Flag status register polling is required for micron 512Mb flash
devices onwards, for performing erase/program operations.
Like polling for WIP(Write-In-Progress) bit in read status register,
spi_flash_cmd_wait_ready will poll for PEC(Program-Erase-Control)
bit in flag status register.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Defined bank addr code on CONFIG_SPI_FLASH_BAR macro, to reduce the
size for existing boards which has < 16Mbytes SPI flashes.
It's upto user which has provision to use the bank addr code for
flashes which has > 16Mbytes.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Read the flash bank addr register to get the state of bank in
a perticular flash. and also bank write happens only when there is
a change in bank selection from user.
bank read only valid for flashes which has > 16Mbytes those are
opearted in 3-byte addr mode, each bank occupies 16Mytes.
Suppose if the flash has 64Mbytes size consists of 4 banks like
bank0, bank1, bank2 and bank3.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bank/Extended addr commands are specific to particular
flash vendor so discover them based on the idocode0.
Assign the discovered bank commands to spi_flash members
so-that the bank read/write will use their specific operations.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Use a negative value of CONFIG_ENV_OFFSET for all NVIDIA reference boards
that store the U-Boot environment in the 2nd eMMC boot partition. This
makes U-Boot agnostic to the size of the eMMC boot partition, which can
vary depending on which eMMC device was actually stuffed into the board.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Enhance the MMC core to calculate the size of each MMC partition, and
update mmc->capacity whenever a partition is selected. This causes:
mmc dev 0 1 ; mmcinfo
... to report the size of the currently selected partition, rather than
always reporting the size of the user partition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The commit d196bd8 (env_mmc: add support for redundant environment)
introduce the following compile error when enable redundant
environment support with MMC
---8<---
env_mmc.c:149: error: 'env_t' has no member named 'flags'
env_mmc.c:248: error: 'env_t' has no member named 'flags'
env_mmc.c:248: error: 'env_t' has no member named 'flags'
env_mmc.c:250: error: 'env_t' has no member named 'flags'
env_mmc.c:250: error: 'env_t' has no member named 'flags'
env_mmc.c:252: error: 'env_t' has no member named 'flags'
env_mmc.c:252: error: 'env_t' has no member named 'flags'
env_mmc.c:254: error: 'env_t' has no member named 'flags'
env_mmc.c:254: error: 'env_t' has no member named 'flags'
env_mmc.c:267: error: 'env_t' has no member named 'flags'
make[1]: *** [env_mmc.o] Error 1
--->8---
Add this patch to fix it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
LP-8x4x is a programmable automation controller by ICP DAS. It is
shipped with outdated U-Boot v1.3.0
This patch adds enough supports to boot the board:
- 128M of 128M SDRAM
- 32M of 48M NOR Flash memory
- 1 of 4 Serial consoles (PXA FFUART)
- 2 of 2 Ethernet controllers (DM9000)
Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Series-to: u-boot
Series-cc: marex
This patch adds support to both Faraday FUSBH200 and FOTG210,
the differences between Faraday EHCI and standard EHCI are
listed bellow:
1. The PORTSC starts at 0x30 instead of 0x44.
2. The CONFIGFLAG(0x40) is not only un-implemented, and
also has its address space removed.
3. Faraday EHCI is a TDI design, but it doesn't
compatible with the general TDI implementation
found at both U-Boot and Linux.
4. The ISOC descriptors differ from standard EHCI in
several ways. But since U-boot doesn't support ISOC,
we don't have to worry about that.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
The flash_info_t->start[] field is limited in size by CONFIG_SYS_MAX_FLASH_SECT
macro, which is set to 19 for this board in the board config file. If we inspect
the board/ppmc7xx/flash.c closely, especially the flash_get_size() function, we
can notice the "switch ((long)flashtest)" at around line 80 having a few results
which will set flash_info_t->sector_count to value higher than 19, for example
"case AMD_ID_LV640U" will set it to 128. Notice that right underneath, iteration
over flash_info_t->start[] happens and the upper bound for the interation is
flash_info_t->sector_count. Now if the sector_count is 128 as it is for the
AMD_ID_LV640U case, but the CONFIG_SYS_MAX_FLASH_SECT limiting the start[] is
only 19, an access past the start[] array much happen. Moreover, during this
iteration, the field is written to, so memory corruption is inevitable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Richard Danter <richard.danter@windriver.com>
C99's strict aliasing rules are insane to use in low-level code such as a
bootloader, but as Wolfgang has rejected -fno-strict-aliasing in the
past, add a union so that 16-bit accesses can be performed.
Compile-tested only.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
Add MMC support for da830 boards in order to perform
mmc operations(read,write and erase).
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Add some useful functions, and the corresponding definitions.
Add support for powering on the dra7xx_evm SD/MMC LDO
(courtesy Lokesh Vutla <lokeshvutla@ti.com>).
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: Tom Rini <trini@ti.com>
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
The sys_clk on the dra evm board is 20MHZ.
Changing the configuration for the same.
And also moving V_SCLK, V_OSCK defines to
arch/clock.h for OMAP4+ boards.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The registers that are used for device identification
are changed from OMAP5 to DRA7xx.
Using the correct registers for DRA7xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The pci_indirect.c file is always compiled when
CONFIG_PCI is defined although the indirect PCI
bridge support is not needed by every board.
Introduce a new CONFIG_PCI_INDIRECT_BRIDGE
config option and only compile indirect PCI
bridge support if this options is enabled.
Also add the new option into the configuration
files of the boards which needs that.
Compile tested for powerpc, x86, arm and nds32.
