Recently the FMan Port and MAC compatibles were changed. This patch
aligns the FMan Port and MAC compatibles to the new FMan device tree
binding document. The FMan device tree binding document can be found
in the Linux kernel version 3.18.0, commit
297d35fd2a7d3fbd4e5c0f0c1c18213117ba11ba
./Documentation/devicetree/bindings/powerpc/fsl/fman.txt
This patch doesn't affect legacy compatibles support.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Enable support for ICID setup of qman portals and the required device
tree fixups.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reuse the existing ICID setup code done for LS1046A smmu enablement
and add the equivalent setup for LS1043A chips.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QMan IP block in this SoC is version 3.2 so advertise
this in the SoC configuration header.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Memory reserved for Management Complex needs to be cleaned before any
usage.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012AFRWY supports three board revisions.
Revision A and B board are collectively identified as revA/B,
Revision C board is identifies as revC.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Add ahci compatible support for ls1021a soc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At present the MMC subsystem maintains its own list of MMC devices.
This cannot work with driver model when CONFIG_BLK is enabled, use
blk_dread to replace previous mmc read interface, use
mmc_get_blk_desc to get the mmc device property.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
- Multiples updates to the turris boards / platform
- Changes / enhancements to the Marvell PHY drivers, mainly
to support the turris platform
- Many fixes and enhancements to the pxa3xx NAND driver
- Fixes for the UART boot mode in kwboot
- Misc minor changes to other 32bit and 64bit boards
The Clearfog SOM can optionally have eMMC installed. Enable support for
eMMC boot partitions by default.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support to Armada 7k/8k comphy RX/TX lane swap. The
'phy-invert' DT property defines the inverted signals.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Exclude mvebu commands from SPL builds
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add definitions for CONFIG_ENV_SPI_BUS and CONFIG_ENV_SPI_CS
to Armada-388-GP board configuration
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
For some reason the spi_flash_probe_bus_cs() is called
inside the setup_flash_device() with zero values in place
of configurated SPI flash mode and maximum flash speed.
This code causes HALT error during startup environment
relocation on some platforms - namely Armada-38x-GP board.
Fix the function call by replacing zeros with the appropriate
values - CONFIG_ENV_SPI_MAX_HZ and CONFIG_ENV_SPI_MODE.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
add delay before processing the status flags in pxa3xx_nand_irq().
Signed-off-by: David Sniatkiwicz <davidsn@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
c: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for NAND chips with 8KB page, 4 and 8 bit ECC (ONFI).
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add comments with timing parameter names and some details about
nand layout fileds.
Remove unneeded definition.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Replace the hardcoded value of page chink with value that
depends on flash page size and ECC strength.
This fixes nand access errors for 2K page flashes with 8-bit ECC.
Move the initial flash commannd function assignment past the ECC
structures initialization for eliminating usage of hardcoded page
chunk size value.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add timings and device ID for Toshiba TC58NVG1S3HTA00 flash
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for 2KB page 8-bit ECC strength flash layout
Signed-off-by: Victor Axelrod <victora@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
In the current driver, OOB bytes are accessed in raw mode, and when a
page access is done with NDCR_SPARE_EN set and NDCR_ECC_EN cleared, the
driver must read the whole spare area (64 bytes in case of a 2k page,
16 bytes for a 512 page). The driver was only reading the free OOB
bytes, which was leaving some unread data in the FIFO and was somehow
leading to a timeout.
We could patch the driver to read ->spare_size + ->ecc_size instead of
just ->spare_size when READOOB is requested, but we'd better make
in-band and OOB accesses consistent.
Since the driver is always accessing in-band data in non-raw mode (with
the ECC engine enabled), we should also access OOB data in this mode.
That's particularly useful when using the BCH engine because in this
mode the free OOB bytes are also ECC protected.
Fixes: 43bcfd2bb24a ("mtd: nand: pxa3xx: Add driver-specific ECC BCH support")
Cc: stable@vger.kernel.org
Reported-by: Sean Nyekjær <sean.nyekjaer@prevas.dk>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit is needed to properly support the 8-bits ECC configuration
with 4KB pages.
When pages larger than 2 KB are used on platforms using the PXA3xx
NAND controller, the reading/programming operations need to be split
in chunks of 2 KBs or less because the controller FIFO is limited to
about 2 KB (i.e a bit more than 2 KB to accommodate OOB data). Due to
this requirement, the data layout on NAND is a bit strange, with ECC
interleaved with data, at the end of each chunk.
