If we change to software ecc and then back to hardware ecc, the nand ecc ops
pointers are populated with incorrect function pointers. This is related to the
way nand_scan_tail() handles assigning functions to ecc ops:
If we are switching to software ecc/no ecc, it assigns default functions to the
ecc ops pointers unconditionally, but if we are switching to hardware ecc,
the default hardware ecc functions are assigned to ops pointers only if these
pointers are NULL (so that drivers could set their own functions). In the case
of omap_gpmc.c driver, when we switch to sw ecc, sw ecc functions are
assigned to ecc ops by nand_scan_tail(), and when we later switch to hw ecc,
the ecc ops pointers are not NULL, so nand_scan_tail() does not overwrite
them with hw ecc functions.
The result: sw ecc functions used to write hw ecc data.
Clear the ecc ops pointers in omap_gpmc.c when switching ecc types, so that
ops which were not assigned by the driver will get the correct default values
from nand_scan_tail().
Cc: Scott Wood <scottwood@freescale.com>
Cc: Pekon Gupta <pekon@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
When switching ecc mode, omap_select_ecc_scheme() assigns the appropriate values
into the current nand chip's ecc.layout struct. This is done under the
assumption that the struct exists only to store values, so it is OK to overwrite
it, but there is at least one situation where this assumption is incorrect:
When switching to 1 bit hamming code sw ecc, the job of assigning layout data
is outsourced to nand_scan_tail(), which simply assigns into ecc.layout a
pointer to an existing struct prefilled with the appropriate values. This struct
doubles as both data and layout definition, and therefore shouldn't be
overwritten, but on the next switch to hardware ecc, this is exactly what's
going to happen. The next time the user switches to software ecc, they're
going to get a messed up ecc layout.
Prevent this and possible similar bugs by explicitly using the
private-to-omap_gpmc.c omap_ecclayout struct when switching ecc mode.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Pekon Gupta <pekon@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Commit "mtd: nand: omap: enable BCH ECC scheme using ELM for generic
platform" (d016dc42ce) changed the way
software ECC is configured, both during boot, and during ecc switch, in a way
that is not backwards compatible with older systems:
Older version of omap_gpmc.c always assigned ecc.size = 0 when configuring
for software ecc, relying on nand_scan_tail() to select a default for ecc.size
(256), while the new version of omap_gpmc.c assigns ecc.size = pagesize,
which is likely to not be 256.
Since 1 bit hamming sw ecc is only meant to be used by legacy devices, revert
to the original behavior.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Pekon Gupta <pekon@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: wrap some long lines]
Signed-off-by: Scott Wood <scottwood@freescale.com>
As per OMAP3530 TRM referenced below [1]
For large-page NAND, ROM code expects following ecc-layout for HAM1 ecc-scheme
- OOB[1] (offset of 1 *byte* from start of OOB) for x8 NAND device
- OOB[2] (offset of 1 *word* from start of OOB) for x16 NAND device
Thus ecc-layout expected by ROM code for HAM1 ecc-scheme is:
*for x8 NAND Device*
+--------+---------+---------+---------+---------+---------+---------+
| xxxx | ECC[A0] | ECC[A1] | ECC[A2] | ECC[B0] | ECC[B1] | ECC[B2] | ...
+--------+---------+---------+---------+---------+---------+---------+
*for x16 NAND Device*
+--------+--------+---------+---------+---------+---------+---------+---------+
| xxxxx | xxxxx | ECC[A0] | ECC[A1] | ECC[A2] | ECC[B0] | ECC[B1] | ECC[B2] |
+--------+--------+---------+---------+---------+---------+---------+---------+
This patch fixes ecc-layout *only* for HAM1, as required by ROM-code
For other ecc-schemes like (BCH8) ecc-layout is same for x8 or x16 devices.
[1] OMAP3530: http://www.ti.com/product/omap3530
TRM: http://www.ti.com/litv/pdf/spruf98x
Chapter-25: Initialization Sub-topic: Memory Booting
Section: 25.4.7.4 NAND
Figure 25-19. ECC Locations in NAND Spare Areas
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Stefan Roese <sr@denx.de>
ROM did not invalidate L1 cache when download by usb
Need invalidate L1 cache before enable cache
Signed-off-by: Huang yongcai <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
According to NOTE in strtoul(3), the errno must be zeroed before strtoul()
is called. Zero the errno. The NOTE reads as such:
Since strtoul() can legitimately return 0 or ULONG_MAX (ULLONG_MAX for
strtoull()) on both success and failure, the calling program should set
errno to 0 before the call, and then determine if an error occurred
by checking whether errno has a nonzero value after the call.
This issue was detected on Fedora 19 with glibc 2.17 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
mx6sabresd boards have a 18-bit LVDS data width and the correct color format
is RGB666.
Suggested-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
HSYNC, VSYNC and DISP_CLK are very useful display signals for debugging.
