The GMAC in the RK3399 is very similar to the RK3288 variant (i.e. it
is a Designware GMAC core and requires similar configuration as the
RK3288 to switch it to RGMII and set up the TX/RX delays for Gigabit).
The key difference is that the register offsets (within the GRF block)
and bit-offsets (within those registers) used to hold the configuration
differ between the various RK32/33 CPUs.
This change refactors the gmac_rockchip.c driver to use a function
table (selected via driver_data) to factor out these differences. Each
function's implementation then matches the underlying processor.
Some collateral changes are needed in the definitions describing the
bits and offsets in the GRF are needed to prefix each set of symbolic
constants with the SoC name to avoid name clashes... and in doing so,
the shifts for masks and constants have been moved into the header
files for readability (and to make it easier to stay below 80 chars).
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed commit message typo s/factor our/factor out/:
Signed-off-by: Simon Glass <sjg@chromium.org>
To add GMAC (Gigabit Ethernet) support (limited to RGMII only at this
point), we need support for additional pin-configuration. This commit
adds the pinctrl support for GMAC in RGMII signalling mode:
* adds a PERIPH_ID_GMAC and the mapping from IRQ number to PERIPH_ID
* adds the required defines (in the GRF support) for configuring the
GPIOC pins for RGMII
* configures the RGMII pins (in GPIOC) when requested via pinctrl
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
An earlier upstream change contained an unconditional debug message
which would show up as a message similar to the following in the
U-Boot startup (after the ATF and before the U-Boot banner):
time 159f019, 0
This commit removes this message (instead of making if conditional on
being a debug-build), as it doesn't pertain to any initialisation done
in this file.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Designware HDMI controller and phy are used in other SoCs as well. Split
out platform independent code.
DW HDMI has 8 bit registers but they can be represented as 32 bit
registers as well. Add support to select access mode.
EDID reading code use reading by blocks which is not supported by other
SoCs in general. Make it more general using byte by byte approach, which
is also used in Linux driver.
Finally, not all DW HDMI controllers are accompanied with DW HDMI phy.
Support custom phys by making controller code independent from phy code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The armclk starts in slow mode (24MHz) on the rk3188, which results in U-Boot
startup taking a lot of time (U-Boot itself, but also the rc4 decoding done
in the bootrom).
With default pmic settings we can always reach a safe frequency of 600MHz
which is also the frequency the proprietary loader left the armclk at,
without needing access to the systems pmic.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The armclk starts in slow mode (24MHz) on the rk3188, which makes the whole
startup take a lot of time. We therefore want to at least move to the safe
600MHz value we can use with default pmic settings.
This is also the freqency the proprietary sdram-init leaves the cpu at.
For boards that have pmic control later in u-boot, we also add the option
to set the maximum frequency of 1.6GHz, if they so desire.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
In the beginning, we did SPL -> TPL -> U-Boot, but after clarification
of the real ordering swapped SPL and TPL.
It seems some renames were forgotten and may confuse future readers, so
also swap these to reflect the actual ordering.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
There was still a static ram value set in the rk3188-board from the
time where we didn't have actual sdram init code.
Now the sdram init leaves the ram information in SYS_REG2 and we can
decode it similarly to the rk3288.
Right now we have two duplicates of that code, which is still ok and
doesn't really count as common code yet, but if we get a third copy
at some point from a newer soc, we should think about moving that to
a more general position.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Right now we're setting the wrong value of 0 as base in the ram_info struct,
which is obviously wrong for the rk3188. So instead set the correct value
we already have in CONFIG_SYS_SDRAM_BASE.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Commit c67c8c604b ("board_init.c: Always use memset()") dropped the naive
memset alternative from board_init_f_init_reserve.
So activate CONFIG_TPL_LIBGENERIC for that common memset implementation.
We cannot use the ARCH-specific memset, as that would incur 200bytes of
additional TPL size, space we do not have.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SPL binary needs to be prefixed with the boot magic ('RK33' for
the RK3399) on the Rockchip platform and starts execution of the
instruction word following immediately after this boot magic.
This poses a challenge for AArch64 (ARMv8) binaries, as the .text
section would need to start on the odd address, violating natural
alignment (and potentially triggering a fault for any code that
tries to access 64bit values embedded in the .text section).
A quick and easy fix is to have the .text section include the 'RK33'
magic and pad it with a boot0 hook to insert 4 bytes of padding at the
start of the section (with the intention of having mkimage overwrite
this padding with the appropriate boot magic). This avoids having to
modify the linker scripts or more complex logic in mkimage.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
This includes Marvell mvpp2 patches with the ethernet support for the
ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe
and he is okay with me pushing them via the Marvell tree.
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds board support for the Toradex Apalis TK1 a computer on
module which can be used on different carrier boards.
The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot, environment storage and Toradex factory config block
- Gigabit Ethernet
- MMC/SD cards (both MMC1 as well as SD1 slot)
- USB client/host (dual role OTG port as client e.g. for DFU/UMS or host,
other two ports as host)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Even though we expect only master core to execute U-Boot code
let's make sure even if for some reason slave cores attempt to
execute U-Boot in parallel with master they get halted very early.
