugger must be totally closed on Sec closed chip,
the DBGMCU_IDC register is no more accessible (self
hosted debug is disabled with OTP).
This patch adds a function bsec_dbgswenable() to check
if the DBGMCU registers are available before to access them:
BSEC_DENABLE.DBGSWENABLE = self hosted debug status.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add "Device Name" in iproduct during DFU USB enumeration
to have this information in STM32CubeProgrammer trace
(this tools is compatible with @Name since v2.3)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
With TEE 3.7.0, the partition teed (OP-TEE pageable
code and data) need to increase up to 512KB in NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate the command env erase to reset the environment with the command:
> env erase
it is simpler than:
> env default -a
> env save
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
There maybe an overshoot:
- when disabling, then re-enabling vrefbuf too quickly
- or upon platform reset as external capacitor maybe slow
discharging (VREFBUF is HiZ at reset by default).
VREFBUF is used by ADC/DAC on some boards. An overshoot on the reference
voltage make the conversions inaccurate for a short period of time. So:
- Don't put the VREFBUF in HiZ when disabling, to force an active
discharge.
- Enforce a 1ms OFF/ON delay, also upon reset
Penalty is a 1ms delay is applied (even for a cold boot), when enabling
VREFBUF.
Fixes: 93cf0ae775 ("power: regulator: Add support for stm32-vrefbuf")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As kernel v5.6 have a solution since so we will be able to enable
the watchdog at boot time. It is reloaded by the watchdog
framework (if CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is set) and
until the userspace watchdog daemon takes over control.
Need presence of kernel patch 85fdc63fe256 ("drivers: watchdog:
stm32_iwdg: set WDOG_HW_RUNNING at probe") integrated in v5.6-rc1.
This patch revert the previous commit ca351e705a ("stm32mp1:
deactivate WATCHDOG in defconfig").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add information on pin configuration used for pinmux command:
- bias configuration for output (disable, pull up, pull down)
- otype for input (open drain or push pull)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add information on pin configuration used for pinmux command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of ops get_dir_flags() to read dir flags from
STMFX registers.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the helper functions stmfx_read_reg() and stmfx_write_reg() to avoid
duplicated code for access to stmfx's register with mask.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Rename the two function used to change the pin configuration
from stmfx_pinctrl_.. stmfx_conf_... to clarify the function usage.
No functional change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the functions stmfx_pinctrl_set_pupd and stmfx_pinctrl_set_type;
they can be used by the new ops get_dir_flags and set_dir_flags introduced
by next patch.
No functional change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add ops get_dir_flags() to read dir flags from GPIO registers.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch updates the current gpio hog implementation and uses
the new API gpio_hog_probe_all(), activated with CONFIG_GPIO_HOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch activates the new configuration CONFIG_GPIO_HOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the debug function board_debug_uart_init in spl.c
as the debug_uart_init() function is called in arch_cpu_init()
only for SPL and remove the board.c file.
For TFABOOT, the UART TX pin configuration is done in TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch allows to switch the CPU frequency to 800MHz on the
ST Microelectronics board (DK1/DK2 and EV1) or dh electronics SOM
using the STM32MP15x SOC and when it is supported by the HW
(for STM32MP15xD and STM32MP15xF).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
For board using STPMIC1, the vddcore is provided by BUCK1 of STPMIC1
and need to be updated for 800MHz support and only after the clock
tree initialization.
The VDDCORE voltage value is provided by clock driver, saved in global
variable opp_voltage_mv and udpated in SPL board_early_init_f(),
just after clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
is absent)
- Check if debug is enabled to program PMIC according to the bit
This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.
CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a weak functions to save the vddcore voltage value provided
in the OPP node when the clock tree is initialized.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The PLL1 node (st,pll1) is optional in device tree, the max supported
frequency define in OPP node is used when the node is absent.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move function board_ddr_power_init() in a new file stpmic1 in
board/st/common to avoid duplicated code in each board using
stpmic1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This commit adds cpufreq support on stm32mp15x SOC. STM32 cpufreq uses
operating points V2 bindings (no legacy). Nvmem cells have to be used to
know the chip version and then which OPPs are available. Note that STM32
cpufreq driver is mainly based on "cpufreq-dt" driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the bsec driver in SPL, as it is needed by SOC part number detection
to found the supported OPP.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update the compatible associated with the STM32 MPU glue
in the DWC ethernet driver.
The supported compatible is the specific "st,stm32mp1-dwmac"
as indicated in Linux binding
Documentation/devicetree/bindings/net/stm32-dwmac.txt
and not the "snps,dwmac-4.20a" only used to the select IP
version.
This glue is implemented in Linux kernel in:
drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
For information in stm32mp151.dtsi, the 2 compatibles are
supported:
ethernet0: ethernet@5800a000 {
compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
...
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
According to the FAT specification it is valid to have files with an
attribute value of 0x0. This fixes a regression where different U-Boot
versions are showing different amount of files on the same storage
device. With this change U-Boot shows the same number of files and folders
as Linux and Windows.
Fixes: 39606d462c ("fs: fat: handle deleted directory entries correctly")
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
While relocating FDT we reserve some memory for the new FDT and
set the size of the FDT with that respect. But FDT may be placed
at the end of the RAM leading to memory access beyond it.
Fix this by copying exact FDT size bytes, not the reserved size.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As part of merging the next branch in to master, the sifive_fu540 will
fail to link:
riscv64-linux-ld.bfd: lib/built-in.o: in function `panic_finish':
lib/panic.c:28: undefined reference to `do_reset'
make[2]: *** [spl/u-boot-spl] Error 1
make[1]: *** [spl/u-boot-spl] Error 2
make: *** [sub-make] Error 2
And while the "fix the build" option of enabling CONFIG_SPL_SYSRESET may
solve the issue, it is unclear that it is the correct path exactly. For
the moment, I am reverting this commit and take a "revert the revert"
and proper fix as soon as it's available.
This reverts commit cdae446461.
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch restores CONFIG_VIDCONSOLE_AS_LCD as boolean
and introduce a separate sting as CONFIG_VIDCONSOLE_AS_NAME
to search this string in stdout used as videoconsole.
This patch avoid issue with board defconfig or code expecting
CONFIG_VIDCONSOLE_AS_LCD as boolean.
Fixes: 22b897a123 ("video: extend stdout video console work-around for 'vga'")
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This series comprises error corrections for the UEFI subsystem:
* correct consideration of timestamps for variable authentication
* correct collection of data regions for code authentication
* correct unit tests to test loading dbx
* enable FAT_WRITE as required by the UEFI spec
The boot manager uses log functions instead of printf() and debug().
The UEFI intialization state is exported.
-----BEGIN PGP SIGNATURE-----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=wwI2
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for UEFI sub-system for efi-2020-10-rc1
This series comprises error corrections for the UEFI subsystem:
* correct consideration of timestamps for variable authentication
* correct collection of data regions for code authentication
* correct unit tests to test loading dbx
* enable FAT_WRITE as required by the UEFI spec
The boot manager uses log functions instead of printf() and debug().
The UEFI intialization state is exported.
