The SoM has been redesigned to work around bug in the SoC and is now
capable of booting from the eMMC. Add support for booting from eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The SDHCI1 is the primary boot controller on rev. 2.1 SoM, which
is the version available on the market. Swap the controller order
to match this and future versions of the SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Init the controllers, otherwise the board cannot boot from SD/MMC.
This boot option is new on rev. 2.1 SoM .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Enable DFU and USB mass storage support for the DENX MA5D4 SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The CAN controllers need slight delay between toggling of their reset
line. Move this action into board_init(), otherwise timer will not be
initialized and the board might hang.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
According to the datasheet, sequential mapping is used for DDR
SDRAM, while interleaved mapping is used for regular SDRAM.
Incorrect configuration of this bit does indeed cause sporadic
memory instability.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
ARC HS Development Kit board is a new low-cost
development platform sporting ARC HS38 in real silicon
with nice set of features such as:
* Quad-core ARC HS38 with 512 kB L2 cache and running @1GHz
* 4Gb of DDR (we use only lowest 1Gb out of it now)
* Lots of DesigWare peripherals
* Different connectivity modules:
- Synopsys HAPS HT3
- Arduino-compatible connector
- MikroBUS
This initial commit supports the following peripherals:
* UART (DW 8250)
* Ethernet (DW GMAC)
* SD/MMC (DW Mobile Storage)
* USB 1.1 & 2.0
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We used to use the same memory layout and size for a couple of
boards and thus we just hardcoding IOC aperture start and size.
Now when we're getting more boards with more memory on board we
need to have an ability to set IOC so it matches real DDR layout
and size.
Even though it is not really a must but for simplicity we assume
IOC covers all the DDR we have, that gives us a chance to not
bother where DMA buffers are allocated - any part of DDR is OK.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With deprecation of I2C EEPROM we we left without a permamnent
storage for U-Boot environment, but luckily we may simply use SD-card
with FAT partition for that.
Having environment on SD-card is much more convenient as it
allows us to preserve all the settings when moving from one board to
another. Moreover instead of 256 bytes of EEPROM we're now virtually
unlimited in stuff being placed in environment like complicated scripts
etc which are usually required in case of full-scale distros.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With eb5ba3aefd "i2c: Drop use of CONFIG_I2C_HARD" in place we
cannot use I2C EEPROM any longer so we're dropping all references to
both EEPROM and I2C which was only used for EEPROM.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
ARCompact cores are not supposed to be used in SMP designs
(this doesn't stop people from creation of heterogeneous chips,
for an example keep reading) so there's no point in
checking ARCNUM and halting somebody if we build for ARC700.
Moreover on AXS101 board we have ARC770 in the ASIC together with
other ARC cores and ARC770 happens to be the last node in JTAG chain
with ARCNUM = 4. And existing check halts the one and only core we
want keep running.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
taurus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
since commit 842778a091 dfu-util shows serial="UNDEFINED".
to see here again a serial number, we have to call
g_dnl_set_serialnumber().
Signed-off-by: Heiko Schocher <hs@denx.de>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
fix warnings:
drivers/usb/gadget/at91_udc.c:1344:12: warning: 'at91rm9200_udc_init' defined but not used [-Wunused-function]
drivers/usb/gadget/at91_udc.c:1379:13: warning: 'at91rm9200_udc_pullup' defined but not used [-Wunused-function]
drivers/usb/gadget/at91_udc.c:1476:12: warning: 'at91sam9263_udc_init' defined but not used [-Wunused-function]
Signed-off-by: Heiko Schocher <hs@denx.de>
The CONFIG_DEFAULT_FDT_FILE expects just the file not a full path
as that might vary depending on the variant of Linux distro you
might be using.
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
Some Kconfig options are defined in a line with leading spaces/tabs.
Update build-whitelist/check-config scripts to handle such cases.
Generate a new config_whitelist.txt with new scripts.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The origin SPL_USE_ARCH_MEMSET/MEMCPY use same prompt message
as USE_ARCH_MEMSET/MEMCPY, which makes it's hard to distinguish
them in menuconfig interface. This patch gives them different
prompt messages for spl and none-spl config.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
After the commit SHA1: 842778a091 - the serial number descriptor is only
visible when we have non zero length of g_dnl_serial.
However, on some platforms (e.g. Siemens) the serial number is set at
g_dnl_bind_fixup(), so with the current code we will always omit the
serial (since it is not set).
This commit moves the g_dnl_bind_fixup() call before the g_dnl_serial
length test.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit ddb3ac3c71.
With MMC converted to driver model, SCSI driver is broken due to
zero address access at (ops->read) in block_dread() function.
The fix (SCSI driver converted to DM) is ready in u-boot-dm branch,
but it is too late for this relese to get that in.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These are only used in drivers/mis/i2c_eeprom.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add initial device tree support for LD20 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add initial device tree support for LD11 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix warnings reported by sparse:
- ... was not declared. Should it be static?"
- cast to restricted __be32
While fixing those, the type conflict of cci500_init() was found.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
According to rk3036 TRM, pll_con1[12] should be set to '1' for the pll
integer mode, while the '0' means the frac mode.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The maximum spl_size for rk3399 is the internal memory size minus
the size used in bootrom (which usually can get from SPL_TEXT_BASE).
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The SPL_MAX_SIZE is the internal memory size minux the space
used by bootrom.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This function is unused, remove. Reported by clang-3.8.
Fixes: a1c29d4b43 ("rockchip: mkimage: set init_boot_size to avoid ...")
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Adding myself to MAINTAINERS and git-mailrc for the rockchip
sub-architecture.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
fix menutext for the options SPL_DM_SERIAL and TPL_DM_SERIAL.
Both have the same text as DM_SERIAL, which is
confusing.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
for debugging it is handy to know the fdt_blob
address. So print it in bdinfo.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Otherwise the loaded image would miss the efi_runtime sections, and fall
over hard when grub (for example) tried to call runtime services located
in this section.
Signed-off-by: Rob Clark <robdclark@gmail.com>
commit dfe64e2c89
Author: Sergey Lapin <slapin@ossfans.org>
Date: Mon Jan 14 03:46:50 2013 +0000
mtd: resync with Linux-3.7.1
modified onenand_block_markbad to call mtd_block_markbad,
but as _block_markbad function pointer used by mtd_block_markbad
to do actual job is by default pointing back to
onenand_block_markbad there is no way this function ever
finishes its job.
Fix it by changing function body according current (4.12-rc6)
linux implementation.
Tested on IGEPv2 board with Muxed OneNAND(DDP) 512MB containing
several unerasable blocks this function marked bad.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Current implementation is unable to access second half of
DDP OneNAND flash (reads first half mirrored). Use block
and bufferram address calculations from onenand_base to
fix this.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Define a default number of 1 for mmc max device if board config didn't
specify one.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The variables gpll_init_cfg and apll_init_cfg are unused in this file,
remove them.
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
