Original code was assuming that the fuse revision version for all mx53loco boards
based on Dialog PMIC was the same, which is not the case.
Force the revision of all Dialog-based boards to 0.
This fixes a kernel crash when PMIC is accessed in the 2.6.35 kernel
for Dialog rev E boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reduce the environment size (128KB => 16KB) to improve the environment
operations time (e.g. reading, ecc calculation).
Also, remove the unused CONFIG_SYS_ENV_SECT_SIZE.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
We reduce the bootdelay from 10s to 3s to give users a short but usable
window to interrupt the boot process if needed.
Signed-off-by: Tom Rini <trini@ti.com>
- change gpio pin settings:
- gpio pin 6[13] (PLC reset) default value low
- gpio pin 6[0] (TPM reset) default value low
- 4 new GPIO pins
pin i/o name
- 3[9] input Board Type
- 2[7] input HW-ID0
- 2[6] input HW-ID1
- 2[3] input HW-ID2
- read board type and hw id from gpio pins on the enbw_cmc board,
and use board type for setting up different gpio pin settings.
- do not pass "davinci_mmc.use_dma=0" to linux, as MMC now
works with DMA.
- update logbuf support:
store post word in RTC scratch register
- add support for configuring KSZ8864RMN switch through
a config file on u-boot startup. For more infos see:
doc/README.switch_config
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Fix the .dts file USB unit addresses not to duplicate each-other.
Fix the board name string to indicate the vendor is Compulab not NVIDIA.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Walk the BIT and BCT to find the ODMDATA word in the
CustomerData field and put it into Scratch20 reg for
use by kernel, etc.
Built all Tegra builds OK; Booted on Seaboard and saw
ODMDATA in PMC scratch20 was the same as the value in my
burn-u-boot.sh file (0x300D8011). NOTE: All flash utilities
will have to specify the odmdata (nvflash --odmdata n) on
the command line or via a cfg file, or built in to their
BCT.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The SPI hardware on Seaboard is too broken to use; it is muxed with the
console UART and requires evil interactions between the SPI and UART
drivers to work even partially. The current code in U-Boot is not
sufficient to make this work correctly; auto boot is aborted due to
corruption in the UART RX channel interrupting it.
Instead, move the environment to eMMC, at the end of the second boot
sector. This should not conflict with any other eMMC usage, irrespective
of whether the board boots from SPI, NAND, or eMMC: if U-Boot is stored
in eMMC, it will be stored well below this location. The kernel only
uses the general area of the eMMC once booted, not the boot sectors.
Boards that are derivatives of Seaboard don't have the muxing issue,
and should/could have a separate U-Boot configuration file that does
enable SPI if desired.
Alternatively, the environment could be stored in NAND flash, but we
currently have no driver for that controller.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, start removing/renaming
Tegra2-specific files. No functional changes (yet).
Also updated copyright to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.
Note: This assumes the user plugged the standard 8MB MoviNAND card into
J29/HSMMC/POP. If they didn't, the boot sector layout may be different.
However, use of that particular card is standard practice as far as I
know.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a device tree for Ventana; the Seaboard file no longer represents
the HW present on Ventana.
Enable USB on Ventana.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The SMSC95xx series may exist either directly on a main board, or as a USB
to Ethernet dongle. However, dongles containing these chips are very rare.
Hence, remove this config option, except on Harmony where such a chip is
actually present on the board.
The asix option remains, since it's a popular chip, and I actively use a
dongle containing this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
... to enable USB host support, which enables Ethernet support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
... to enable USB host support, which enables Ethernet support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_CMD_PING/NFS aren't required for Whistler to boot.
Add some comments.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This implements a useful bootcmd for Tegra. The boot order is:
* If USB enabled, USB storage
* Internal MMC (SD card or eMMC)
* If networking is enabled, BOOTP/TFTP
When booting from USB or MMC, the boot script is assumed to be in
partition 1 (although this may be overridden via the rootpart variable),
both ext2 and FAT filesystems are supported, the boot script may exist
in either / or /boot, and the boot script may be named boot.scr.uimg or
boot.scr.
When booting over the network, it is assumed that boot.scr.uimg exists
on the TFTP server. There is less flexibility here since those setting
up network booting are expected to need less hand-holding.
In all cases, it is expected that the initial file loaded is a U-Boot
image containing a script that will load the kernel, load any required
initrd, load any required DTB, and finally bootm the kernel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
console isn't used by anything, and the kernel should be set appropriately
by whatever script is booting the kernel, not imposed by the bootloader.
mem might be useful, but the current value is pretty bogus, since it
includes nvmem options that make no sense for an upstream kernel, and
equally should not be required for any downstream kernel. Either way, this
is also best left to the kernel boot script.
smpflag isn't used by anything, and again was probably intended to be a
kernel command-line option better set by the kernel boot script.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a new command "sysboot" which parses syslinux menu files and boots
using kernel and initrd specified by menu files. The operation is similar
to "pxe boot" except local files on ext2 or fat filesystem are parsed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.
