This must be defined by a board support file that want to use the
keymile common.c board_eth_init function that requires ethernet_present
to be defined.
Currently all the km architectures use it but the kmp204x architecture
later supported in this series does use another board_eth_init function
and thus does not define it.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This must be defined for all the keymile boards that use the common
i2c_abort function that is used to "reset" the I2C bus. These are
currently km82xx and km_arm boards.
The km83xx boards use other functions and thus do not need this.
This patch removes the CONFIG_SYS_I2C_INIT_BOARD from keymile-common.h
and defines it for km_arm.h and km82xx.h.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
as the keymile boards use now the new i2c multibus/multiadapter
framework, remove the EEprom_ivm Environmentvar, as not longer
needed.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-By: Holger Brunck <holger.brunck@keymile.com>
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection
to the switch MV88E6122. This switch has a connection to a frontport
ethernet interface. The ethernet port used for network booting is
automatically selected by u-boot. If a Piggy is plugged, the Piggy
port is selected (UEC2, eth1). If the Piggy isn't present, the
Frontport is selected (UEC0, eth0).
The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28)
and released at startup.
Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
For the the kmvect1 board we will also need a functionality to add an
offset to the IVMs MAC address, because these board will have two valid
ethernet ports for debugging purpose. So move the code to an own
function.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
For kmvect1 we need a special solution and for km_arm boards we already
have. So move the common code to the architectur specific file.
Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
The fanless boards now have a 7-digit (XXXXX-F) board name. This
triggers a border condition when reading this string in the IVM although
this string is smaller than the currenly read string size, but only by 1
character.
This patch corrects this by changing the size check condition for string
length. It is the same change that was done in the platform for this
same bug.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Stefan Bigler <stefan.bigler@keymile.com>
This code will also be used before reallocation and during this time we
are not allowed to do these printings.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
This adds a first support of the FPGA download for a PCIe FPGA based
on the BOCO2 CPLD.
This takes place in 3 steps, all done accessing the SPICTRL reg of the
BOCO2:
1) start the FPGA config with an access to the FPGA_PROG bit
2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1
for the end of the FPGA configuration (with a timeout)
3) reset the FPGA
4) finally remove the access to its config EEPROM from the FPGA so that
the CPU can update the FPGA configuration when the kernel is running
The boards with a PCIe FPGA but without BOCO2 still are supported.
The config option name is CONFIG_KM_FPGA_CONFIG
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
If the testpin is asserted, first check if a test_bank
variable is defined before trying to boot this
test_bank.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
kmcoge5ne starts the post tests if the testpin on
the board was enabled. Currently it does simply a memory
test.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Enabled application buffers in uboot to allow application chipselect
access in uboot.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MAC address begins at offset 1.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The common code should be valid for more than one architecture.
Therefore this code was reorganized and moved to the new
file km83xx_i2c.c
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This header is unneeded due to code which was removed in the
past.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Calucations of PRAM needs to take into account the 'rootfssize'.
Memory available to the linux kernel 'mem=' is in all cases set to the total
memory size minus the pram size.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
This prevents u-boot to print out "Can't overwrite "ethaddr""
each time a powerpc board starts.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
The MAC address stored in the inventory eeprom begins at offset 1.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Enable printout of i2c deblocking status if chips were in block
state or deblocking failed.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Be verbose if do_setboardid was called and print
correct names of variables in do_checkboardidhwk.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Common code should be valid for more than one architecture,
therefore the km82xx specific code was removed from common.c.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
This code is unused and therefore dead code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
The file common.c grows in the past. So move the IVM specific
code into an ivm.c file.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
This is unneeded here because we save the environment when
the board boots the first time. At this time we have set
the values already.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
The ethaddr is stored inside the inventory eeprom. During
boottime this value was read out and the ethaddr variable was
set. Previously this was only done if it ethaddr == NULL but
this is wrong for our ARM boards. Because ethaddr is at this
stage never NULL for ARM due to the random calculation of a
MAC address in mvgbe.c.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
These defines and the header keymile_hdlc_enet.h are obsolete
due to the removed hdlc code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
BoardId and HWKey are used to identify the HW class of a given board.
