* Since the emmc isn't always programed trying to load the fs from the
emmc causes boot failures/kernel panic.
* The current bootcmd is set to:
bootcmd=run findfdt; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; \
setenv mmcroot /dev/mmcblk0p2 rw; run mmcboot;
My guess is the env variables should be set so that sd card boot
(dt,kernel,fs) is the default and then fallback to emmc if it fails (no
sd card detected)
The current bootcmd attempts to set mmcroot to the sd card rootfs but
that code doesn't run due to mmcboot being ran early on.
Signed-off-by: Franklin Cooper Jr. <fcooper@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
If we want to have two sections, one on each EMIF, without
interleaving, current code wouldn't enable emif2. Fix that
problem.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
there's no such function usb3_phy_power(),
it's likely that author meant to call,
usb_phy_power() instead, but that's already
called properly from xhci-omap.c.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
some boards might want to use USB1 for host,
without fiddling those registers it'll be
impossible.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Those regulators don't have any coupling with
what they supply, so remove the suffixes in order
to not confuse anybody.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Out of all OMAP5-like boards, only one of them
needs CONFIG_MISC_INIT_R, so it's best to enable
that for that particular board only, instead of
enabling for all boards unconditionally.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
It has been found that this change breaks the case of an appended device
tree file, so for the problem in question some other solution must be
found.
This reverts commit c6150aaf2f.
Reported-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Reported-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Confirmed-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Tom Rini <trini@ti.com>
The changes to introduce loff_t into filesize means that we need to do
64bit math on 32bit platforms. Make sure we use the right wrappers for
these operations.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Pierre Aubert <p.aubert@staubli.com>
After commit 933cdbb479: "fdt: Try to use fdt_address_cells()/fdt_size_cells()"
I noticed that allwinner boards would no longer boot.
Switching to fdt_address_cells / fdt_size_cells changes the result from
bytes to 32 bit words, so when we increment pointers into the blob, we must
do so by 32 bit words now.
This commit makes allwinner boards boot again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Vince Hsu <vinceh@nvidia.com>
If CONFIG_OF_CONTROL is defined, search device tree nodes that are
compatible with "panasonic,uniphier-ehci" and take the base address
from their "reg" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
This commit implements the ofdata_to_platdata handler for the UniPhier
serial driver and adds serial device nodes to the device tree sources.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. Consequently, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they do not
support GPIO.
In the first place, GPIO has nothing to do with OF_CONTROL.
It is wrong that lib/fdtdec.c includes GPIO functions; it should
be split into two files, FDT-common things and GPIO things.
It is, however, a pretty big work to fix that correctly.
This is a compromised commit to add a dummy <asm/arch/gpio.h>
to support OF_CONTROL for UniPhier platform. This dummy header
will be removed after FDT-GPIO stuff is fixed correctly.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_path_offset() checks an alias too.
fdtdec_get_alias_node(blob, "foo") is equivalent to
fdt_path_offset(blob, "foo").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The initramfs is currently only relocated if the user calls
the bootm ramdisk subcommand. If bootm should be used without
subcommands, the arch-specific bootm code needs to implement
the relocation.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
After all MIPS boards are switched to generic-board, the
MIPS specific board.c can be removed.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
To get correct stack walking and backtrace functionality in gdb,
registers fp and ra should be initialized before calling board_init_f
or board_init_r. Thus allocating stack space and zeroing it as it is
currently done in board.c becomes obsolete.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Merge struct s3c2410_nand and struct s3c2440_nand into one unified
struct s3c24x0_nand. While at it, fix up and rename the functions
to retrieve the NAND base address and fix up the s3c NAND driver to
reflect this change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
This patch disables subpage writes for vf610_nfc nand
driver. This is required, as without this fix, writing
unaligned u-boot images with DFU results in a hang.
Trying to write unalgined binary images also results
in a hang, without disabling subpage writes.
Patch has been tested on a Colibri VF61 module.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Some but not all of implementations of the Denali NAND controller
have hardware circuits to detect the device parameters such as
page_size, erase_size, etc. Even on those SoCs with such hardware
supported, the hardware is known to detect wrong parameters for some
nasty (almost buggy) NAND devices. The device parameters detected
during nand_scan_ident() are more trustworthy.
This commit sets some hardware registers to mtd->pagesize,
mtd->oobsize, etc. in the code between nand_scan_ident() and
nand_scan_tail().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
Some variants of the Denali NAND controller need some registers
set up based on the device information that has been detected during
nand_scan_ident().
CONFIG_SYS_NAND_SELF_INIT has to be defined to insert code between
nand_scan_ident() and nand_scan_tail(). It is also helpful to reduce
the difference between this driver and its Linux counterpart because
this driver was ported from Linux. Moreover, doc/README.nand recommends
to use CONFIG_SYS_NAND_SELF_INIT.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
Commit ff94bc40af
("mtd, ubi, ubifs: resync with Linux-3.14")
accidentally reverted part of the commit
13f0fd94e3
("NAND: Scan bad blocks lazily.").
Reinstate the change as by commit
fb49454b1b
("nand: reinstate lazy bad block scanning")
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Heiko Schocher <hs@denx.de>
Commit 9f12cd0e06 has broken SPL EXT support.
This patch update error code check to get SPL EXT support working again.
Tested on a Pandaboard (rev. A3).
Reviewed-by: Suriyan Ramasami <suriyan.r@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
This is a rare event and should not happen. When it does it is confusing to
work out why. At least we should print a message.
Adjust the emulator to always print decode errors to the console.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there are DEBUG options spread around the place. If you enable
one and not another you can end up with an emulator that does not work,
since each file can have a different view of what the registers look like.
To fix this, create a global CONFIG_X86EMU_DEBUG option that keeps
everything consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
As well as locating the ROM on the PCI bus, allow the ROM to be supplied to
the emulator. Split the init up a little so that callers can supply their
own interrupt routines. Also allow a vesa mode to be provided, to be
selected once the BIOS run is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is an implicit assumption that x86 machines want to use raw I/O in the
BIOS emulator, but this should be selectable. Add an CONFIG_X86EMU_RAW_IO
option to control it instead.
Also fix a few bugs which cause warnings on x86 and adjust the Makefile to
remove the assumption that only PowerPC uses the emulator.
Signed-off-by: Simon Glass <sjg@chromium.org>
