- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result. The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED. This seems like the most likely use, historically, of
the variable, but it was not used. Add logic to check for this now.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Except for one counter example, CONFIG_SYS_LBC_LBCR always has a value
of either 0x00040000 or 0x00000000.
CONFIG_SYS_LBC_MRTPR always has the value 0x20000000.
CONFIG_SYS_LBC_LSDMR_{1,2,4,5} are not set for any mpc83xx board.
CONFIG_SYS_LBC_LSRT is set by one board (to 0x32000000).
To simplify the configuration files, hardcode the setting of these
values for mpc83xx.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_SYS_DDR_SDRAM_BASE is set to the same value as
CONFIG_SYS_SDRAM_BASE on all existing boards. Just use
CONFIG_SYS_SDRAM_BASE instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_SYS_DDR_BASE is specific to mpc83xx an is always set to the same
value as CONFIG_SYS_SDRAM_BASE. Just use CONFIG_SYS_SDRAM_BASE instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Migrate the BR/OR settings to Kconfig. These must be known at compile
time, so cannot be configured via DT.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Re-format all BR,OR #define lines into single lines. This makes them
harder to read, but accessible to semi-automatic replacement.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
All BR/OR option lines should have the same layout to make them easier
to migrate to Kconfig. This includes using the same option macros
everywhere.
The normalize the lines,
* replace function macros with their results, and
* replace hardcoded hex values with standard macros
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The LBLAW_* values determine the window configuration of the memory
controller. Hence, they must be known at compile time, and cannot be
implemented in the DT mechanism.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The BATs (block address translation registers) determine the initial
memory window mappings. Hence, they must be known at compile time and
cannot be implemented in the DT mechanism.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The HRCW (hardware reset configuration word) is a constant that must be
hard-coded into the boot loader image. So, it must be available at
compile time, and cannot be migrated to the DT mechanism, but has to be
kept in Kconfig.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the
system clock. To migrate the architecture, we can replace
CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ.
To do this
* replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ
* set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all
MPC83xx config files
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The MPC83xx include files contain some settings of the PCI subsystem.
Migrate these to Kconfig until a proper DM PCI driver exists.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
vme8349.h contains two separate boards: The vme8349 itself, and the
caddy2 board. The caddy2 board is chosen by setting certain config
variables. Create a proper config file for the caddy2 board to make
Kconfig migration easier.
Furthermore, simplify the vme8349 and caddy2 configs by keeping only the
options necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
