Add two ELE API: ele_return_lifecycle_update and ele_write_secure_fuse
Add two cmd: ahab_return_lifecycle and ahab_sec_fuse_prog
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix build warning:
warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3
has type ‘u64’ {aka ‘long long unsigned int’} [-Wformat=]
printf("can't find memreg for image %d load address 0x%x, error %d\n",
warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but
argument 3 has type ‘sc_faddr_t’ {aka ‘long long unsigned int’} [-Wformat=]
debug("memreg %u 0x%lx -- 0x%lx\n", mr, start, end);
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The return value is int type, not sc_err_t(u8), correct the usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
The return value is int type, not sc_err_t(u8), correct the usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Running a memtest in U-Boot and Linux shows that some Colibri iMX6
produce bitflips at temperatures above 60°C. This happens because the
RALAT and WALAT values on the Colibri iMX6 are too low. The problems
were introduced by commit 09dbac8174 ("mx6: ddr: Restore ralat/walat
in write level calibration") before the calibration process overwrote
the values and set them to the maximum value. With this commit, we make
sure that the RALAT and WALAT values are set to the maximum values
again. This has been proven to work for years.
Fixes: 09dbac8174 ("mx6: ddr: Restore ralat/walat in write level calibration")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Add support for Winbond 256M-bit flash w25q256jwm.
Performed basic erase/write/readback operations on
ZynqMP zc1751+dc1 board.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If cs gpio is requested with ACTIVE_HIGH flag, it will
be pulled low(i.e. active). This is not what we expected.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
XTX changed full company name from "XTX Technology (Shenzhen) Limited
to "XTX Technology Limited" since 2020,So remove "(Shenzhen)".
Signed-off-by: Bruce Suen <bruce_suen@163.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to Documentation/devicetree/bindings/spi/spi-gpio.yaml
from Linux, the recommended spio-gpio properties are:
sck-gpios, miso-gpios and mosi-gpios.
gpio-sck, gpio-mosi and gpio-miso are considered deprecated.
Update the bindings to suggest the recommeded properties.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to Documentation/devicetree/bindings/spi/spi-gpio.yaml
from Linux, the recommended spio-gpio properties are:
sck-gpios, miso-gpios and mosi-gpios.
gpio-sck, gpio-mosi and gpio-miso are considered deprecated.
Currently, U-Boot only supports the deprecated properties.
Allow the soft_spi driver to support both the new and old properties.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Current code expects that SPI_TX_BYTE is single bit mode
but it is wrong. It indicates byte program mode,
not single bit mode.
If SPI_TX_DUAL, SPI_TX_QUAD and SPI_TX_OCTAL bits are not set,
the default transfer bus width is single bit.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The newer BCMBCA SoCs such as BCM6756, BCM4912 and BCM6855 include an
updated SPI controller that add the capability to allow the driver to
control chip select explicitly. Driver can control and keep cs low
between the transfers natively. Hence the dummy cs workaround or prepend
mode found in the bcm63xx-hsspi driver are no longer needed and this new
driver is much cleaner.
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-15-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Due to the controller limitation to keep the chip select low during the
bus idle time between the transfer, a dummy cs workaround was used when
this driver was first upstreamed to the u-boot based on linux kernel
driver. It basically picks the dummy cs as !actual_cs so typically dummy
cs is 1 when most of the case only cs 0 is used in the board design.
Then invert the polarity of both cs and tell the controller to start the
transfers using dummy cs. Assuming both cs are active low before the
inversion, effectively this keeps dummy cs high and actual cs low during
the transfer and workaround the issue.
This workaround requires that dummy cs 1 pin to is set to SPI chip
selection function in the pinmux when the transfer clock is above 25MHz.
The old chips likely have default pinmux set to chip select on the dummy
cs pin so it works but this is not case for the new Broadband BCA chips
and this workaround stop working. This is specifically an issue to
support SPI NAND and SPI NOR flash because these flash devices can
typically run at or above 100MHz.
This patch utilizes the prepend feature of the controller to combine the
multiple transfers in the same message to a single transfer when
possible. This way there is no need to keep clock low between transfers
and solve the issue without any pinmux requirement.
Multiple transfers within a SPI message may be combined into one
transfer if the following are all true:
* One or more half duplex write transfer in single bit mode
* Optional full duplex read/write at the end
* No delay and cs_change between transfers
Most of the SPI device meets this requirements such as SPI NOR, SPI NAND
flash, Broadcom SPI voice card and etc. So this change switches to the
prepend mode as the default mode. For any SPI message that does not meet
the above requirement, we switch to original dummy cs mode but limit the
clock rate to the safe 25MHz.