The correct values are stored in the inventory eeprom. During creation
time of a boot package the boardId and HWkey for the SW is stored in
the default environment and burned into the flash. During boottime
the values in the inventory and in the environment are compared to
avoid starting of a SW which is not authorized for this board.
Some bootpackages are allowed to run on a set of different boardId
hwKey. In this case the environment variable boardIdListHex was added
to the default environment. In this case the command iterates over the
pair values and compares them with the values read from the inventory
eeprom.
The syntax of such a boardIdListHex value is e.g.: 158_1 159_1 159_2
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
Read out board id and HW key from the IVM eeprom and set
these values as an environment variable.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch adds support for the MPC8247 based board mgcoge3ne.
Additionaly mgcoge2ne board supprot was removed, because due
to the mgcoge3ne, this board is obsolete and not longer
maintained.
The board is similar to mgcoge. The difference is that
a NUMONYX flash is used and a different SDRAM (256MB).
Also introduce CONFIG_KM_82XX to collect ppc82xx common
settings and remove staticness from the common set_pin function.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
Introduce a struct for the BFTICU FPGA to increase the readability of
the code. And the define CONFIG_SYS_BFTICU_BASE was removed because
the CONFIG_SYS_FPGA_BASE is already the base value for BFTICU registers.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
The hdlc implementation for mgcoge was initially developed,
but later on not used. Remove the C files, the references
in mgcoge.c and the Makefile to decrease maintenance effort.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch adds last_stage_init to all keymile boards. And
in the last stage init some environment variables for u-boot
were set. Currently these are pnvramaddr, pram and var address.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
Normaly the PIGGY_MAC_ADRESS can be read directly from the
IVM on keymile boards. On mgcoge3 it differs. Because there
are two piggy boards deployed the second MAC adress must be
calculated with the IVM mac adress and an offset. This patch
allows to set such a offset in the board config.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
This patch fix the i2c deblocking facility with the i2c HW-Controller.
The required delays for byte reading, the enhanced criteria for stop
the dummy read and required 5 start/stop sequences are added.
Add i2c deblocking before ivm eeprom read.
Improve i2c deblocking sequence by respecting stop hold time.
Cleaned function for deblocking. Have now one function i2c_make_abort()
available for bitbang, mpc82xx and mpc83xx harware controller.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
For the kmsupx5 a new header file was introduced km8321-common.h.
Now the common stuff from tuxa1, tuda1 and suvd3 was removed and
the new header file included.
The defines CONFIG_SYS_PIGGY_BASE and CONFIG_SYS_PIGGY_SIZE are
confusing. Because they actually describe the KMBEC FPGA values.
The KMBEC FPGA can be PRIO on kmeter1 or upio on mgcoge. Therefore
all the defines were renamed.
remove unneeded variable CONFIG_KM_DEF_NETDEV, as it is
already declared in keymile-common.h
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount
This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- use I/O accessors
-> For accessing the FPGA therefore a struct km_bec_fpga
is introduced.
- no longer externs needed
- to defines, that only select functions, don;t assign a
numeric value
- Codingstyle changes to prevent checkpatch errors/warnings
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The MACH_TYPE SUEN3 is now to specific for keymile boards, because
other boards similar to suen3 will follow. So the MACH_SUEN3 was renamed
to MACH_KM_KIRKWOOD.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
since commit 1384f3bb8a ethernet names
with spaces drop a
Warning: eth device name has a space!
message. This patch fix it for:
- "FEC ETHERNET" devices found on
mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
renamed to "FEC".
- "SCC ETHERNET" devices found on
mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
boards. Renamed to "FCC"
Tested on the kup4k board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
