Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base
in simple_strtoul.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Distro boot support gives flexibility to run distro RFS like Ubuntu
being deployed from SD card or SATA drive. If it fails to detect
external storage, fall back to qspi/sd boot.
Enable this by default in RDB's defconfig by selecting
CONFIG_DISTRO_DEFAULTS
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Zhang Ying <zhangying@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently the chipselect used to identify the corresponding NAND chip
is stored at the controller and only set during fsl_ifc_chip_init().
This way, only the last NAND chip is working, as the previous value
of cs_nand gets overwritten.
In order to solve this issue the chipselect is computed on demand by
evaluating the bank variable. Thus, the correct chipselect for each
NAND chip operation is used.
Tested on hardware with two NAND chips connected to the IFC
controller.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Scott Wood <oss@buserror.net>
[YS: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The zero value returned from qbman_swp_acquire() is an error
condition meaning no free buffer for allocation.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kushwaha Prabhakar <prabhakar@freescale.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
This reverts commit c61d0009fe.
A tbs2910 board user reported a very slow console frambuffer as
regression in current u-boot. I could bisect this down to the
above mentioned commit.
This revert brings back the fast framebuffer console (one
cache flush per string in puts(), not after each char).
Reported-by: Uwe Scheffler <scheffler.u@web.de>
Signed-off-by: Soeren Moch <smoch@web.de>
Tested-by: Uwe Scheffler <scheffler.u@web.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The eMMC is 1V8 device only and the signaling is always 1V8,
fix the DT for Salvator-X/XS to describe the hardware correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
After updating u-boot from v2016.01 to 2017.09, issue with
"SATA link 0 timeout." on my Cubietruck board.
mdelay milled after moving satapwr code to board.
"sunxi: Turn satapwr on from board_init"
(sha1: 9fbb0c3aa4)
After adding the "mdelay(500);"
line that was lost in the path the error is gone.
Signed-off-by: Werner Böllmann <Werner.Boellmann@fh-dortmund.de>
[Rebased and updated change and commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Only the H3/H5 SoCs have an internal PHY and its related clock and
reset controls.
Use an #ifdef to guard the internal PHY control code block so it
can be built for other SoCs, such as the A83T or A64.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update the falcon offsets for args to 16MB and kernel to 17MB
Since the below commit updated U-Boot proper location along
with rockchip boot image offsets
"spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip"
(sha1: 8f4d62b403)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch fixed U-Boot proper location has been
missed to update in bewlo commit
"rockchip: doc: update U-Boot location info"
(sha1: 73e6dbe855)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The U-Boot location has been moved to block 16384.
This is 8MB, not 4MB.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
due misnaming of CONFIG_SUN4I_EMAC in include/configs/sunxi-common.h,
likely missed in:
commit 3146f0c017 ("Move PHYLIB to Kconfig")
Signed-off-by: Artturi Alm <artturi.alm@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The following error has been observed on i.MX25 with a high-speed SDSC
card:
Data Write Failed in PIO Mode.
It was caused by the timeout set on PRSSTAT.BWEN, which was triggered
because this bit takes 15 ms to be set after writing the first block to
DATPORT with this card. Without this timeout, all the blocks are
properly written.
This timeout was implemented by decrementing a variable, so it was
depending on the CPU frequency. Fix this issue by setting this timeout
to a long enough absolute duration (500 ms).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When a high speed card is connected to mx51evk the following error is seen:
U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)
CPU: Freescale i.MX51 rev3.0 at 800 MHz
Reset cause: POR
Board: MX51EVK
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX51 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
The i.MX51 ts4800 board already selects this option, but it is better
to move this selection to the i.MX51 SoC level instead.
Successfully tested with a high speed SD card on a mx51evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
When a high speed card is connected to mx25 the following error is seen:
U-Boot 2017.11-rc2-00104-gb79372a (Oct 31 2017 - 11:02:22 -0200)
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR
Board: MX25PDK
I2C: ready
DRAM: 64 MiB
No arch specific invalidate_icache_all available!
MMC: FSL_SDHC: 0
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
, which prevents any usage of the SD card.
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX25 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
Successfully tested with a high speed SD card on a mx25pdk board.
Suggested-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Otavio Salvador <otavio@ossystems.com.br> # mx25pdk
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Use default value 0x4000 for SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR instead
of define a new one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update rockchip U-Boot location to 0x4000/16384.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip use a 'loader2' partition for U-Boot, so u-boot.bin or
u-boot.itb load by SPL need to locate at0x4000. Detail here:
http://opensource.rock-chips.com/wiki_Boot_option
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The environment storage location is selectable via Kconfig. We support
eMMC, SD and SPI-NOR as location for U-Boot. This adds support to store
the environment in the SPI-NOR additional to the default eMMC location.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The VCC_SD and VCC_SDIO rail should only be powered up to 3.0V on RK3399
platforms.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
pinctrl/rockchip.h provides defines that map pin numbers to pin names.
Use them to make the dts more human readable.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This change updates the USB configuration for the RK3399-Q7 in the DTS:
* fixes the OTG board configuration by enabling it ('okay')
* improves the speed of 'usb start' by disabling the unused EHCI/OHCI
controllers
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
To correctly model the usbhub_enable regulator for U-Boot, we need
to change the settings to:
* the GPIO polarity is GPIO_ACTIVE_LOW
* should be set to inactive (enable-active-low) when boot-on settings
are applied
* it can be changed at runtime (i.e. remove the always-on)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The fixed regulator for overriding BIOS_DISABLE had been modelling
backwards (i.e. the GPIO polarity and the enable-active-low/high
property had both been inverted), causing the 'regulator' command
to always print/expect 'disabled'/'enabled' backwards.
This fixes the mix-up and models it correctly:
* the GPIO is low-active
* the regulator should be enabled (enable-active-high) during
boot-on initialisation
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
All Rockchip SoCs use 32KB as CONFIG_ENV_SIZE.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Using the ENV offset from rockchip legacy U-Boot for all SoCs,
the offset is 4MB-32KB
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We use the same default ENV setting in rockchip_common.h for all SoC.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
U-Boot bundles a patched copy of libfdt, so it's wrong to attempt to
include it <like/this>. This breaks the build for me when I have dtc
fully installed in my host -- as happened earlier tonight with
Buildroot, for example.
There are several other occurrences throughout the code where '<libfdt'
matches. I'm not modifying these because I have no clue why the
<systemwide> include style is being used -- IMHO wrongly.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
