Commit graph

56066 commits

Author SHA1 Message Date
Shubhrajyoti Datta
941f61fe80 arm64: zynqmp: Update the OPPs for cpu freq
Add operating-points-v2.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:07 +01:00
Michal Simek
585ca873ef arm64: zynqmp: Add references to cpu nodes
Add missing references to all cpu nodes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:07 +01:00
Michal Simek
40d1f8af17 arm64: zynqmp: Wire QSPI boot mode for SPL
ZynqMP qspi driver is on the way to mainline

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:02 +01:00
Michal Simek
96894d3a9e arm64: zynqmp: Enable debug uart for zc1751 dc5
Showing uart earlier.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Michal Simek
b030fedf63 arm64: zynqmp: Add new ID for RFSoC
This ID is available on zc1254.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Michal Simek
494fffe70d arm64: zynqmp: Add support for CG/EG/EV device detection
Version string has unused fields 31:20 which can be used for exporting 9
bits from efuse IPDISABLE regs to recognize eg/cg/ev devices.

These efuse bits are setup for certain devices.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Michal Simek
8ebdf9efad arm64: zynqmp: Use u32 type instead of uint32_t
Warning is reported by checkpatch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Michal Simek
011f0c4f7c arm64: zynqmp: Add SD1 level shifter mode to alternative selection
Extend Kconfig to cover SD1 level shifter mode.

Reported-by: Jason Wu <jason.hy.wu@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Siva Durga Prasad Paladugu
89401481bd arm64: zynqmp: Enable config DEFINE_TCM_OCM_MMAP if CONFIG_MP defined
This modifies default value of config DEFINE_TCM_OCM_MMAP
to yes if CONFIG_MP is defined MP supports needs OCM and TCM
part of memory map.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Michal Simek
c85a6b79d1 tools: mkimage: Extend mkimage to also include pmufw
The patch is adding external pmufw "Platform Management Unit firmware"
to boot.bin image. Boot.bin is a Xilinx format which bootrom is capable
to read and boot the system. pmufw is copied to the header data section
follows by u-boot-spl.bin. pmufw is consumed by PMU unit (Microblaze)
and SPL runs on a53-0.

This is generated command line when PMUFW_INIT_FILE is setup.

./tools/mkimage -T zynqmpimage -R ./"" -n
./"board/xilinx/zynqmp/pmufw.bin" -d spl/u-boot-spl.bin spl/boot.bin

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:57 +01:00
Siva Durga Prasad Paladugu
e042d36e17 arm64: zynqmp: Provide a Kconfig option to use specified memory for MMU table
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:56 +01:00
Siva Durga Prasad Paladugu
f322ad604e arm64: zynqmp: mp: Correct the R5 release sequence
This patch corrects the R5 release sequence by adding the
below steps.
1. Flush dcache to ensure that image loaded into memory.
2. Keep R5 reset just to ensure R5 in reset.
3. Disable caches before accessing TCM as with out this
   A53 can do speculative and may result in ECC failures
   if TCM's are not initialized. So, it is always better
   to disable dcaches before accessing TCM and enable back.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:56 +01:00
Michal Simek
62e950fad3 arm64: zynqmp: Remove slcr with mio status pin detection
This code is not used on this platform and it is not called.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:55 +01:00
Michal Simek
e81589ea44 ata: Fix ahci wording
s/achi_/ahci_/g

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:52 +01:00
Michal Simek
dea4d2f01d arm: zynq: Add mini u-boot configuration for zynq
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.

ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE  0x40000
was hardcoded.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:47 +01:00
Michal Simek
70ca290422 arm: zynq: Sort dts names
Sort names.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:45 +01:00
Michal Simek
809704eb4f arm: zynq: Move ZYNQ_SERIAL to Kconfig
Move cadence/zynq serial driver via Kconfig

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:45 +01:00
Michal Simek
7fad6125e4 arm: zynq: Enable FPGA/FPGA_XILINX via Kconfig
Enabling fpga via Kconfig.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:45 +01:00
Michal Simek
da3f003be1 arm: zynq: Return value from fdtdec_setup_memory_banksize directly
There is no reason not to return return value from above function.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:44 +01:00
Michal Simek
bc133e80ae arm: zynq: Add board support for cc108
cc108 board is wiring uart via PL which is good platform for SPL fpga
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:40 +01:00
Michal Simek
7111d6ed86 arm: zynq: Enable qspi for zc770_xm013
Enable qspi driver and flashes for this board.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Michal Simek
b2ff7fb673 arm: zynq: Enable MACRONIX flash for zc702/zc706/zc770 xm010
Enable MACRONIX flash for boards with QSPI enabled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Michal Simek
4c82ab9d29 arm: zynq: Enable debug console on zc770 xm010 by default
Enable debug console.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Michal Simek
20dff6f153 arm: zynq: Enable bootz command for Xilinx platforms
bootz command is valid way how to boot Linux kernel. Enable it by
default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Michal Simek
534f7e0235 arm: zynq: Sync location of DT properties with Linux
This is trival change which only ensures the same location with Linux
kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Michal Simek
bd28e5ca8e arm: zynq: Remove empty ifdef env structures from config file
All these configs were moved to Kconfig that's why this empty ifdef
structure is not needed anymore.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Sai Pavan Boddu
5fad1ab3d0 arm: zynq: Add device-type property for zynq ethernet phy nodes
Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.

Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Chirag Parekh
57bcc7fd37 arm: zynq: Add SCL & SDA GPIO entries for recovery
Wire i2c pinmuxing gpio recovery for zc702.

Signed-off-by: Chirag Parekh <chiragp@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Jeff Westfahl
8000d6ea3f mtd: nand: zynq: Add a config option to use 1st stage bootloader timing
In legacy method, 1st stage bootloader was used to configure the HW
setting such as NAND timing. Hence, adding a config option in Zynq
NAND driver for the compatibility of device that using 1st stage
bootloder instead of U-boot SPL.

This commit is to add config option
CONFIG_NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS that allow NAND driver use
timing values set by the 1st stage bootloader, instead of the hard-coded
values in the Zynq NAND driver.

Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Scott Wood <oss@buserror.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Tom McLeod
413ab5b0e1 arm: zynq: Add support for SYZYGY Hub board
Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board
contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports
booting from SD.

Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Michal Simek <monstr@monstr.eu>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Heinrich Schuchardt
549d684d4e arm64: zynqmp: remove unnecessary logical constraint
In

if (a || b)
else if (!a)

the constraint (!a) is always true if else is reached and
can be removed.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Tom Rini
65972a0b62 Merge git://git.denx.de/u-boot-socfpga 2017-11-28 09:30:36 -05:00
Tom Rini
53fe692652 Merge git://git.denx.de/u-boot-usb 2017-11-28 09:30:27 -05:00
Simon Glass
73a01d90c0 test: Correct operation when tests pass
When tests pass an error message is printed because of a variable that is
not initialised. Fix this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-11-27 23:05:22 -05:00
Tom Rini
7fef459096 spl: TI: Do not default to SPL_FIT_IMAGE_TINY being enabled
This option prevents booting on am335x_evm at least along with most
likely other platforms.

Fixes: 337bbb6297 ("spl: fit: add SPL_FIT_IMAGE_TINY config to reduce code-size")
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 23:05:11 -05:00
Chris Brandt
11f4678962 usb: r8a66597: Add support for RZ/A series
While the USB HW in the RZ/A is basically the same, there are some
differences from the original versions that were in the SH SoCs.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
2017-11-28 04:06:40 +01:00
Tom Rini
6e6cf015e7 Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 07:22:11 -05:00
Jagan Teki
5451ca4da9 configs: icore-rqs: Enable falcon mode
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
b596df4567 engicam: imx6q: Return mmc dev 0 for icore
icorem6 has sd on usdhci1 which is devno 0 so return proper
devno from board_mmc_get_env_dev for icorem6 and icorem_6rqs

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
52aaddd6f4 i.MX6: engicam: Add imx6q/imx6ul boards for existing boards
Add new board names for existing board support
imx6q - icore and icore_rqs boards
imx6ul - geam6ul and isiot boards

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
539b1e228f board: icore-rqs: Fix mmc get env device
As per USDHC boot eFUSE descriptions:
USDHC3 => devno 2
USDHC4 => devno 3

Linux will detect mmc0, mmc1, mmc2 based on the status
"okay" on usdhc so imx6qdl-icore-rqs.dtsi has enabled
usdhc1, usdhc3 and usdhc4.But U-Boot can detect based
on the aliases so add mmc1, mmc2 for usdhc3 and usdhc4
respectively and return the board_mmc_get_env_dev
by subtracting -1

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
152038ea18 i.MX6UL: icore: Add SPL_OF_CONTROL support
Add OF_CONTROL support for SPL code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
bb0297ccbd pinctrl: imx6ul: Fix pinctrl data overlapped with DT area
before relocation pinctrl data BSS is overlapping DT area,
when .data is using uninitialized global variable,
imx6_pinctrl_soc_info. So assign them flags ZERO_OFFSET_VALID
to prevent BSS overlap

Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
1f6e9bd2a7 i.MX6Q: icore: Add SPL_OF_CONTROL support
Add OF_CONTROL support for SPL code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
a1797beed2 i.MX6Q: icorem6: Move spl load fit to common/spl
Move spl load fit code into common/spl

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
409b16d3e0 i.MX6: engicam: Move set_fdt_file to common
setenv_fdt_file to common code and set dtb based on
CONFIG_DEFAULT_DEVICE_TREE and cpu_type.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Fabio Estevam
f086812acd mx6sxsabresd: Use PARTUUID to specify the rootfs location
mx6sxsabresd can run different kernel versions, such as NXP 4.1 or mainline.

Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the SD
card changes depending on the kernel version.

In order to avoid such issue, use the UUID method to specify the
rootfs location.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2017-11-27 10:35:19 +01:00
Fabio Estevam
e2162d709f imx: Remove boolean parameter from wdog powerdown function
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.

It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.

While at it, rename it to imx_wdog_disable_powerdown().

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-11-27 10:34:49 +01:00
Fabio Estevam
b42287f4c9 imx: Also clear powerdown enable bit for WDOG3 on i.MX6ULL
Clear powerdown enable bit for WDOG3 on i.MX6ULL to avoid unwanted
kernel reboots.

Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-27 10:34:40 +01:00
Fabio Estevam
23ecca2cd8 mx6ull: Fix WDOG3 base address
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-27 10:34:31 +01:00