Commit graph

34341 commits

Author SHA1 Message Date
Masahiro Yamada
2661dfd004 ARM: UniPhier: enable output of system bus
For NAND boot on PH1-LD4, PH1-sLD8, and some other SoCs,
the output of the system bus is disabled by default.
It must be enabled by software to have access to the system bus.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-01-08 23:01:45 +09:00
Masahiro Yamada
5e165b258f ARM: UniPhier: fix SRAM size on support card
The max size of available memories on slot0 and slot1 is 32MB because
 - EA[25] signal is not output on the save-pin mode which is
   used PH1-LD4 or later SoCs.
 - EA[25] signal is not connected by the limitation (or bug?) of
   the PLD logic of DCC support card.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-01-08 23:01:21 +09:00
Axel Lin
78c80114b5 spi: ftssp010_spi: Simplify code flow in ftssp010_[wait|wait_tx|wait_rx]
No functional change, just simplify the code a bit.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-08 12:02:55 +05:30
Masahiro Yamada
40ad4c4b1f Kconfig: move EXPERT option under "General setup" menu
Make it a sub-menu of "General setup" like Linux Kernel.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
2015-01-07 14:48:47 -05:00
Axel Lin
1dc7d00f27 spi: cadence_qspi: Fix checking return value of fdt_first_subnode()
fdt_first_subnode() returns -FDT_ERR_NOTFOUND if no subnode found.
0 is supposed to be a valid offset returns from fdt_first_subnode().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-07 12:30:54 +05:30
Peng Fan
d87cbeccc5 mx6sxsabresd: support qspi flash bigger than 16MB
mx6sxsabresd revb board uses 32MB qspi flash, reva board uses 16MB qspi
flash. Currently, the default supported platform is revb board.

If want to configure for reva board, just define CONFIG_MX6SX_SABRESD_REVA
in mx6sxsabresd.h to support reva qspi flashes whose size is 16MB.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-07 12:25:05 +05:30
Peng Fan
a235878387 spi:fsl-quadspi support bank register read write
To support bigger than 16MB size qspi flashes, spi framework uses bank
switch to access higher bank or lower bank.

In this patch, QSPI_CMD_BRRD, QSPI_CMD_BRWR, QSPI_CMD_WREAR, QSPI_CMD_RDEAR
is initialized in LUT register with related pad and length configuration.
qspi_op_pp is originally for page programming, this patch reuses this function
for bank register switch and renamed it with qspi_op_write.

Since bank or EAR register is only 1 byte length, however original qspi_op_pp
or now renamed qspi_op_write only support 4 bytes lenght as the access unit,
this will trigger data abort exception when access EAR or bank register.
This is because upper framework passes a 1 bytes pointer to qspi_op_write,
however qspi_op_write treat it as an int pointer. This patch fixes this for
accessing EAR or bank register.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-07 12:25:05 +05:30
Marek Vasut
653cda8f66 dt: socfpga: Replace num-chipselect with num-cs
This optional DT property is called 'num-cs', so repair the misnomers.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-07 12:13:30 +05:30
Tom Rini
7375f4007f Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2015-01-06 10:48:32 -05:00
Tom Rini
2ed3f91143 Merge branch 'master' of git://git.denx.de/u-boot-mmc 2015-01-06 10:44:47 -05:00
Marek Vasut
7411486253 dt: socfpga: Rename snps, dw-spi-mmio to snps, dw-apb-ssi
Linux now also contains SPI driver, yet the name is 'snps,dw-apb-ssi'.
Fix the naming before we have to support both names.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-06 16:02:58 +05:30
Hans de Goede
5ba471944a sunxi: axp221: Fix using the wrong register address for ALDO2
This fixes us never programming ALDO2, and programming the ALDO2 voltage
into ALDo1.

Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-06 11:25:47 +01:00
Axel Lin
501943696e spi: designware_spi: Fix detecting FIFO depth
Current code tries to find the highest valid fifo depth by checking the value
it wrote to DW_SPI_TXFLTR. There are a few problems in current code:
1) There is an off-by-one in dws->fifo_len setting because it assumes the latest
   register write fails so the latest valid value should be fifo - 1.
2) We know the depth could be from 2 to 256 from HW spec, so it is not necessary
   to test fifo == 257. In the case fifo is 257, it means the latest valid
   setting is fifo = 256. So after the for loop iteration, we should check
   fifo == 2 case instead of fifo == 257 if detecting the FIFO depth fails.
This patch fixes above issues.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-06 15:52:27 +05:30
Guillaume GARDET
2c84c9a40a spl: mmc: Fix raw boot mode (related to commit 4c5bbc2328)
As reported by Robert Nelson, commit 4c5bbc2328
may break MMC RAW boot mode.
This patch fixes the check path to fix MMC Raw boot mode.

