The echo -ne "\xNN" does not work in certain bourne-compatible shells, like
dash. The recommended way of hex->char conversion is using printf(1), but
there is a pitfall here. The GNU printf does support "\xNN" format, but
according to the opengroup documentation, this is not part of POSIX. The
POSIX printf only defines "\NNN" where N is octal. Thus, for the sake of
compatibility, we use that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The current code in ARMv8's lowlevel_init() skips the per-CPU GIC
initialization ifndef CONFIG_ARMV8_MULTIENTRY. However, the per-CPU init
should always occur; it's just the one-time init that should only happen
on the master.
Once this consideration is taken into account, the only difference between
the paths when CONFIG_ARMV8_MULTIENTRY is undefined/defined is the use of
branch_if_slave. Naively, any unified code would need to invoke this
conditionally upon ifdef CONFIG_ARMV8_MULTIENTRY. However, branch_if_slave
already checks CONFIG_ARMV8_MULTIENTRY and does nothing if it isn't
defined, so we don't even need that ifdef at the call site.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
commit 62c5674ea1 ("omap: SPL boot devices cleanup and completion")
cleans up the boot device ids for amx3xx soc. But mistakenly updates wrong
device IDs for AM43xx USB. Fixing the same here.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In DRA72x and AM57xx EVMs the card detect gpio is designed as
active low gpio. So correcting the dt card detect gpio
definition.
Also adding card-detect gpio for DRA74x EVM.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM43xx the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move all the gpio definitions to driver file as
there is no use of them in other files.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove non driver model support as it moved
to driver model. Dont need non driver model
anymore.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable DM GPIO and ZYNQ GPIO using kconfig instead of the board
config file.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are mini configurations which need to be fit to OCM that's why
these options shouldn't be enabled by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds the sata port phy OOB timing values in the sata
device-tree node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline kernel has no r1p12 compatible string that's why console stops
to work with the latest DTS files. Append generic compatible string.
Keep in your mind that using this generic compatible string not all uart
features will be available.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modifying device tree node to support legacy interrupts.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Ravi Kiran Gummaluri <rgummal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
GPIO driver supports an input interrupt that's why gpio node itself can
be labeled as interrupt controller.
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds ddrc memory controller node in dts.
size mentioned in dts is 0x30000, because we need to access DDR_QOS
INTR registers located at fd090208 from this driver.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP DMA's main clock and apb clock are added
in zynqmp DT.
Signed-off-by: VNSL Durga <vnsldurg@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
ZynqMP is not using global interrupt-parent setting that's why
it has to be listed in every node separately. PMU node missed it and
this patch is adding it.
Reported-by: John Linn <John.Linn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add power-domains to the DT and attach devices to them.
The power-domains are all logical domains as understood by firmware.
Each PD is identified by a unique identifier that the platform firmware
understands.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds broken-tuning property to SD and
eMMC nodes.
Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove jumbo properties which are handled in the driver directly
and use mainline compatible string which is already handled by the
driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add 8-bit bus width property to eMMC node.
Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch makes compatible string as "m25p80" for qspi node in
ep108 device tree file
Signed-off-by: Ranjit Waghmode <ranjit.waghmode@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all ZynqMP device trees inline
with each other.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing adv7511 and configure to match Base TRD.
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Reviewed-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Have compatible string as the first property
- Sync with Linux kernel dtsi
- Add missing interrupt properties
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added addtional bindings required for FPGA Manager operation
of the Xilinx Zynq Devc configuration interface.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
GPIO driver supports an input interrupt that's why gpio node itself can
be labeled as interrupt controller.
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
its Kconfig conversion it has ended up missing on some recently
added boards.
Simply select it for ARCH_SUNXI, so that we get it on all
sunxi boards for both a consistent user experience and simpler
defconfig files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
DLDO3 is used to provide Port-D power and PD is used for the
usb-hub / sata-5v enable pins. The 2.5V comes from the schematic
and matches the factory image fex file.
The dts changes are the minimal changes needed for u-boot to
pick-up the usb host controllers. The upstream kernel does not
(yet) have usb host support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some boards have on board usb devices which need longer than the USB
spec's 1 second to connect from board powerup. Add a config option which
when non 0 adds an extra delay before the first usb bus scan.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
v7_maint_dcache_all() does not work reliable when build with gcc6,
see: https://bugzilla.redhat.com/show_bug.cgi?id=1318788
While debugging this I learned that v7_maint_dcache_all() is unreliable
when build with gcc5 too when it is marked as noinline.
This commit fixes the reliability issues by replacing the C-code with
the ready to use asm implementation from the kernel.
Given that this code when written as C-code clearly is quite fragile
(also see the existing comments about the C-code being the way it is
to get optimal assembly) and that we have a proven asm alternative,
I believe that this is the best solution.
