Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
Before proper environment is setup, we extract hwconfig and put it into a
buffer with size HWCONFIG_BUFFER_SIZE. We need to enlarge the buffer to
accommodate longer string. Since this macro is used in multiple files, we
move it into arch/powerpc/include/asm/config.h.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.
To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.
Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block. Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman). However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.
Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely. This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.
Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.
We add support for the following SoCs:
* P1023 - 1 Fman, 2x1g
* P4080 - 2 Fman, each Fman has 4x1g and 1x10g
* P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This converts tsec to use the new PHY Lib. All of the old PHY support
is ripped out. The old MDIO driver is split off, and placed in
fsl_mdio.c. The initialization is modified to initialize the MDIO
driver as well. The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
The Integrated Flash Controller (IFC) is used to access the external
NAND Flash, NOR Flash, EPROM, SRAM and Generic ASIC memories.Four chip
selects are provided in IFC so that maximum of four Flash devices can be
hooked, but only one can be accessed at a given time.
Features supported by IFC are,
- Functional muxing of pins between NAND, NOR and GPCM
- Support memory banks of size 64KByte to 4 GBytes
- Write protection capability (only for NAND and NOR)
- Provision of Software Reset
- Flexible Timing programmability for every chip select
- NAND Machine
- x8/ x16 NAND Flash Interface
- SLC and MLC NAND Flash devices support with
configurable
page sizes of upto 4KB
- Internal SRAM of 9KB which is directly mapped and
availble at
boot time for NAND Boot
- Configurable block size
- Boot chip select (CS0) available at system reset
- NOR Machine
- Data bus width of 8/16/32
- Compatible with asynchronous NOR Flash
- Directly memory mapped
- Supports address data multiplexed (ADM) NOR device
- Boot chip select (CS0) available at system reset
- GPCM Machine (NORMAL GPCM Mode)
- Support for x8/16/32 bit device
- Compatible with general purpose addressable device
e.g. SRAM, ROM
- External clock is supported with programmable division
ratio
- GPCM Machine (Generic ASIC Mode)
- Support for x8/16/32 bit device
- Address and Data are shared on I/O bus
- Following Address and Data sequences can be supported
on I/O bus
- 32 bit I/O: AD
- 16 bit I/O: AADD
- 8 bit I/O : AAAADDDD
- Configurable Even/Odd Parity on Address/Data bus
supported
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.
Eventually this should be handled by Kconfig & defconfigs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1014 is similar to the P1010 processor with the following differences:
- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
* TCP/IP acceleration and classification capabilities
* IEEE 1588 support
* Lossless flow control
* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
software watchdog timer, and four general-purpose timers
* Dual DUARTs
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
The routines boot_ramdisk_high, boot_get_cmdline and boot_get_kbd
are currently enabled by various combinations of CONFIG_M68K,
CONFIG_POWERPC and CONFIG_SPARC.
Use CONFIG_SYS_BOOT_<FEATURE> defines instead.
CONFIG_SYS_BOOT_RAMDISK_HIGH
CONFIG_SYS_BOOT_GET_CMDLINE
CONFIG_SYS_BOOT_GET_KBD
Define these as appropriate in arch/include/asm/config.h files.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Acked-by: Wolfgang Denk <wd@denx.de>
CONFIG_IDE_SWAP_IO
This configuration option replaces a complex conditional
in cmd_ide.c with an explicit define to be added to SoC or
board configs.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p3041 to cpu_type_list and SVR list
* Added number of LAWs for p3041
* Set CONFIG_MAX_CPUS to 4 for p3041
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p5020 & p5010 to cpu_type_list and SVR list
* Added number of LAWs for p5020
* Set CONFIG_MAX_CPUS to 2 for p5020
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers. Merge
this into a single spot.
To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.
In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.
I have done a successful ppc build all and tested a board or two from
each processor family.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_FSL_SEC_COMPAT is set to 2 for the SEC 2.x and SEC 3.x.
Parts with newer SEC h/w versions will increment the number to
accomodate incompatible code changes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
2010-04-21 23:42:38 +02:00
Renamed from arch/ppc/include/asm/config.h (Browse further)
