Now that we fall back to the FS code path when we don't find u-boot
at the raw sector offset, there is no good reason to not default to
raw boot.
With this patch, I can successfully boot u-boot from a raw sector
offset on beagle-xm.
Signed-off-by: Alexander Graf <agraf@suse.de>
This introduces some minor cleanups, regarding aspects such as board name, code
and headers organization as well as deprecated and missing config options.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The initialization for smmu and stream id is moved into the common soc
code.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Memory controller performance is not optimal with default internal
target queue register value, write required value for optimal DDR
performance.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In current design, if any peripheral was assigned to both A7 and M4,
it will receive ipg_stop or ipg_wait when any of the 2 platforms
enter low power mode. We will have a risk that, if A7 enter wait,
M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait
asserted same time. Also if M4 enters stop mode, A7 will have no
chance to access the peripheral.
There are 26 peripherals affected by this IC issue:
SIM2(sim2/emvsim2)
SIM1(sim1/emvsim1)
UART1/UART2/UART3/UART4/UART5/UART6/UART7
SAI1/SAI2/SAI3
WDOG1/WDOG2/WDOG3/WDOG4
GPT1/GPT2/GPT3/GPT4
PWM1/PWM2/PWM3/PWM4
ENET1/ENET2
Software Workaround:
The solution is to set the peripherals to Domain0 by A core, since A core
in Domain0. The peripherals which will be used by M4, will be set to Domain1
by M4.
For example, A core set WDOG4 to domain0, but when M4 boots up, M4 will
set WDOG4 to domain1, because M4 will use WDOG4.
So the peripherals are not shared by them. This way requires
the uboot implemented the RDC driver and set the 26 IPs above
to domain 0 only. M4 image will set the M4 to domain 1 and
set peripheral which it will use to domain 1.
This patch enables the CONFIG_IMX_RDC and CONFIG_IMX_BOOTAUX for
i.MX7D SABRESD board, and setup the 26 IP resources to domain 0.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up.
arch_auxiliary_core_check_up is used to check whether M4 is running
or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will
use the pc and stack which is set in arch_auxiliary_core_up to set R15
and R13 register and boot.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up.
arch_auxiliary_core_check_up is used to check whether M4 is running
or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will
use the pc and stack which is set in arch_auxiliary_core_up to set R15
and R13 register and boot.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
commit 216d286c7e [imx: mx6: implement
mmc_get_env_dev] introduced selection of the environment device according
to the boot device when booting from SD/MMC.
Extend this functionality for also selecting the device partition.
Signed-off-by: Soeren Moch <smoch@web.de>
The defconfig patch will enable the the SPL and NAND settings.
The update to Kconfig will allow the SPL to configured in and
built.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Implement mmc_get_env_dev, devno can be got from smbr1 of SRC.
Introduce a weak function board_mmc_get_env_dev, different
boards can implement it according to different sdhc controllers
that used by the board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to
match the one in common/env_mmc.c.
Introduce a weak function board_mmc_get_env_dev. Different
boards can implement this according to sdhc controller which
is used by the board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The checking with max frequency supported is not correct, because the temp
is calculated by max pre and post dividers. We can decrease any divider to
meet the max frequency limitation. Actually, the calculation below the codes
is doing this way to find best pre and post dividers.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Wrong checking for the base_addr paramter with LCDIF1 and LCDIF2. Always
enter the -EINVAL return.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.
Signed-off-by: Ye Li <ye.li@nxp.com>
Add DDR3 calibration code for i.MX6Q, i.MX6D and i.MX6DL. This code
fine-tunes the behavior of the MMDC controller in order to improve
the signal integrity and memory stability.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
829520: Code bounded by indirect conditional branch might corrupt
instruction stream.
Workaround: Set CPUACTLR_EL1[4] = 1'b1 to disable the Indirect
Predictor.
833471: VMSR FPSCR functional failure or deadlock.
Workaround: Set CPUACTLR[38] to 1, which forces FPSCR write flush.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
"DISCARD" will remove ._secure.text relocate, but PSCI framework
has already used some absolute address those need to relocate.
Use readelf -t -r u-boot show us:
.__secure_start addr: 601408e4
.__secure_end addr: 60141460
60141140 00000017 R_ARM_RELATIVE
46 _secure_monitor:
47 #ifdef CONFIG_ARMV7_PSCI
48 ldr r5, =_psci_vectors
60141194 00000017 R_ARM_RELATIVE
6014119c 00000017 R_ARM_RELATIVE
601411a4 00000017 R_ARM_RELATIVE
601411ac 00000017 R_ARM_RELATIVE
64 _psci_table:
66 .word psci_cpu_suspend
...