Tested raw boot mode and FS boot mode on a pandaboard (rev. A3).

Reported-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>

Cc: Tom Rini <trini@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
2015-01-06 10:10:30 +02:00
Gerald Kerma
ac0b729844 MVEBUMMC : REMOVE unnecessary delay from init
Remove unnessecary delay from mvebu_mmc_initialize

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:10:28 +02:00
Gerald Kerma
02b2739e8f MVEBUMMC : CLEAN code
Clean mvebu_mmc_send_cmd

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:10:23 +02:00
Gerald Kerma
86eeecafc2 MVEBUMMC : REMOVE unnecessary delays
Remove delays in mvebu_mmc_set_bus and mvebu_mmc_set_clk

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:10:16 +02:00
Gerald Kerma
fc0f25f919 MVEBUMMC : FIX debug strings
Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:10:12 +02:00
Gerald Kerma
28d27b79e3 MVEBUMMC : Speed up access time
Get about 40x faster access on SHEEVAPLUG MMC
 Fix some SD type compatibility

 Changes in v3:
 - fix the HW_STATE (from linux mvsdio)
 - review delays and timeouts

 Changes in v2:
 - increase number of loops
 - remove initial delay

 Changes in v1:
 - review all loops, delays and timeouts

Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:10:04 +02:00
Gerald Kerma
2591fbdba3 MVEBUMMC : Change copyright date
Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-01-06 10:09:45 +02:00
Tom Rini
fc89b2e479 spl_sata.c: Add <scsi.h>
We need <scsi.h> for scsi_scan().

Signed-off-by: Tom Rini <trini@ti.com>
2015-01-05 21:14:04 -05:00
Tom Rini
fc078895d8 Merge branch 'misc' of git://git.denx.de/u-boot-x86 2015-01-05 20:00:25 -05:00
Sjoerd Simons
9332274989 cros-ec-keyboard: Synchronize DT binding from linux
The ChromeOS EC keyboard is used by various different chromebooks. Peach
pi being the third board in the u-boot tree to use it (snow and peach
pit the other two). Rather then embedding the same big DT node in the
peach-pi DT again, copy the dtsi snippit & bindings documentation from
linux and include it in all 3 boards.

This slightly changes the dt bindings in u-boot:
  * google,key-rows becomes keypad,num-rows
  * google,key-colums becomes keypad,num-colums
  * google,repeat-delay-ms and google,repeat-rate-ms are no longer used
    and replaced by hardcoded values (similar to tegra kbc)

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2015-01-05 17:45:16 -07:00
Masahiro Yamada
ee5ee87642 i2c_eeprom: include <linux/err.h> to fix build error
drivers/misc/i2c_eeprom.c fails to build unless CONFIG_FIT_SIGNATURE
is defined.

  CC      drivers/misc/i2c_eeprom.o
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:15:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:15:10: note: each undeclared identifier
is reported only once for each function it appears in
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_write':
drivers/misc/i2c_eeprom.c:21:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:22:1: warning: control reaches end of
non-void function [-Wreturn-type]
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:16:1: warning: control reaches end of
non-void function [-Wreturn-type]
make[2]: *** [drivers/misc/i2c_eeprom.o] Error 1
make[1]: *** [drivers/misc] Error 2
make: *** [drivers] Error 2

By the way, Sandbox (enabling CONFIG_FIT_SIGNATURE) is luckily
working depending on it.
Sandbox includes include/asm-generic/errno.h
            from include/errno.h
            from include/u-boot/rsa-checksum.h
            from include/image.h
            from include/common.h
            from drivers/misc/i2c_eeprom.c

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-05 17:45:15 -07:00
Masahiro Yamada
33fcd1bbd5 dm: README: recommend u-boot.dtb to try driver-model on sandbox
To enjoy driver-model on sandbox, using device tree is recommended.
While we are here, change sandbox_config to sandbox_defconfig too.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-05 17:45:15 -07:00
Sonic Zhang
22cfddc2a0 memmove_wd: copy chunk down from big address if parameter to is larger than from
When watchdog is enabled, memmove_wd() always copy chunk up from small address.
This damanges overlapped memory data if destination address is smaller than
source address.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-05 16:40:19 -05:00
Guido Martínez
eb54d2c70c mtd: nand: omap_gpmc: fix error handling
"err" was an unsigned variable, causing negative error codes to turn
into positive values, which are interpreted as an amount of succesfully
corrected bitflips (and thus not an error).

