Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Platform specific BootROM may use its own image type for loading SPL or
U-Boot proper. In some cases it makes sense to not use BootROM supplied
code for booting U-Boot proper but rather to use U-Boot SPL for this,
e.g. when U-Boot SPL can load U-Boot proper faster than BootROM. In this
case it is required for platform board code to parse and load U-Boot in
BootROM specific image type.
This change adds support for parsing platform / board / BootROM specific
image types via weak function spl_parse_board_header() which is called
before marking boot image as a raw.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Some image types (e.g. kwbimage v1) store the offset to SPL binary and
offset to U-Boot proper binary in their headers. To avoid reading SPL
binary when loading U-Boot proper, add support for specifying offset in
struct spl_image_info, which defines the offset from the beginning of
the header and the beginning of the executable data.
Initial support is added only for SPI, MMC and SATA code. We can extend
it later if needed.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Current code uses hack in board_init_f() which calls return_to_bootrom()
to skip U-Boot SPL code and return back to BootROM to load U-Boot via
UART or from NAND.
This change migrates that hack from the board_init_f() function and
changes it to return BOOT_DEVICE_BOOTROM instead of returning to BootROM
directly, so that U-Boot's SPL framework is used for returning to
BootROM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
U-Boot's SPL framework already has an API for loading U-Boot via
BootROM.
Implement the function board_return_to_bootrom() for mvebu SPL code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
This function does not return, so add the appropriate compiler flag.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Register r0 should be set to return value 0x0 - NO_ERR.
Set r0 with return value after all registers are restored from the
stack, so that the return value is always correct.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 944c7a3176 ("arm: mvebu: Add option to use UART xmodem protocol via kwboot")
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Function image_version() returns unsigned value, so it can never be
negative. Explicitly check for two supported image versions: v0 and v1.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Too small invalid headers may cause kwboot to crash.
Check for header size of v1 images.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Add missing curly brackets for this else statement.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Print trailing newline as the last printed byte can be something
different.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Call tcsetattr() only if the file descriptor is valid. It may be
invalidated by previous lines (if it is not a tty descriptor).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
The 'buf' variable is a pointer and '_buf' is the array itself.
Therefore we should pass sizeof(_buf) instead of sizeof(buf) to read().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
There is no code for extracting data from kwbimage, so show an error
message when user tries this via e.g. dumpimage call:
./tools/dumpimage -T kwbimage -o /tmp/out u-boot-spl.kwb
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Trying to call the following command causes NULL pointer dereference in
strlen():
./tools/dumpimage -T kwbimage -o /tmp/out u-boot-spl.kwb
Fix it by checking whether params->imagename is non-NULL before calling
strlen().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
These structures must have specific size without padding, so mark them as
packed via the de-facto standard macro __packed. Also replace PACKED
macro.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The mkimage host tool can be used to generate kwbimage v1 image with
secure header on host system for A38x plaform also when U-Boot is being
compiled for different platform. So there is no reason to not allow
compiling of mkimage/kwbimage with secure header support for e.g. x86-64
host.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Chris Packham <judge.packham@gmail.com>
This command is supported only by v1 images and specifies a milliseconds
delay after executing some set of DATA commands. The special string value
SDRAM_SETUP instructs BootROM to setup SDRAM controller instead of
executing delay. SDRAM_SETUP may be specified only once and after the
last DATA command.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Chris Packham <judge.packham@gmail.com>
The DATA command is already supported by mkimage for v0 images, but not
for v1 images.
BootROM code which executes v1 images also supports DATA command via an
optional extended v1 header OPT_HDR_V1_REGISTER_TYPE.
Implement support for DATA command for v1 images.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Chris Packham <judge.packham@gmail.com>
The PAYLOAD keyword does nothing. No code is using it and both mkimage
and kwbimage completely ignore it. It looks like a relict from the past.
The payload image itself can be specified only via -d parameter to
mkimage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Chris Packham <judge.packham@gmail.com>
The kwbimage v1 format supports multiple BINARY executable headers.
Add support for it into mkimage/kwbimage tool.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Chris Packham <judge.packham@gmail.com>
Binary header consist of:
* 1 byte for header type
* 3 bytes for header size
* 1 byte for number of arguments
* 3 reserved bytes
* N*4 bytes for arguments
* M bytes (aligned to 4 bytes) for executable data
* 1 byte for information about next header
* 3 reserved bytes
The first four bytes are specified as
sizeof(struct opt_hdr_v1)
and the remaining bytes as
ALIGN(s.st_size, 4) + (binarye->binary.nargs + 2) * sizeof(uint32_t)
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The number is stored in one byte, so the maximum should be 255.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The data part of v1 kwbimage currently contains U-Boot binary prepended
by 64 bytes long Legacy U-Boot image header. This means that the load
address is currently substracted by 64 bytes to ensure that U-Boot's
entry point is at specified execution address.
As mkimage has already separate arguments for load (-a) and execution
(-e) address, there is no need to derive fixed load address from
execution address.
Therefore remove this load address hack from the kwbimage tool and
support generating v1 kwbimage with arbitrary addresses for load and
execution.
Finally, calculate correct load address by caller for mkimage tool in
Makefile. File u-boot-spl.kwb is always a v1 kwbimage and it is the only
v1 kwbimage which U-Boot's build system generates.
Remove also useless overwriting of destaddr for /binary.0 to the value
which is already set on previous lines.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Remove this space, since the constants are indented by tabs.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
The binary header in kwbimage contains executable SPL code.
Print information about this binary header and not only information
about it's data part.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
The data part of v1 images contains 32-bit checksum after the data.