Configure them as active pins.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to the mx6 quad reference manual, the DIV_SELECT field of register
CCM_ANALOG_PLL_ENETn has the following meaning:
"Controls the frequency of the ethernet reference clock.
- 00 - 25MHz
- 01 - 50MHz
- 10 - 100MHz
- 11 - 125MHz"
Current logic does not handle the 25MHz case correctly, so fix it.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds support for the AMPIRE 800x480 LCD panel that is available
for M53EVK.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Align with the context to use readl() to read the CCM_CCGR3
register with memory barrier instead of __raw_readl().
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
The CPU errata expressed in include/configs/mx6_common.h apply
to all i.MX6DQ and i.MX6DLS parts.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
According to the README:
"- CONFIG_SYS_SPD_BUS_NUM
If SPD EEPROM is on an I2C bus other than the first
one, specify here. Note that the value must resolve
to something your driver can deal with."
There is no SPD EEPROM on the imx boards, so ged rid of this option.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add SATA support on uDoo Board.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Move setup_sata function definition from platform file nitrogen6x.c
to arch/arm/imx-common/sata.c to avoid code duplication.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, move the
CONFIG_SYS_NO_FLASH to proper position, then we don't need to undef
these two commands.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
remove unneeded #undef for at91sam9x5ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
As the cs for spi is worked in gpio mode, so no need to configure
it as peripheral and then configure to gpio. Configure it to gpio
directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This allows the use of either or both declarations from
the files mx6q_pins.h and mx6dl_pins.h.
All board files should include <asm/arch/mx6-pins.h>
with one of the following defined in boards.cfg
MX6Q - for boards targeting i.MX6Q or i.MX6D
MX6DL - for boards targeting i.MX6DL
MX6S - for boards targeting i.MX6S
MX6QDL - for boards that support any of the above with
run-time detection
Pad declarations will be MX6_PAD_x for single-variant boards
and MX6Q_PAD_x and MX6DL_PAD_x for boards supporting both
processor classes.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The pmic_init() function has the I2C or SPI bus number that is connected to the
PMIC.
Instead of passing I2C_PMIC, explicitly pass the I2C bus number via I2C_x
definition.
The motivation for doing this is to avoid people just doing a copy and paste
of I2C_PMIC into their board file when another I2C bus is actually used to
interface to their PMIC.
This also makes more obvious which is the I2C bus connected to the PMIC, without
having to search in the source code for the meaning of the 'I2C_PMIC' number.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Commit fea25720 renamed arch/i386 to arch/x86.
But it missed to modify examples/standalone/Makefile.
Since then, examples/standalone/82559_eeprom has
never compiled and nobody has noticed that.
After some discussion on ML, we agreed to delete this example.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Convert like follows:
CPU mpc83xx -> CONFIG_MPC83xx
CPU mpc85xx -> CONFIG_MPC85xx
CPU mpc86xx -> CONFIG_MPC86xx
CPU mpc5xxx -> CONFIG_MPC5xxx
CPU mpc8xx -> CONFIG_8xx
CPU mpc8260 -> CONFIG_8260
CPU ppc4xx -> CONFIG_4xx
CPU x86 -> CONFIG_X86
ARCH x86 -> CONFIG_X86
ARCH powerpc -> CONFIG_PPC
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
fdt_fixup_memory_banks() will add and update /memory node in
device tree blob. In the case that /memory node doesn't exist,
after adding a new one, this function returns error.
The correct behavior should be continuing to update its properties.
Signed-off-by: Miao Yan <miao.yan@windriver.com>
The next version VxWorks adopts device tree (for PowerPC and ARM) as its hardware
description mechanism. For PowerPC, the boot interface conforms to
the ePAPR standard, which is:
void (*kernel_entry)(ulong fdt_addr,
ulong r4 /* 0 */,
ulong r5 /* 0 */,
ulong r6 /* EPAPR_MAGIC */, ulong r7 /* IMA size */,
ulong r8 /* 0 */, ulong r9 /* 0 */)
For ARM, the boot interface is:
void (*kernel_entry)(void *fdt_addr)
Signed-off-by: Miao Yan <miao.yan@windriver.com>
[trini: Fix build error when !CONFIG_OF_FDT is set, typo on PowerPC,
missing extern ft_fixup_num_cores]
Signed-off-by: Tom Rini <trini@ti.com>
do_bootm_vxworks now is available under the configuration option
CONFIG_BOOTM_VXWORKS, thus aligned with other operating systems
that supported by bootm command. The bootvx command still depneds
on CONFIG_CMD_ELF.
Signed-off-by: Miao Yan <miao.yan@windriver.com>
We have some scripts imported from Linux Kernel:
setlocalversion, checkstack.pl, checkpatch.pl, cleanpatch
They are located under tools/ directory in U-Boot now.
But they were originally located under scripts/ directory
in Linux Kernel.
This commit moves them to the original location.
It is true that binutils-version.sh and dtc-version.sh
do not originate in Linux Kernel, but they should
be moved by analogy to gcc-version.sh.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