In particular, this resulted in that if the elm reports uncorrectable
errors (-EBADMSG), the MTD layer (and UBI) falsely succeeded.

Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-01-05 16:40:18 -05:00
David Büchi
001475a0f5 powerpc/cm5200: migrate to generic board
Signed-off-by: David Buechi <david.buechi@bbv.ch>
2015-01-05 16:40:18 -05:00
Jeremiah Mahler
b445bbb49f doc: fix grammatical errors in README
Fix various spelling and grammatical errors in the README.

Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-05 15:13:47 -05:00
Karicheri, Muralidharan
58927a964e keystone: set default pci mode to root complex
pci ports are used as root complex in Linux. So set this as default
in u-boot for keystone devices

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
2015-01-05 15:13:47 -05:00
Felipe Balbi
301ecbb130 beagle_x15: enable NFS command
NFS is useful for loading zImage and dts through
NFS export. It saves us from running two services
for loading files over the network (tftp and nfs).

Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-05 15:13:47 -05:00
Dmitry Lifshitz
96b5bf11ca omap5: cm-t54: add sata support
Add configs required for SATA support on CM-T54 board.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
2015-01-05 15:13:47 -05:00
Dmitry Lifshitz
87791adc22 arm: omap: reset sata on boot
On OMAP platforms (like OMAP5) Linux kernel fails to detect a SATA
device if it is used by U-Boot.

It happens because U-Boot does not reset SATA controller before boot.

Reset the controller on OS boot so that Linux will have a clean state
to work with.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
2015-01-05 15:13:47 -05:00
Dmitry Lifshitz
8decf5d4a5 OMAP5+: sata/scsi: implement scsi_bus_reset()
Implement missing scsi_bus_reset() for SCSI subsystem commands
on OMAP platforms.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
2015-01-05 15:13:46 -05:00
Dmitry Lifshitz
1a33b7356a ahci-plat: provide a weak scsi_bus_reset() hook
This allow the platform to handle a custom reset sequence.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
2015-01-05 15:13:46 -05:00
Dmitry Lifshitz
6b68888a33 ahci: introduce ahci_reset()
Extract controller reset code from ahci_host_init() into separate
ahci_reset().

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
2015-01-05 15:13:46 -05:00
Peter Howard
2a10f8b948 da850evm: Use generic board and libfdt, fix size for SPI flash
Add defines to use CONFIG_SYS_GENERIC_BOARD and CONFIG_OF_LIBFDT.
Semi-separate to this: the size of the image for the da850evm has
increased to the point that the size in da850evm.h and the offset for
the environment in SPI flash no longer work.  They are modified to
account for the larger image size.

Signed-off-by: Peter Howard <phoward@gme.net.au>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-05 15:13:46 -05:00
Przemyslaw Marczak
64f65e1e36 fs: fat: read: fix fat16 ls/read issue
The present fat implementation ignores FAT16 long name
directory entries which aren't placed in a single sector.

This was becouse of the buffer was always filled by the
two sectors, and the loop was made also for two sectors.

If some file long name entries are stored in two sectors,
the we have two cases:

Case 1:
Both of sectors are in the buffer - all required data
for long file name is in the buffer.
- Read OK!

Case 2:
The current directory entry is placed at the end of the
second buffered sector. And the next entries are placed
in a sector which is not buffered yet. Then two next
sectors are buffered and the mentioned entry is ignored.
- Read fail!

This commit fixes this issue by:
- read two sectors after loop on each single is done
- keep the last used sector as a first in the buffer
  before the read of two next

The commit doesn't affects the fat32 imlementation,
which works good as previous.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Mikhail Zolotaryov <lebon@lebon.org.ua>
Cc: Tom Rini <trini@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Tested-by: Simon Glass <sjg@chomium.org>
2015-01-05 15:13:46 -05:00
Nishanth Menon
5b782e3f4c TI: armv7: enable UUID and PART
Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes

And remove it from headers that end up redefining it.