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-12-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
New compatible string brcm,bcmbca-hsspi-v1.0 is introduced based on
dts document brcm,bcm63xx-hsspi.yaml. Add it to the driver to support
this new binding.
Port from linux patch:
Link: https://lore.kernel.org/r/20230207065826.285013-6-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the driver always sets the controller to dual data bit mode
for both tx and rx data in the profile mode control register even for
single data bit transfer. Luckily the opcode is set correctly according
to SPI transfer data bit width so it does not actually cause issues.
This change fixes the problem by setting tx and rx data bit mode field
correctly according to the actual SPI transfer tx and rx data bit width.
Fixes: 29cc4368ad ("dm: spi: add BCM63xx HSSPI driver")
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-11-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
ARCH_BCMBCA was introduced to cover individual Broadcom broadband SoC
for common features and IP blocks. Use this config instead of each chip
config as the Kconfig dependency for Broadcom HSSPI driver.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for an optional external chip-select gpio.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Remove the platform data header because its content is only used by the
driver.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Rename the flush function into pl022_spi_flush to avoid conflicting
types with previous declaration of the function in stdio.h header.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Align the compatible property with the kernel device tree binding [1]
by removing the '-spi' suffix.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/spi/spi-pl022.yaml
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The CN9130 SoC (an ARMADA 8K type) has both a NAND Flash Controller and
a generic local bus controller (Device Bus Controller) that share common
pins.
With a board design that incorporates both a NAND flash and uses
the Device Bus (in our case for an SRAM) accessing the Device Bus device
fails unless the NfArbiterEn bit is set. Setting the bit enables
arbitration between the Device Bus and the NAND flash.
Since there is no obvious downside in enabling this for designs that
don't require arbitration, we always enable it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The NAND flash controller (NFC) on the AC5/AC5X SoC is the same as
the NFC used on other Marvell SoCs. It does have the additional
restriction of only supporting SDR timing modes up to 3.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The NF_CLK for the AC5 SoC runs at 400MHz. There's no strapping
or gating require so just add a mvebu_get_nand_clock() that
returns this value.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The AC5/AC5X SoC has a NAND flash controller. Add this to the
SoC device tree.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Update the Thecus N2350 DTS to conform with latest device-tree binding
and styles.
- Correct typo in mdio node.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Add basic config for Sipeed Lichee PI 4A board which make it capable of
booting into serial console.
Reviewed-by: Wei Fu <wefu@redhat.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's
TH1520 SoC, only minimal device tree and serial console are enabled,
so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by: Wei Fu <wefu@redhat.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
As the RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, we rename SiFive CLINT to RISC-V
ALINT in the source tree to be future-proof.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This RISC-V ACLINT specification [1] defines a set of memory mapped
devices which provide inter-processor interrupts (IPI) and timer
functionalities for each HART on a multi-HART RISC-V platform.
The RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, however the device tree binding
is a new one. This change updates the sifive clint ipi driver to
support ACLINT mswi device, by checking the per-driver data field of
the ACLINT mtimer driver to determine whether a syscon based approach
needs to be taken to get the base address of the ACLINT mswi device.
[1] https://github.com/riscv/riscv-aclint/blob/main/riscv-aclint.adoc
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This RISC-V ACLINT specification [1] defines a set of memory mapped
devices which provide inter-processor interrupts (IPI) and timer
functionalities for each HART on a multi-HART RISC-V platform.
The RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, however the device tree binding
is a new one. This change updates the sifive clint timer driver to
support ACLINT mtimer device, using a per-driver data field to hold
the mtimer offset to the base address encoded in the mtimer node.
[1] https://github.com/riscv/riscv-aclint/blob/main/riscv-aclint.adoc
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
The main difference between StarFive VisionFive 2 1.2A and 1.3B is gmac.
You can read the PCB version of the current board by
get_pcb_revision_from_eeprom(), and then dynamically configure the
difference of gmac in spl_perform_fixups() according to different PCB
versions, so that one DT and one defconfig can support both 1.2A and
1.3B versions, which is more user-friendly.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
StarFive VisionFive 2 has two versions, 1.2A and 1.3B, each version of
DDR capacity includes 2G/4G/8G, a DT can not support multiple
capacities, so the capacity size information is recorded to EEPROM, when
DDR initialization required capacity size information is read from
EEPROM.
If there is no information in EEPROM, it is initialized with the default
size defined in DT.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enabled ID_EEPROM and I2C configuration for StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-By: Leo Yu-Chi Linag <ycliang@andestech.com>
