Before Linux boot DPL must be deployed to DPAA2 interface.
So update bootcmd env variable to make sure DPL deployment before
Linux boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define mcinitcmd env variable to load Management complex during
u-boot boot sequence.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported
in SD boot now. For the customer's demand, QSPI needs to be supported
in SD boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig
is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig
is used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Memory controller performance is not optimal with default internal
target queue register value, write required value for optimal DDR
performance.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PAMU driver basic support for usage in Secure Boot.
In secure boot PAMU is not in bypass mode. Hence to use
any peripheral (SEC Job ring in our case), PAMU has to be
configured.
The patch reverts commit 7cad2e38d6.
The Header file pamu.h and few functions in driver have been derived
from Freescale Libos.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The output ring needs to be invalidated before enqueuing the job to SEC.
While allocation of space to output ring, it should be taken care that the
size is cacheline size aligned inorder to prevent invalidating valid data.
The patch also correct the method of aligning end of structs while flushing caches
Since start = align(start_of_struct), it is incorrect to assign
end = align(start + struct_size). It should instead be,
end = align(start_of_struct + struct_size).
Signed-off-by: Saksham Jain <saksham@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Convert ls1021aqds_nor_lpuart and ls1021aqds_ddr4_nor_lpuart
to driver model suport. Enable lpuart port driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Split duart configuration as device tree file. Move /chosen node
out of board commone device tree. Convert ls1021aqds nor and SD
configurations to driver model support (qspi already uses DM).
Enable ns16550 DM serial driver for nor configurations.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
In some case wordlen may not be set. Use SPI_DEFAULT_WORDLEN as default.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
enable dma driver model for am437x_sk_evm as ti-edma3 supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
adopt ti-edma3 driver to device driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
When CONFIG_DMA is defined the default spi_flash_copy_mmap() can
handle dma memory copy, so compile out spi_flash_copy_mmap() from
ti_qspi driver when CONFIG_DMA config is defined.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add dma memcpy api to the default spi_flash_copy_mmap(), so that
dma will be used to copy data when CONFIG_DMA is defined for the
platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add TI_EDMA3 entry on Kconfig with help description.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Implement a DMA uclass so that the devices like ethernet, spi,
mmc etc can offload the data transfers from/to the device and
memory.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add basic framebuffer driver for the S3C24xx family of CPUs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
V2: Keep the Makefile sorted.
Acked-by: Anatolij Gustschin <agust@denx.de>
Zybo contains on board HDMI that's why enable EDID.
Doing it via config because zynq i2c driver hasn't been moved to DM yet
and enabling via Kconfig requires DM_I2C.
This will be moved that driver is moved to DM.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DTS syncup with Linux kernel.
Add missing reset-gpio property.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The problem with current implementation is that SPDDONE bit is 1
but link bit is zero. That's why phydev->link is setup to 0
which ending up in driver failure that link is not up.
Log:
Zynq> dhcp
ethernet@e000b000 Waiting for PHY auto negotiation to complete.......
done
ethernet@e000b000: No link.
There is at least 1ms delay between spddone bit and link up.
Use genphy_read_status() instead of realtek implemenation which is
working with page 11. Linux driver is also using generic implementation.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
reg-offset is the part of standard 8250 binding in the kernel.
It is shifting start of address space by reg-offset.
On Xilinx platform this offset is typically 0x1000.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove the miss-placed \0 and add missing ; for usbboot env variable.
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable u-boot,dm-pre-reloc for qspi for zc706, zed and microzed.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sync logic with Linux kernel where TX empty flag is checked before char
is sent.
This logic is fixing problem with console on zynqmp platform.
For example:
DRAM: 2 GiB
Enabling Caches...
EL Level: �� sdhci@ff170000: 0
Using default environment
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Remove CONFIG_ZYNQ_BOOT_FREEBSD configuration option and setup
CONFIG_SYS_MMC_MAX_DEVICE 1 for all Zynq boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
OF_CONTROL is setup by default and memory reading is done via DT. Remove
all config files with memory references.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove unused macros. Adresses are taken from DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
When the resolution is not supported we should free the memory we don't plan
to use.
Reported-by: Coverity (CID: 135127)
Signed-off-by: Simon Glass <sjg@chromium.org>
In current design, if any peripheral was assigned to both A7 and M4,
it will receive ipg_stop or ipg_wait when any of the 2 platforms
enter low power mode. We will have a risk that, if A7 enter wait,
M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait
asserted same time. Also if M4 enters stop mode, A7 will have no
chance to access the peripheral.
There are 26 peripherals affected by this IC issue:
SIM2(sim2/emvsim2)
SIM1(sim1/emvsim1)
UART1/UART2/UART3/UART4/UART5/UART6/UART7
SAI1/SAI2/SAI3
WDOG1/WDOG2/WDOG3/WDOG4
GPT1/GPT2/GPT3/GPT4
PWM1/PWM2/PWM3/PWM4
ENET1/ENET2
Software Workaround:
The solution is to set the peripherals to Domain0 by A core, since A core
in Domain0. The peripherals which will be used by M4, will be set to Domain1
by M4.
For example, A core set WDOG4 to domain0, but when M4 boots up, M4 will
set WDOG4 to domain1, because M4 will use WDOG4.
So the peripherals are not shared by them. This way requires
the uboot implemented the RDC driver and set the 26 IPs above
to domain 0 only. M4 image will set the M4 to domain 1 and
set peripheral which it will use to domain 1.
This patch enables the CONFIG_IMX_RDC and CONFIG_IMX_BOOTAUX for
i.MX7D SABRESD board, and setup the 26 IP resources to domain 0.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce macros and command to support booting M4 core for
i.MX7D SabreSD board.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up.
arch_auxiliary_core_check_up is used to check whether M4 is running
or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will
use the pc and stack which is set in arch_auxiliary_core_up to set R15
and R13 register and boot.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce macros and command to support booting M4 core for
i.MX6SX SabreSD board.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up.
arch_auxiliary_core_check_up is used to check whether M4 is running
or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will
use the pc and stack which is set in arch_auxiliary_core_up to set R15
and R13 register and boot.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To boot a auxiliary core in asymmetric multicore system, introduce the
new command "bootaux" to do it. Example of boot auxliary core from
0x70000000 where stores the boot head information that should be
parsed by auxiliary core, "bootaux 0x70000000".
Introduce Kconfig option IMX_BOOTAUX.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