Signed-off-by: Tom Rini <trini@ti.com>
If the testpin is asserted, first check if a test_bank
variable is defined before trying to boot this
test_bank.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
kmcoge5ne starts the post tests if the testpin on
the board was enabled. Currently it does simply a memory
test.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Increase bootlimit to 3 to be more tolerant during the
boot process before switching to the backup application.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This board is a MPC8360 board. Two flashes are present
a NOR flash were u-boot and the u-boot environment is stored
and a NAND flash for the application code. This board has 512MB
SDRAM.
Additionaly we introduce a common km8360.h file and convert kmeter1 to
use this.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support for a second flash.
By default, a single flash chip is set up:
- called 'boot'
- mtd name for ubi 'ubi0'
MTDIDS and MTDPARTS may be overwritten to add a second flash.
The 'ubiattach' command is featured in two versions:
- if CONFIG_KM_UBI_PARTITION_NAME_APP is not defined:
this is the version as up to now
- if CONFIG_KM_UBI_PARTITION_NAME_APP is defined:
a check on 'actual_bank' will be done to determine the flash to boot
from.
Use CONFIG_KM_UBI_PARTITION_NAME_BOOT and
CONFIG_KM_UBI_PARTITION_NAME_APP to define where to put the bootloader
and the applications.
Example:
In the board config do:
... snip ...
"boot:" \
"768k(u-boot)," \
"128k(env)," \
"128k(envred)," \
"-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" \
"app:" \
"-(" CONFIG_KM_UBI_PARTITION_NAME_APP ");"
... snap ...
You may also need to enable the second flash:
... snip ...
/* additional featured for COGE5 */
... snap ...
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We don't use PCI on kmeter1 and never will be, so remove some
unneeded code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This additional header is unneeded, we can use the tuxx1.h for this
target.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The malloc buffer is not large enough to hold a flash sector (0x20000 bytes)
in addition to whatever else it normally holds, so double its size. This
fixes a failure trying to save the environment:
=> save
Saving Environment to Flash...
Unable to save the rest of sector (122880)
. done
Protected 1 sectors
This problem probably surfaced from some other change that significantly
increased the normal memory usage, thereby not leaving enough room for
the saveenv command.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 'master' of git://git.denx.de/u-boot-video:
video: atmel/lcd: add LCD driver for new Atmel SoC
video: cfb_console: flush dcache for frame buffer in DRAM
cfb_console: Ignore bell character
cfb_console: Add console_clear_line function
cfb_console: Fix function console_back
omap3_dss: cosmetic changes
omap3_dss: add optional framebuffer
mx53loco: Add LCD support
mx5: Rename mx51_fb_init()
mx53: Allow IPUv3 driver to also work on mx53
mx51evk: Add LCD support
EXYNOS: display 32bpp bitmap TIZEN logo
create lib/tizen directory
LCD: display 32bpp decompressed bitmap image
common/lcd.c: reduce one CONFIG_LCD_LOGO ifdef
common/lcd.c: reduce some CONFIG_LCD_*_LOGO ifdefs
common/lcd.c: use ARRAY_SIZE
cmd_bmp.c: make bmp_display() usable by drivers or board code
LCD: support another s6e8ax0 panel type
LCD: change s6e8ax0 panel gamma value
include/video.h: drop unused video_printf()
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-mips:
MIPS: board.c: move extern declarations to u-boot-mips.h
MIPS: bootm_qemu_mips.c: make checkpatch.pl clean
MIPS: bootm.c: make checkpatch.pl clean
Signed-off-by: Wolfgang Denk <wd@denx.de>
The new Atmel SoC (at91sam9x5 series and at91sam9n12) add a totally
different LCD controller. Add this new driver to support it.
Using CONFIG_ATMEL_HLCD (distinguish with CONFIG_ATMEL_LCD) to enable
this in board configuration file.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This is an sh2a device (max 266MHz) with FPU, video display
controller (VDC), 8 serial ports, 4 I2C channels, 3 CAN ports,
SD and on-chip USB.
The RSK2+SH7269 board uses the SH7269 processor. It is often
referred to as just rsk7269.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The board with sh_eth needs to set CONFIG_SH_ETHER_PHY_MODE.
And SH7734 needs to set value of CONFIG_SH_ETHER_SH7734_MII.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The AP-SH4A-4A board has SH7734, 64MB DDR2-SDRAM, USB,
Ethernet, and more.
This patch supports the following functions:
- 64MB DDR2-SDRAM
- 16MB NOR Flash memory
- Serial console (SCIF)
- Ethernet (SH-Ether with Gigabit)
- I2C
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
