83xx processor family has many reset sources, such as
power on reset, software hard reset, software soft reset,
JTAG, bus monitor, software watchdog, check stop reset,
external hard reset, external software reset.
sometimes, to figure out the fault of system, we need to
know the cause of reset early before the prompt of
u-boot present.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The relocation fixup didn't handle the malloc pointer initialization
correctly. This patch fixes this problem. Tested successfully on 4xx.
The relocation fixup patches for 4xx will follow soon.
Signed-off-by: Stefan Roese <sr@denx.de>
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
- Show on the Status LEDs, some States of the board.
- Get the MAC addresses from the EEProm
- use PREBOOT
- use the CF on the board.
- check the U-Boot image in the Flash with a SHA1
checksum.
- use dynamic TLB entries generation for the SDRAM
Signed-off-by: Heiko Schocher <hs@denx.de>
Search the exception table with linear algorithm instead of
bisecting algorithm.
Because the exception table might be unsorted.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Conflicts:
drivers/cfi_flash.c
The patch by Heiko Schocher <hs@pollux.denx.de> on Jan, 19, 2007
fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support
mpc7448hpc2 board.
The original search_one_table() function code can only processes the search
for the exception occurring in FLASH/ROM, because the exception and fixup
table usually locate in FLASH. If the exception address is also in
FLASH, it will be OK.
If the exception occurs in RAM, after the u-boot relocation, a
relocation offset should be added.
clean up the code in cpu/74xx_7xx/cpu.c
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The conflicts due to a new mpc7448 p3m7448 board is in the main tree.
Merge branch 'master' into hpc2
Conflicts:
MAKEALL
cpu/74xx_7xx/cpu.c
cpu/74xx_7xx/cpu_init.c
cpu/74xx_7xx/speed.c
Replace all instances of CFG_IMMRBAR with CFG_IMMR, so that the 83xx
tree matches the other 8xxx trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
1. Add 7447A and 7448 processor support.
2. Add the following flags.
CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically
(such as by switch on board), this flag should be set.
CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot
relocates to RAM, this flag should be set.
CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the
system hang in exception, this flag should be set.
There is a design issue for tsi108/109 pci configure read. When pci scan
the slots, if there is no pci card, the tsi108/9 will cause a machine
check exception for mpc7448 processor.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006
Modifications are based on the linux kernel approach and
support two use cases:
1) Add O= to the make command line
'make O=/tmp/build all'
2) Set environement variable BUILD_DIR to point to the desired location
'export BUILD_DIR=/tmp/build'
'make'
The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'
Command line 'O=' setting overrides BUILD_DIR environent variable.
When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
- Support for TQM8541/8555 boards added.
- Complete rework of TQM8540/8560 support.
- Common TQM85xx code now supports all current TQM85xx platforms
(TQM8540/8541/8555/8560).
- DDR SDRAM size detection added.
- CAS latency default values can be overwritten by setting "serial#"
to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used.
If problems are detected with this non default CAS latency,
the defualt values will be used instead.
- FLASH size detection added.
- Moved FCC ethernet driver initialization behind TSEC driver init
-> TSEC is first device.
Patch by Stefan Roese, 30 Nov 2005