Note that we actually already had a copy of the kernel's
v7_flush_dcache_all() before this commit in
arch/arm/mach-uniphier/arm32/lowlevel_init.S.
This commit moves that code arch/arm/cpu/armv7/cache_v7_asm.S, renames
it to __v7_flush_dcache_all(), and adds a v7_flush_dcache_all() wrapper
which saves / restores the clobbered registers for use from C-code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that rpi_*defconfig and Kconfig (rather than the config header file)
provide the identity of the build, we don't need to separate config
headers and board directories for each RPi variant. Set CONFIG_SYS_BOARD
and CONFIG_SYS_CONFIG_NAME so that we can get rid of the duplication. This
requires a tiny number of extra ifdefs in the config header.
The only disadvantage of this approach is that the $board/$board_name
environment variables aren't as descriptive as they used to be. This isn't
really an issue because those only exist to allow scripts to create DTB
filenames at runtime. However, the RPi board code already sets $fdtfile to
something more accurate based on FW-reported board ID anyway.
While at it, unify some Kconfig select options, and add a MAINTAINERS
entry for bcm283x too.
Partially-suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add notes re: enabling the UART to the RPi 3 32-bit help text. Fully
describe the RPi 3 64-bit board option.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
On all Pis so far, the VC FW provides a short stub to set up the ARM CPU
before entering the kernel (a/k/a U-Boot for us). This feature is not
currently supported by the VC FW when booting in 64-bit mode. However,
this feature will likely appear in the near future, and this U-Boot port
assumes that such a feature is in place. Without that feature, or a
temporary workaround described below, U-Boot will not boot.
Once the VC FW does provide the ARM stub, u-boot.bin built for rpi_3 can
be used drectly as kernel7.img, in the same way as any other RPi port. The
following config.txt is required:
# Fix mini UART input frequency, and setup/enable up the UART.
# Without this option, U-Boot will not boot, even if you don't care
# about the serial console. This option will always be required for
# all RPi3 use-cases, unless the PL011 UART is used, which is not
# yet supported by rpi_3* builds of U-Boot.
enable_uart=1
# Boot in AArch64 (64-bit) mode.
# It is possible that a future VC FW will remove the need for this
# option, instead auto-setting 32-/64-bit mode based on the "kernel"
# filename present on the SD card.
arm_control=0x200
Prior to the VC FW providing the ARM boot stub, you can use the following
steps to build an equivalent stub into the U-Boot binary:
git clone https://github.com/swarren/rpi-3-aarch64-demo.git \
../rpi-3-aarch64-demo
(cd ../rpi-3-aarch64-demo && ./build.sh)
Build U-Boot for rpi_3 in the usual way
cat ../rpi-3-aarch64-demo/armstub64.bin u-boot.bin > u-boot.bin.stubbed
Use u-boot.bin.stubbed as kernel7.img on the Pi SD card.
In this case, the following additional entries are required in config.txt:
# Tell the FW to load the kernel image at address 0, the reset vector.
kernel_old=1
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are ARM SoCs (such as the BCM2837) do not contain an ARM GIC. Fix
the ARMv8 CPU startup code to compile in this case.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The dwmmc.h include was forgotten during the migration of dwmmc
probing to DM. Since the shiny DM is in place now, remove this
relic of the past.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Thus far, the socfpga init code had hard-coded the configuration
of the ethernet PHY interface to RGMII in the ethernet registers
in sysmgr space, so PHYs connected in another modes did not work.
This patch fixes support for configurations where the ethernet PHYs
are connected over MII/GMII/RMII interfaces by parsing the phy-mode
OF property of the GMACs and configuring the ethernet registers in
sysmgr space accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Denis Bakhvalov <denis.bakhvalov@nokia.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
ARM defines __raw_writes[bwql], __raw_reads[bwql] in arch io.h
but not the writes[bwql], reads[bwql] needed by some drivers.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch aims to fix the order of CSU slave index for the LS1021a
board.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When switching between the early and final mmu tables, the stack will
get corrupted if the Non-Secure attribute is different. For ls1043a,
this issue is currently masked because flush_dcache_all is called
before the switch when CONFIG_SYS_DPAA_FMAN is defined.
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently only chip-select 0 is supported by the kirkwood SPI driver.
The Armada XP / 38x SoCs also use this driver and support multiple chip
selects. This patch adds support for multiple CS on MVEBU.
The register definitions are restructured a bit with this patch. Grouping
them to the corresponding registers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This option enable adding new platform suport just by adding defconfig
and DTS file which will target generic configuration for SoC.
Make no sense to extend Kconfig just create a pointer between DTS and
configuration file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.
Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Armada 375 still has some problems with d-cache enabled in the ethernet
driver (mvpp2). So lets keep the d-cache disabled until this is solved.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the Marvell A375 eval board. Tested
are the following interfaces:
- I2C
- SPI
- SPI NOR
- Ethernet (mvpp2), port 0 & 1
Currently the A375 SerDes and DDR3 init code is not intergrated. So
the SPL U-Boot is not fully functional.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the Armada 375. Please note that
currently the SerDes and DDR3 init code for the A375 is not
included / enabled. This will be done in a later, follow-up patch.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This commit add support for 96Boards Dragonboard410C.
It is board based on APQ8016 Qualcomm SoC, complying with
96boards specification.
Features (present out of the box):
- 4x Cortex A53 (ARMv8)
- 2x USB Host port
- 1x USB Device port
- 4x LEDs
- 1x HDMI connector
- 1x uSD connector
- 3x buttons (Power, Vol+, Vol-/Reset)
- WIFI, Bluetooth with integrated antenna
- 8GiB eMMC
U-Boot boots chained with fastboot in 64-bit mode.
For detailed build instructions see readme.txt in board directory.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
First supported chip is APQ8016 (that is compatible with MSM8916).
Drivers in SoC code:
- Reset controller (PSHOLD)
- Clock controller (very simple clock configuration for MMC and UART)
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This moves the sniper board from the lge to lg, in order to match the devicetree
vendor prefix already defined in the kernel.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The default board_init_f() implementation performs a call to
board_init_r() as the last step of the sequence. Fix the comment
for this function to reflect the actual execution flow.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with
the CPU complex swapped out for a quad-core ARMv8. This can operate in 32-
or 64-bit mode. 32-bit mode is the current default selected by the
VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of
U-Boot for the Raspberry Pi 3.
>From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a
change in usage of the SoC UARTs. On all previous Pis, the PL011 was the
only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a
UART to connect to the SoC. By default, the PL011 is used for this purpose
since it has larger FIFOs than the other "mini" UART. However, this can
be configured via the VideoCore firmware's config.txt file. This patch
hard-codes use of the mini UART in the RPi 3 port. If your system uses the
PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot
port instead. A future change might determine which UART to use at
run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed
together.
The mini UART has some limitations. One externally visible issue in the
BCM2837 integration is that the UART divides the SoC's "core clock" to
generate the baud rate. The core clock is typically variable, and under
control of the VideoCore firmware for thermal management reasons. If the
VC FW does modify the core clock rate, UART communication will be
corrupted since the baud rate will vary from the expected value. This was
not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To
work around this, the VideoCore firmware can be told not to modify the SoC
core clock. However, the only way this can happen and be thermally safe is
to limit the core clock to a low/minimum frequency. This leaves
performance on the table for use-cases that don't care about a UART
console. Consequently, use of the mini UART console must be explicitly
requested by entering the following line into config.txt:
enable_uart=1
A recent version of the VC firmware is required to ensure that the mini
UART is fully and correctly initialized by the VC FW; at least
firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on
core clock See: https://github.com/raspberrypi/firmware/issues/572".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds an explanation of which Raspberry Pi models each target option
supports.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
MSMC segment Privilege ID is not consistent accross the keystone2 SoCs.
As the first step to ensure complete SoC wide coherency setup, lets
refactor the macros to remove the #if-deffery around the code which
obfuscates which IDs are actually enabled for which SoC.
As a result of this change the PCIe configuration is moved after the
msmc configuration is complete, but that should ideally have no
functional impact.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Move most of the flags required into LLVM_RELFLAGS to test at build
time instead of requiring them to be passed in.
- Update doc/README.clang to reflect this
- Switch to rpi_2 as the example as it's closer to working out of the
box than rpi is.
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of
running AArch64 code and thus is the first of its kind for the sunxi target.
This patch adds a defconfig and device tree chunks for it.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: Change patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.
Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some parts of the sunxi code cast explicitly between u32 values and pointers.
This is not a problem in practice, because all 64bit SoCs today only use the
lower 32 bits for their phyical address space. But we need to make sure that
the compiler is sure this is not an accident as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We currently depend SPL config options on specific machine types which doesn't
scale. Fortunately there's already a kconfig variable that tells us whether we
want to build SPL code at all, so just depend them on this.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some of the code in arch/arm/cpu/armv7/sunxi is actually armv7 specific, while
most of it is just generic code that could as well be used on an AArch64 SoC.
Move all files that are not really tied to armv7 into a new mach-sunxi
directory.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This provides the minimal changes to the H8Homlet v2 dts to enable USB
in U-boot. It is not what will be submitted to the kernel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This provides the minimal changes to the Cubietruck Plus dts to enable USB
in U-boot. It is not what will be submitted to the kernel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This provides the minimal changes to the A83T dtsi to enable USB in
U-boot. It is not what will be submitted to the kernel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
