This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Williams <steve@icarus.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We don't want that CONSOLE is redirected to LCD upon init, we rather prefer
that console is still on the serial line.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
When Beagle X15 is connected to Gigabit switch, it takes
more time to finish auto-negotiation than on a 10/100 switch.
The default 4 second limit times-out more often than not. This is
observed when testing with a D-Link DGS-1008A desktop switch.
Increase the auto-negotiation time-out for Beagle-X15 to handle
this case.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
RX51 has a secure logic which uses different parameters compared to
traditional implementation. So, make the generic secure acr write
over-ride-able by board file and refactor rx51 code to use this.
While at it, enable the OMAP3 specific errata code for 454179, 430973,
621766.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the OMAP3 specific errata code for 454179, 430973, 621766
and while at it, remove legacy non-revision checked errata logic.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch enables the workaround for ARM errata 798870 for OMAP5 /
DRA7 which says "If back-to-back speculative cache line fills (fill
A and fill B) are issued from the L1 data cache of a CPU to the
L2 cache, the second request (fill B) is then cancelled, and the
second request would have detected a hazard against a recent write or
eviction (write B) to the same cache line as fill B then the L2 logic
might deadlock."
An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced
here as well.
Signed-off-by: Praveen Rao <prao@ti.com>
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is in preperation of using generic cross OMAP code.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The purpose of this build target is to do SPL over USB RNDIS. We remove
YMODEM, MMC and NAND (and re-set ENV to be built-in) as when those are needed
we can use the other build targets. This brings us well under size limit again.
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix a typo in board/sunxi/Kconfig which caused VIDEO_LCD_PANEL_I2C to be
enabled on all sunxi boards. Also fix a compile error which shows up once
VIDEO_LCD_PANEL_I2C is actually disabled on most boards as it should be.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While the Freescale ARMv8 board LS2085A will enter U-Boot both
on a master and a secondary (slave) CPU, this is not the common
behaviour on ARMv8 platforms. The norm is that U-Boot is entered
from the master CPU only, while the other CPUs are kept in
WFI (wait for interrupt) state.
The code determining which CPU we are running on is using the
MPIDR register, but the definition of that register varies with
platform to some extent, and handling multi-cluster platforms
(such as the Juno) will become cumbersome. It is better to only
enable the multiple entry code on machines that actually need
it and disable it by default.
Make the single entry default and add a special
ARMV8_MULTIENTRY KConfig option to be used by the
platforms that need multientry and set it for the LS2085A.
Delete all use of the CPU_RELEASE_ADDR from the Vexpress64
boards as it is just totally unused and misleading, and
make it conditional in the generic start.S code.
This makes the Juno platform start U-Boot properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The dfu mmc file buffer, which was static, now is allocated
by memalign(), so the malloc pool len should be also increased.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Tom Warren <twarren.nvidia@gmail.com>
The dfu mmc file buffer, which was static, now is allocated
by memalign(), so the malloc pool len should be also increased.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
The dfu mmc file buffer, which was static, now is allocated
by memalign(), so the malloc pool len should be also increased.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Michal Simek <michal.simek@xilinx.com>
This commit enables the following configs:
- CONFIG_USE_ARCH_MEMCPY
- CONFIG_USE_ARCH_MEMSET
This increases the performance of memcpy/memset
and also reduces the boot time.
This was tested on Trats2.
A quick test with trace. Boot time from start to main_loop() entry:
- ~1527ms - before this change (arch memset enabled for .bss clear)
- ~1384ms - after this change
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
This configures the Juno board to enable ethernet using the
SMSC9118 ethernet controller found in the board. Tested by
TFTP-booting a kernel over ethernet.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds generic board support for MCF547X/8X and MCF5445X.
It is based on the patch about common generic board support for
M68K architecture sent by Angelo.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
This patch extends OMAP3 support for AM/DM37xx and
introduces the AM3703-based Quipos Cairo board.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
For series testing purpose we need to boot some linux, therefore we enable
the needed features
- bootz
- devicetree
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
The board has been redesigned, therefore we need from now other I/O Pins to
mux and handle.
Older boards aren't supported from now anymore.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Due to several changes of the boot-process we've redesigned the default-
environment settings completly.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Customer wants to display some logo very quickly after power on, so we support
from now loading a compressed bmp.gz to the screen.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
time measurement of u-boot commands is needed very often during development.
We add this feature until development is completed. Maybe forever :)
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
It is often necessary to "break in" into boards bootloader commandline if
something fails or even for development purposes some parameters have to be
changed.
So we enable u-boot's CONFIG_NETCONSOLE feature.
We also modify Networksettings to apply with this new use-case.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Without this change the board support for these SPEAr boards would
be dropped soon. Generic board support seems to work just fine.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Saves having to remember to ask make for it explicitly.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Built and booted to a Linux prompt with no issues discovered. network and usb
access to the external mmc are ok. (my internal mmc is knackered at the h/w
level).
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
This board uses DDR DIMM. Reading SPD provides more flexibility.
Raw timing parameter code should be removed after debugging.
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
commit d9f43c8f5c sets
get_reset_cause() as static, but this conflicts with mx5
where its prototype is in sys_proto.h.
Drop it from sys_proto.h and drop print_cpuinfo from mx53_loco,
factorizing the call for this board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Add support for the Altera Arria V development kit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