72 .word psci_migrate
60141344 00000017 R_ARM_RELATIVE
6014145c 00000017 R_ARM_RELATIVE
202 ldr r5, =psci_text_end
Solutions:
1. Change absolute address to RelAdr.
Based on LDR (immediate, ARM), we only have 4K offset to jump.
Now PSCI code size is close to 4K size that is LDR limit jump size,
so even if the LDR is based on the current instruction address,
there is also have a risk for RelAdr. If we use two jump steps I
think we can fix this issue, but looks too hack, so give up this way.
2. Enable "DISCARD" only for CONFIG_ARMV7_SECURE_BASE has defined.
If CONFIG_ARMV7_SECURE_BASE is defined in platform, all of secure
will in the BASE address that is absolute.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add code to aid tracking down cache alignment issues.
In case DEBUG is defined in the cache.c, this code will
check alignment of each attempt to flush/invalidate data
cache and print a warning if the alignment is incorrect.
If DEBUG is not defined, this code is optimized out.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
eth_get_dev_by_index() is an API which is not available in driver
model. Use eth_get_dev_by_name() instead, which can also simplifly
the code logic a little bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
QSPI and IFC are pin-multiplexed on LS1043A. So we use
ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and
ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Chain of Trust is enabled for ARM platforms (LS1021 and LS1043).
In board_late_init(), fsl_setenv_chain_of_trust() is called which
will perform the following:
- If boot mode is non-secure, return (No Change)
- If boot mode is secure, set the following environmet variables:
bootdelay = 0 (To disable Boot Prompt)
bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove SECURE_IOU option which is not needed. U-Boot itself can detect
which EL level it is on and based on that use do platform setup.
It also simplify usage because one Kconfig entry is gone.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Banana-pi M3 has LPDDR3 DRAM. this adds support for LPDDR3 for A83T.
Mostly the timing parameters are different from DDR3.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Different A83T boards have different DRAM types. Banapi M3 has LPDDR3,
Allwinner Homlet v1.2 has DDR3.
This adds groundwork to support for new DRAM type for A83T.
Introduce CONFIG_DRAM_TYPE, It'll be 3 for DDR3 and 7 for LPDDR3, must
be set in respective board defconfig.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This removes the redundant lines of code from mctl_sys_init.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
H3 has the same power sequencing procedure as the A31/A31s, which
includes the power clamps.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
H3's CCU includes some switches which disable non-secure access to some
of the more critical clock controls, such as MBUS, PLLs, and main
platform busses.
Configure them to enable non-secure access.
For now the only SoC that has this feature is the H3. For other
platforms just use a default (weak) empty function so things do
not break.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Secure Memory Touch Arbiter is the same thing as the TrustZone
Protection Controller found on A31/A31s.
Access to many peripherals on the H3 can be controlled by the SMTA,
and the settings default to secure access only.
This patch supports the new settings, and sets them to allow non-secure
access.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
LS2080A has support for 8 DPMAC ports out of which
only 5 ports can be used at a time.
Enabling all 8 DPMAC ports of LS2080A personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Updated the default sata register values to enhance the
performance and stability.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SYSCLK frequency is dependent on on-board switch settings. It may
vary as per requirement. boot-loader is aware of board switch
configurations.
So Fixup Linux device tree from boot-loader.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The management data input/output (MDIO) requires open-drain,
i.MX7D TO1.0 ENET MDIO pin has no open drain, but TO1.1 supports
this feature. So to TO1.1, need to enable open drain by setting
bits GPR0[8:7] for TO1.1.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Check "Figure 19-5. BUS clock generation" of i.MX 6SoloX Applications
Processor Reference Manual and "Figure 18-5. BUS clock generation" of
i.MX 6UltraLite Applications Processor Reference Manual. If mmdc clk
sources from pll4_main_clk(pll_audio), the calculation is wrong.
Fix mmdc_ch0 clk calculation. Also add PLL_AUDIO/VIDEO support
for decode_pll.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
To prepare timer driver to DM/DT conversion do not build the
exiting timer driver when CONFIG_TIMER is defined. But since
omap's SPL doesn't support DM yet so built timer driver only for
SPL build when CONFIG_TIMER is defined.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