If platform wants it may kick-start slave cores before passing control
to say Linux kernel or any other application that want to see all cores
of SMP SoC up and running.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The default configuration for the COMPHY-0 port should be 1G, as its
used as 1G SGMII connection. This change is necessary to get the
MAC2 port (SGMII) working on this DB.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds the description of the PPv2.2 hardware block for the
Marvell Armada 7K and Armada 8K processors, and their corresponding Armada
7040 and 8040 Development boards.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit replaces legacy timer code with usage of arc timer
driver.
It removes arch/arc/lib/time.c file and selects CONFIG_CLK,
CONFIG_TIMER and CONFIG_ARC_TIMER options for all ARC boards by default.
Therefore we remove CONFIG_CLK option from less common axs101 and
axs103 defconfigs.
Also it removes legacy CONFIG_SYS_TIMER_RATE config symbol from
axs10x.h, tb100.h and nsim.h configs files as it is no longer required.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We want to use the same device tree blobs in both Linux and U-Boot for
ARC boards.
Earlier device tree sources in U-Boot were very simplified and hadn't been
updated for quite a long period of time.
So this commit is the first step on the road to unified device tree blobs.
First of all we re-organize device tree sources for AXS10X boards.
As AXS101 and AXS103 boards consist of AXS10X motherboard and AXC001 and
AXC003 cpu tiles respectively we add corresponding device tree source
files: axs10x_mb.dtsi for motherboard, axc001.dtsi and axc003.dtsi for
cpu tiles and axs101.dts and axs103.dts to represent actual boards.
Also we delete axs10x.dts as it is no longer used.
One more important change - we add timer device to ARC skeleton device
tree sources as both ARC700 and ARCHS cores contain such timer.
We add core_clk nodes to abilis_tb100, nsim, axc001 and axc003 device tree
sources as it is referenced via phandle from timer node in common
skeleton.dtsi file.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Tests have shown that on some boards the default width of the
configuration pulse for the PEX link detection might lead to
non-established PCIe links (link down). Especially under certain
conditions (higher temperature) and with specific PCIe devices
(in the case on the theadorable board its a Atheros PCIe WLAN
device). To enable a board-specific detection pulse width this weak
array "serdes_pex_pulse_width[4]" is introduced which can be
overwritten if needed by a board-specific version. If the board
code does not provide a non-weak version of this variable, the
default value will be used. So nothing is changed from the
current setup on the supported board.
Many thanks to Adam from Marvell for all his insights here and
his suggestion about testing with a changed detection pulse width.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Adam Shobash <adams@marvell.com>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add pin control nodes for North and South bridges to
Armada-37xx DT
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added A8040 dts file for community board MACCHIATIBin.
The patch includes the following features:
AP - Serial console (connected to onboard FTDI usb to serial)
CP0 - PCIe x4, SATA, I2C and 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy)
CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy),
SGMII connected to onboard 1512 1Gbps copper phy,
and additional SGMII connected to SFP
(default 1Gbps can be configured to 2.5Gbps).
Network interface naming -
egiga0 - CP0 KR
egiga1 - CP1 KR
egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot)
egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Layerscape Chassis-2 have PCIe device, some platform devices and
DPAA1 devices which will use stream-ids for iommu level isolation
as they are behind SMMU.
This patch defines the stream-ids for Chassis-2 devices. DPAA1 is
reserved for future use.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080a, LS1088a and LS2088a SOCs are based on Chassis-3 and shared
same stream-id partitioning. This patch rewords the definition to
support all these SOCs.
Also have changes in description about iommu-map property updates
in PCI node.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The stream ID allocation for Chasis 3.0 devices can be shared among
LS1088, LS2088 and LS2080.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
USB requires 100MHz clock. On LS1012A, a dedicated 100MHz is provided
instead of SYSCLK (125MHz). Skipping checking SYSCLK for FDT fixup.
Signed-off-by: Yingxi Yu <yingxi.yu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS2088A series SoCs has different physical memory map address and
CCSR registers address against LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This i2c errata only applies to LS2080A and its variants, namely
LS2080A, LS2085A and LS2088A.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SerDes information is not necessary to be present in RCWSR29 register.
It may vary from SoC to SoC.
So Avoid RCWSR28 register hard-coding.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A009635 is valid only for LS2080A SoC and its
personality. Add SoC svr check.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For validating images from uboot (Such as Kernel Image), either keys
from SoC fuses can be used or keys from a verified table of public
keys can be used. The latter feature is called IE Key Extension
Feature.
For Layerscape Chasis 3 based platforms, IE table is validated by
Bootrom and address of this table is written in scratch registers 13
and 14 via PBI commands.
Following are the steps describing usage of this feature:
1) Verify IE Table in ISBC phase using keys stored in fuses.
2) Install IE table. (To be used across verification of multiple
images stored in a static global structure.)
3) Use keys from IE table, to verify further images.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moved the ifdef into ppa.h and removed the duplicated macros.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add header address for PPA to be validated during ESBC phase for LS2080A
platform based on Layescape Chasis 3.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since the lpc32xx i2c driver does not yet support the devicetree bindings,
this structure is also needed by the board file as the hardware description
is done there.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
