Commit graph

11 commits

Author SHA1 Message Date
Andrew F. Davis
407a219261 arm: K3: Avoid use of MCU_PSRAM0 before SYSFW is loaded
On HS devices the 512b region of reset isolated memory called
MCU_PSRAM0 is firewalled by default. Until SYSFW is loaded we
cannot use this memory. It is only used to store a single value
left at the end of SRAM by ROM that will be needed later. Save
that value to a global variable stored in the .data section.
This section is used as .bss will be cleared between saving
this value and using it.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-04-26 17:51:51 -04:00
Andreas Dannenberg
3e9b9c1ccd armv7R: K3: am654: Trigger panic on DDR init failures
When initializing DDR from R5 SPL trigger U-Boot's panic facility
rather than simply returning from the board init function as there
is little point continuing code execution. Further, as panic implies
a board reset, so using it might potentially allow to recover from
this error in certain cases such as when the init failure was caused
by a temporary glitch of some sorts.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-04-12 08:05:52 -04:00
Tien Fong Chee
f4b4092474 spl: Kconfig: Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPL_FS_EXT4
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01 09:14:21 -05:00
Tien Fong Chee
0c3a9ed409 spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01 09:12:48 -05:00
Lokesh Vutla
59ebf4afa6 armv7R: K3: am654: Add support for triggering ddr init from SPL
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support
for triggering DDR initialization from board_init_f().

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-11-16 16:51:59 -05:00
Lokesh Vutla
23f7b1a776 armv7R: K3: am654: Enable MPU regions
Enable MPU regions for AM654 evm:
- Region0: 0x00000000 - 0xFFFFFFFF: Device memory, not executable
- Region1: 0x41c00000 - 0x42400000: Normal, executable, WB, Write alloc
- Region2: 0x80000000 - 0xFFFFFFFF: Normal, executable, WB, Write alloc
- region3-15: Disabled

With this dcache can be enabled either in SPL or U-Boot.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-11-16 16:51:58 -05:00
Andrew F. Davis
81089a5430 arm: K3: am654: Add support for getting boot mode
Read the boot mode register to find the boot mode. Only use eMMC boot0
mode when the mode is eMMC boot (called BOOT_DEVICE_MMC1 currently due
to current conflating of boot mode and boot device), and not iff the
boot device is MMC port 0.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-10-10 13:35:08 -04:00
Andrew F. Davis
b5700efbc8 arm: K3: am654: Choose MMC boot device based on boot port
For most devices the boot mode maps directly to the boot
device. For MMC this is not the case as we have two MMC
boot modes and two MMC boot devices (ports). Check the
boot port to determine which MMC device was our boot
device. Make this change for both primary and secondary
boot modes.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-10-10 13:35:08 -04:00
Andreas Dannenberg
c68721d93a arm: K3: am654: Unlock control module registers during init
By default the device control module registers are locked,
preventing any writes to its registers.
Unlock those registers as part of the init flow.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
e00646099f arm: K3: am654: Add support for boot device detection
AM654 allows for booting from primary or backup boot media.
Both media can be chosen individually based on switch settings.
ROM looks for a valid image in primary boot media, if not found
then looks in backup boot media. In order to pass this boot media
information to boot loader, ROM stores a value at a particular
address. Add support for reading this information and determining
the boot media correctly.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
ed0e605124 arm: K3: Add support for AM654 SoC definition
The AM654 device is designed for industrial automation and PLC
controller class platforms among other applications. Introduce
base support for AM654 SoC.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-09-11 08:32:55 -04:00