Validate whether this checksum is correct.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Add basic checks for extended headers of v1 images.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Extended header checksum for v0 image is present only in the case when
extended header is present. Skip checksum validation if extended header
is not present.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
In the case when the file name is specified relative to the current
working directory, it does not contain '/' character and strrchr()
returns NULL.
The following strcmp() function then crashes on NULL pointer
dereference.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
SATA and SDIO images must be aligned to sector size (which in most cases
is 512 bytes) and Source Address in main header is stored in number of
sectors from the beginning of the drive. SATA image must be stored at
sector 1 and SDIO image at sector 0. Source Address for PCIe image is
not used and must be set to 0xFFFFFFFF.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Add constant for SDIO value of the bootfrom header field.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Writing into SPI NOR and NAND memory can be done only in 256 bytes long
blocks. Align final image size so that when it is burned into SPI NOR or
NAND memory via U-Boot's commands (sf or mtd), we can use the $filesize
variable directly as the length argument.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
The return value of kwbimage_generate() is used for aligning the data
part of kwbimage. Use it for calculating proper 4 byte alignment as is
required by BootROM and also use it for allocating additional 4 bytes
for the 32-bit data checksum.
This simplifies the alignment code to be only at one place (in function
kwbimage_generate) and also simplifies setting checksum as it can be
directly updated in memory.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
The CONFIG_SYS_U_BOOT_OFFS option may be defined as empty string.
In this case it causes compilation error:
tools/kwbimage.c: In function ‘image_headersz_v1’:
tools/kwbimage.c:1002:39: error: expected expression before ‘)’ token
if (headersz > CONFIG_SYS_U_BOOT_OFFS) {
^
tools/kwbimage.c:1006:41: error: expected expression before ‘)’ token
(int)headersz, CONFIG_SYS_U_BOOT_OFFS);
^
tools/kwbimage.c:1011:35: error: expected expression before ‘;’ token
headersz = CONFIG_SYS_U_BOOT_OFFS;
^
make[1]: *** [scripts/Makefile.host:112: tools/kwbimage.o] Error 1
make: *** [Makefile:1822: tools] Error 2
Check whether the value of CONFIG_SYS_U_BOOT_OFFS is really set.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
The PADCONFIG_202 register (0x02621328) is affected by the locking
of the RSTMUX8 register (0x02620328), and so cannot be configured
in kernel. This has been confirmed as a hardware bug and affects
all K2G SoCs.
Setup the pinmux for this pin before locking the RSTMUX8 register
to allow the ICSS1 PRU1 Ethernet PHY port to work properly. The
workaround was added only for the K2G-ICE board to configure the
pins needed for the PRUSS Ethernet usecase.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726232248.24395-1-s-anna@ti.com
This patch adds the possibility to pass the PIN the OpenSSL Engine
used during signing via the environment variable MKIMAGE_SIGN_PIN.
This follows the approach used during kernel module
signing ("KBUILD_SIGN_PIN") or UBIFS image
signing ("MKIMAGE_SIGN_PIN").
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some builds of squashfs-tools append version string with "-git" or
similar. The float() conversion will fail in this case.
Improve the code to only convert to float() the string before the '-'
character.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joao Marcos Costa <jmcosta944@gmail.com>
With LTO activated, the buildman tools failed with an error on my
configuration (Ubuntu 20.04, stm32mp15_trusted_defconfig) with the error:
../arm-linux-gnueabi/bin/nm:
scripts/gen_ll_addressable_symbols.sh: file format not recognized
It seems the shell variable initialization NM=$(NM) is not correctly
interpreted when shell is started in the Makefile, but I have not this
issue when I compile the same target without buildman.
I don't found the root reason of the problem but I solve it by
providing $(NM) as script parameter instead using a shell variable.
The command executed is identical:
cmd_keep-syms-lto.c := NM=arm-none-linux-gnueabihf-gcc-nm \
u-boot/scripts/gen_ll_addressable_symbols.sh arch/arm/cpu/built-in.o \
.... net/built-in.o >keep-syms-lto.c
cmd_keep-syms-lto.c := u-boot/scripts/gen_ll_addressable_symbols.sh \
arm-none-linux-gnueabihf-gcc-nm arch/arm/cpu/built-in.o \
... net/built-in.o > keep-syms-lto.c
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
*sig_size isn't set until later so use the correct variables.
Signed-off-by: Donald Chan <hoiho@lab126.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At early U-Boot stage, before relocation, MMU is not yet configured
and disabled. DDR may not be configured with the correct memory
attributes (can be configured in MT_DEVICE instead of MT_MEMORY).
In this case, usage of memcpy_{from, to}io() may leads to synchronous
abort in AARCH64 in case the normal memory address is not 64Bits aligned.
To avoid such situation, forbid usage of normal memory cast to (u64 *) in
case MMU is not enabled.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: mark.kettenis@xs4all.nl
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Align reset_cpu function with the next prototypes in
sysreset.h or in cpu_func.h to solve compilation issue:
void reset_cpu(void);
This patch solves the prototype conflict when cpu_func.h is
included.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
These are out of date. Update them and point to the existing build
instructions to avoid duplication. Add a few that are missing.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this driver assumes that ulong is 64-bits long. On 32-bit
machines it is not. Use the 64-bit code only on 64-bit machines.
This makes things work correctly on 32-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
This rule should not be in the top-level Makefile. Now that we have a
consistent set of I2C Kconfigs for U-Boot proper, SPL and TPL, we can move
it.
Make use of the existing SPL/TPL rule in drivers/Makefile instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