MAKEALL results:
powerpc:
--------------------- SUMMARY ----------------------------
Boards compiled: 641
Boards with warnings but no errors: 2 ( ELPPC MPC8323ERDB )
----------------------------------------------------------
Note: the warnings for ELPPC and MPC8323ERDB are present even
without the actual patch.
x86:
--------------------- SUMMARY ----------------------------
Boards compiled: 1
----------------------------------------------------------
arm:
--------------------- SUMMARY ----------------------------
Boards compiled: 311
----------------------------------------------------------
nds32:
--------------------- SUMMARY ----------------------------
Boards compiled: 3
----------------------------------------------------------
Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
This commit refactors common/board_f.c and common/board_r.c
in order to delete the dest_addr and dest_addr_sp from
gd_t struct.
As mentioned as follows in include/asm-generic/global_data.h,
/* TODO: is this the same as relocaddr, or something else? */
unsigned long dest_addr; /* Post-relocation address of U-Boot */
dest_addr is the same as relocaddr.
Likewise, dest_addr_sp is the same as start_addr_sp.
It seemed dest_addr/dest_addr_sp was used only as a scratch variable
to calculate relocaddr/start_addr_sp, respectively.
With a little refactoring, we can delete dest_addr and dest_addr_sp.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Jump into full u-boot mode if a 'c' character is received on the uart.
We need to adjust the spl bss/malloc area to not overlap with the
loadaddr of the kernel (sdram + 32k), so move it past u-boot instead.
For raw mmc, we store the kernel parameter area in the free space after
the MBR (if used). For nand, we use the last sector of the partition
reserved for u-boot.
This also enables the spl command in the full u-boot so the kernel
parameter area snapshot can be created.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
When running the "save" command several times on a mx6qsabresd we see:
U-Boot > save
Saving Environment to MMC...
Writing to MMC(1)... done
U-Boot > save
Saving Environment to MMC...
MMC partition switch failed
U-Boot > save
Saving Environment to MMC...
Writing to MMC(1)... done
U-Boot > save
Saving Environment to MMC...
MMC partition switch failed
U-Boot > save
Saving Environment to MMC...
Writing to MMC(1)... done
U-Boot > save
Saving Environment to MMC...
MMC partition switch failed
This issue is caused by the incorrect usage of CONFIG_SYS_MMC_ENV_PART.
CONFIG_SYS_MMC_ENV_PART should be used to specify the mmc partition that stores
the environment variables.
On some imx boards it is been incorrectly used to pass the partition of kernel
and dtb files for the 'mmcpart' script variable.
Remove the CONFIG_SYS_MMC_ENV_PART usage and configure the 'mmcpart' variable
directly.
Reported-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
The location of valid scratch space is dependent on SoC, so move that
there. On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR. On
am33xx/ti814x we want to use what the ROM defines as "public stack"
which is the area after our defined download image space. Correct the
comment about and location of CONFIG_SPL_TEXT_BASE.
Signed-off-by: Tom Rini <trini@ti.com>
Add a DT simple-framebuffer node to DT when booting the Linux kernel.
This will allow the kernel to inherit the framebuffer configuration from
U-Boot, and display a graphical boot console, and even run a full SW-
rendered X server.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
simple-framebuffer is a new device tree binding that describes a pre-
configured frame-buffer memory region and its format. The Linux kernel
contains a driver that supports this binding. Implement functions to
create a DT node (or fill in an existing node) with parameters that
describe the framebuffer format that U-Boot is using.
This will be immediately used by the Raspberry Pi board in U-Boot, and
likely will be used by the Samsung ARM ChromeBook support soon too. It
could well be used by many other boards (e.g. Tegra boards with built-in
LCD panels, which aren't yet supported by the Linux kernel).
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
Prior to Sricharan's cleanup of the boot parameter saving code, we
did not make use of NON_SECURE_SRAM_START on am33xx, so it wasn't a
problem that the address was pointing to the middle of our running SPL.
Correct to point to the base location of the download image area.
Increase CONFIG_SPL_TEXT_BASE to account for this scratch area being
used. As part of correcting these tests, make use of the fact that
we've always been placing our stack outside of the download image area
(which is fine, once the downloaded image is run, ROM is gone) so
correct the max size test to be the ROM defined top of the download area
to where we link/load at.
Signed-off-by: Tom Rini <trini@ti.com>
---
Changes in v2:
- Fix typo noted by Peter Korsgaard
Now that the code for loading these three images from a FIT is common, we
don't need individual boostage IDs for each of them.
Note: there are some minor changes in the bootstage numbering, particuarly
for kernel loading. I don't believe this matters.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new common code to load a flat device tree. Also fix up a few casts
so that this code works with sandbox. Other than that the functionality
should not change.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present code to load an image from a FIT is duplicated in the three
places where it is needed (kernel, fdt, ramdisk).
The differences between these different code copies is fairly minor.
Create a new function in the fit code which can handle any of the
requirements of those cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Loading a ramdisk, kernel or FDT goes through similar stages. Create
a block of IDs for each task, and define a consistent numbering within
the block. This will allow use of common code for image loading.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are two implementations of abortboot(). Turn these into two separate
functions, and create a single abortboot() which calls either one or the
other.
Also it seems that nothing uses abortboot() outside main, so make it static.
At this point there is no further use of CONFIG_MENU in main.c.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This is not currently used, since autoboot is not enabled for this
board, but the string is missing a parameter. Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add minimal support (only boot from mmc device) for the Congatec
Conga-QEVAl Evaluation Carrier Board with conga-Qmx6q (i.MX6 Quad
processor) module.
Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
