Commit graph

22 commits

Author SHA1 Message Date
Alex Marginean
2d5d5266e1 drivers: net: phy: aquantia: make it less verbose
The driver now unconditionally prints some information that's not
universally useful.  Replace printf with debug.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2020-03-09 18:11:24 -05:00
Alex Marginean
0d8b0c917a drivers: net: phy: aquantia: drop XGMII as a valid system interface proto
Use either USXGMII or XFI in aquantia_set_proto and drop XGMII as a valid
protocol configuration.  The PHY doesn't support it, it's just used as an
alias for one of the other two protocols.

Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2020-03-09 18:11:24 -05:00
Alex Marginean
6d9bc2043a drivers: net: aquantia: check system interface too when checking for link up
In some cases the link on the system interface of the aquantia PHY comes up
after the link on line interface.  The link state loop only checks the line
side, which may result in first packet sent being lost.
Use aquantia_link_is_up instead, which checks both system and line side on
gen 2/3 PHYs to avoid losing the 1st packet.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:43 -06:00
Alex Marginean
05f86070c0 drivers: net: aquantia: set SMBus addr based on DT property
Aquantia PHYs have a SMBus interface mostly used for debug.  The addresses
on this interface are normally set up by PHY firmware, but depending on the
board they may end up not being unique.  Add an optional DT property used
to change SMBus address if needed.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:43 -06:00
Alex Marginean
7552ee9a01 drivers: net: aquantia: set MDI reversal based on DT property
MDI pins up to the RJ45 connector may be reversed on the board and the
default PHY configuration applied by firmware may or may not match that.
Add an optional DT property to configure MDI reversal for this case.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:43 -06:00
Alex Marginean
a301ec7a5a drivers: net: aquantia: set up SI protocol based on interface type
If PHY is not ready for data by the time _config is called, reconfigure the
PHY system interface to use the proper protocol based on phydev->interface,
just in case the defaults set by PHY firmware don't match current
configuration.

Signed-off-by: Florin Laurentiu Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Alex Marginean
5fe861b8b2 drivers: net: aquantia: add PHY generation information
Uses the data field in phy_driver structure to identify the PHY generation.
This is useful for custom configuration as non-generic PHY registers are
not 100% compatible between generations.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Alex Marginean
8a141d6e9c drivers: net: aquantia: use XFI, USXGMII interface types
The PHY supports XFI and USXGMII, the notable difference being that USX AN
is enabled for USXGMII.  Legacy code uses XGMII for any 10G proto and
detects whether USX AN should be enabled or not using a PHY status
register.  Keep that functionality too, so we don't break existing drivers.

Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Florin Chiculita
bf58916373 net: phy: aquantia: wait for phy init sequence to finish
Aquantia quad-phys may take longer to initialize. This commit adds
a polling mechanism for a global alarm bit that tells if phy init
sequence is completed.

Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Alexandru Marginean
14df216d10 drivers: net: phy: Use Aquantia driver for AQR112, AQR412
adds AQR112 and AQR412 to the list of supported PHYs using existing AQR
code.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-18 16:37:13 -05:00
Valentin-catalin Neacsu
c940646ed1 net: phy: aquantia: Set only autoneg on in register 4.c441
For AQR405 in register 4.c441 bit 15 was override with 0. This caused the
phy to not negotiate at 2.5GB rate with mac. To avoid
this override it needed first to know the previous value of reg 4.c441
and set only bit 3.

Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-05-08 17:27:00 -05:00
Valentin-catalin Neacsu
91c9cbabf9 net: phy: aquantia: Print information on config
Print information about Aquantia system interface and firmware loaded
on the phy.

Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-01-24 11:35:30 -06:00
Valentin-catalin Neacsu
c54bfbf96f net: phy: aquantia: Enable autoneg when on USXGMII
If System Interface protocol is USXGMII then enable USXGMII autoneg

Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-01-24 11:35:30 -06:00
Philipp Tomsich
a740ee913e lib: merge CRC16-CCITT into u-boot/crc.h
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure.  Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-08 20:18:32 -05:00
Jeremy Gebben
30a2c8cca8 net: phy: aquantia: autodetect if firmware needs to be loaded
If the phy reports a valid firmware version and doesn't indicate
a fault, skip loading the firmware.  This allows the same image
to be used on boards that have firmware storage and those that do not.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Jeremy Gebben
4506423ad2 net: phy: aquantia: add firmware loading support
Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Jeremy Gebben
1c6501088e configs: migrate CONFIG_PHY_AQUANTIA to Kconfig
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:36 -05:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Calvin Johnson
365108ef52 drivers: net: phy: Fix aquantia compilation with DM
With CONFIG_DM_ETH enabled, aquantia driver compilation fails with
below error. This patch fixes the issue by including dm.h.

drivers/net/phy/aquantia.c: In function ‘aquantia_startup’:
drivers/net/phy/aquantia.c:73:21: error: dereferencing pointer to
incomplete
type ‘struct udevice’
          phydev->dev->name);
		     ^~

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:28 -05:00
Mingkai Hu
19c9ddaa4f driver: net: phylib: add support for aquantia AQR106/107 PHY
This patch adds support for aquantia AQR106/107 PHY.

Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-06 10:45:04 -05:00
Shaohui Xie
f8642ba6dd net: phy: added aquantia PHY AQR405 support
The phy can share driver with other aquantia PHYs, so we only
add PHY ID.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:13 -08:00
Shaohui Xie
f7c38cf827 phylib: add support for aquantia PHYs
This patch supports AQ1202, AQ2104, AQR105 PHY.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16 09:32:11 -08:00