Signed-off-by: Nishanth Menon <nm@ti.com>
2015-01-05 15:13:45 -05:00
Nishanth Menon
25098144ac Revert "ARM: omap4: Update sdram setting for panda rev A6"
This reverts commit 47a4bea6af.

Signed-off-by: Nishanth Menon <nm@ti.com>
2015-01-05 15:13:45 -05:00
Nishanth Menon
38e5a5abda ARM: OMAP4: Panda: rework DMM logic
Part of DMM logic is reuse from commit
47a4bea6af ("ARM: omap4: Update sdram
setting for panda rev A6") Which broke SDP4430 with ES2.3 (uses old
DDR).

So, to maintain support for newer DDR used in Panda ES rev B3, we
should, in addition to the commit
675cc77a3a ("ARM:OMAP4+: panda-es: Support
Rev B3 Elpida DDR2 RAM"), DDR timings, also do DMM configuration
specific to Panda.

Signed-off-by: Nishanth Menon <nm@ti.com>
2015-01-05 15:13:45 -05:00
Tom Rini
b31079282e omap-common/hwinit-common.c: timer_init() doesn't need to touch gd
The gd will be cleared at first so we don't need to set arch.tbl to 0.
In addition, the checks later against lastinc also work fine with an
initial value of 0 here.  This also brings us in line with sunxi code
for example.

Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-01-05 15:13:45 -05:00
Tom Rini
b352dde1ea am33xx: Drop timer_init call from s_init
In both SPL and non-SPL cases we will make a call to timer_init() early
on and do not need to call it again within s_init().

Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-01-05 15:13:45 -05:00
Tom Rini
57b5e43e95 socfpga: Drop redundant save_boot_params
The save_boot_params function here is the same as the default weak one
from arch/arm/cpu/armv7/start.S, drop.

Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-01-05 15:13:44 -05:00
Hua Yanghao
90bac29a76 cmd_fdt: fix working_fdt is set to wrong value
Instead of setting working_fdt to map_sysmem(addr) (e.g. blob), it should be set
to addr directly as inside set_working_fdt_addr it uses map_sysmem(addr) again.
To test: ./u-boot -d dts/dt.bin , then issue: fdt addr 0x100, fdt print will
then cause an segmentation fault. After this fix fdt print is functional.
2015-01-05 15:13:28 -05:00
Ian Campbell
97a8196451 ARM: bootm: do not add PSCI to fdt when booting in secure mode.
Commit 8bc347e2ec "ARM: bootm: Allow booting in secure mode on hyp capable
systems" added the capability to select nonsec vs sec mode boot via an
environment var.

There is a subtle gotcha with this functionality, which is that the PSCI nodes
are still created in the fdt (via armv7_update_dt->fdt_psci) even when booting
in secure mode. Which means that if the kernel is PSCI aware then it will fail
to boot because it will try and do PSCI from secure world, which won't work.

This likely didn't get noticed before because the original purpose was to
support booting the legacy linux-sunxi kernels which don't understand PSCI.

To fix expose boot_nonsec (renaming with armv7_ prefix) outside of bootm.c and
use from the virt-dt code.

As well as avoiding the creation of the PSCI nodes we should also avoid
reserving the secure RAM, so do so.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2015-01-05 15:02:03 -05:00
Anthoine Bourgeois
c313c031cf devkit8000: convert to use generic board code
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
2015-01-05 13:48:21 -05:00
Alexey Brodkin
946f6f242c cmd_bdinfo: check for CONFIG_ARC instead of CONFIG_ARC700
For all flavours of ARC we execute the same code in "bdinfo" so we may
safely check for CONFIG_ARC. This is especially important since we're
about to add more types of ARC so existing check won't work in all
cases.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
2015-01-05 13:48:21 -05:00
Nikita Kiryanov
623185dbea arm: omap3: cm-t35: convert to generic board
Convert cm-t35 to generic board.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-05 13:48:21 -05:00
Masahiro Yamada
d622ac3927 powerpc: mpc824x: remove MPC824X cpu support
All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>
2015-01-05 12:08:55 -05:00