When a 4-bits ECC configuration is used with 4 KB pages, the physical
data layout on the NAND looks like this:
| 2048 data | 32 spare | 30 ECC | 2048 data | 32 spare | 30 ECC |
So the data chunks have an equal size, 2080 bytes for each chunk,
which the driver supports properly.
When a 8-bits ECC configuration is used with 4KB pages, the physical
data layout on the NAND looks like this:
| 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 64 spare | 30 ECC |
So, the spare area is stored in its own chunk, which has a different
size than the other chunks. Since OOB is not used by UBIFS, the initial
implementation of the driver has chosen to not support reading this
additional "spare" chunk of data.
Unfortunately, Marvell has chosen to store the BBT signature in the
OOB area. Therefore, if the driver doesn't read this spare area, Linux
has no way of finding the BBT. It thinks there is no BBT, and rewrites
one, which U-Boot does not recognize, causing compatibility problems
between the bootloader and the kernel in terms of NAND usage.
To fix this, this commit implements the support for reading a partial
last chunk. This support is currently only useful for the case of 8
bits ECC with 4 KB pages, but it will be useful in the future to
enable other configurations such as 12 bits and 16 bits ECC with 4 KB
pages, or 8 bits ECC with 8 KB pages, etc. All those configurations
have a "last" chunk that doesn't have the same size as the other
chunks.
In order to implement reading of the last chunk, this commit:
- Adds a number of new fields to the pxa3xx_nand_info to describe how
many full chunks and how many chunks we have, the size of full
chunks and partial chunks, both in terms of data area and spare
area.
- Fills in the step_chunk_size and step_spare_size variables to
describe how much data and spare should be read/written for the
current read/program step.
- Reworks the state machine to accommodate doing the additional read
or program step when a last partial chunk is used.
This commit is taken from Linux:
'commit c2cdace755b'
("mtd: nand: pxa3xx_nand: add support for partial chunks")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit simplifies the initial configuration performed
by pxa3xx_nand_scan. No functionality change is intended.
This commit is taken from Linux:
'commit 154f50fbde53'
("mtd: pxa3xx_nand: Simplify pxa3xx_nand_scan")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The Data Flash Control Register (NDCR) contains two types
of parameters: those that are needed for device identification,
and those that can only be set after device identification.
Therefore, the driver can't set them all at once and instead
needs to configure the first group before nand_scan_ident()
and the second group later.
Let's split pxa3xx_nand_config in two halves, and set the
parameters that depend on the device geometry once this is known.
This commit is taken from Linux:
'commit 66e8e47eae65'
("mtd: pxa3xx_nand: Fix initial controller configuration")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The chunk size represents the size of the data chunks, which
is used by the controllers that allow to split transferred data.
However, the initial chunk size is used in a non-split way,
during device identification. Therefore, it must be large enough
for all the NAND commands issued during device identification.
This includes NAND_CMD_PARAM which was recently changed to
transfer up to 2048 bytes (for the redundant parameter pages).
Thus, the initial chunk size should be 2048 as well.
On Armada 370/XP platforms (NFCv2) booted without the keep-config
devicetree property, this commit fixes a timeout on the NAND_CMD_PARAM
command:
[..]
pxa3xx-nand f10d0000.nand: This platform can't do DMA on this device
pxa3xx-nand f10d0000.nand: Wait time out!!!
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x38
nand: Micron MT29F8G08ABABAWP
nand: 1024 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224
This commit is taken from Linux:
'commit c7f00c29aa8'
("mtd: pxa3xx_nand: Increase the initial chunk size")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The read ID count should be made as large as the maximum READ_ID size,
so there's no need to have dynamic size. This commit sets the hardware
maximum read ID count, which should be more than enough on all cases.
Also, we get rid of the read_id_bytes, and use a macro instead.
This commit is taken from Linux:
'commit b226eca2088'
("nand: pxa3xx: Increase READ_ID buffer and make the size static")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
When 2 commands are submitted in a row, and the second is very quick,
the completion of the second command might never come. This happens
especially if the second command is quick, such as a status read
after an erase
This patch is taken from Linux:
'commit 21fc0ef9652f'
("mtd: nand: pxa3xx-nand: fix random command timeouts")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
When the nand is first probe, and upon the first command start, the
status bits should be cleared before the interrupts are unmasked.
This commit is taken from Linux:
'commit 0b14392db2e'
("mtd: nand: pxa3xx_nand: fix early spurious interrupt")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Since the pxa3xx_nand driver was added there has been a discrepancy in
pxa3xx_nand_set_sdr_timing() around the setting of tWP_min and tRP_min.
This brings us into line with the current Linux code.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
