It seems that waiting only 10 ms after releasing LAN switch from reset
is not enough for the strapping pins to latch the requested values.
P6_MODE[0] is latched to 0 instead of 1.
Increasing the delay to 50 ms fixes this issue.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When rescue mode was activated reset also bootdelay env variable to its
default value. This will ensure that reset button works and starts rescue
mode also in the case when user changed bootdelay env variable to -1 (which
has meaning to not start autoboot).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Store serial number from atsha cryptochip into the serial# env variable.
U-Boot automatically puts content of this variable into the root device
tree property serial-number when booting Linux kernel. Refactor turris
atsha code and from turris_atsha_otp_get_serial_number() function returns
directly string suitable for printing or storing into device tree. Because
during different boot stages is env storage read-only, it is not possible
to always store serial number into env storage. So introduce a new function
turris_atsha_otp_init_serial_number() which is called at later stage and
which ensures that serial number is correctly stored into env.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There are already more MCU firmware versions for Turris Omnia in
production, so display git commit (version) of the MCU firmware during
U-Boot startup. It will help to identify what version of MCU firmware is
Turris Omnia using.
MCU firmware for Turris Omnia is open source and available at website:
https://gitlab.nic.cz/turris/hw/omnia_hw_ctrl
It can be updated from running system via i2c bus with this tool:
https://gitlab.nic.cz/turris/omnia-mcutool
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
SPI0 CS0 Flash is mapped to address range 0xD4000000 - 0xD7FFFFFF by BootROM.
Proper U-Boot removes this direct mapping. So it is available only in SPL.
This applies for all 32-bit Armada BootROMs. SPL mvebu code is used only on
32-bit Armada SoCs. So move env_sf_get_env_addr() function from Turris
Omnia board to common SPL mvebu code and add proper checks for SPI0 CS0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Linux kernel DTS files renamed spi-nor@0 node to flash@0 which effectively
broke U-Boot to boot new Linux kernel versions correctly.
So remove hardcoded spi-nor device tree path from Turris Omnia board code
and replace it by searching for mtd node by compatible string.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Sometimes fixup_mtd_partitions() prints during booting kernel error
"Failed fixing SPI NOR partitions!" because it does not have enough space
for creating all paritions nodes. So increase fdt size.
Fixes: 92f36c8e74 ("arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
All partitions are created by fixup_mtd_partitions() function, so they do
not have to exist just for their removal need.
Fixes: 92f36c8e74 ("arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
New Turris Omnia HW board revision requires that software controls
peripheral reset signals, namely PERST# signals on mPCIe slots, ethernet
phy reset and lan switch reset. Those pins are connected to MCU controlled
by MCU i2c API as GPIOs. On new HW board revision those pins stay in reset
after board reset and software has to release these peripherals from reset
manually. MCU announce this requirement by FEAT_PERIPH_MCU bit in
CMD_GET_FEATURES command.
On older HW board revisions when FEAT_PERIPH_MCU is not announced, all
those reset signals are automatically released after board finish reset.
Detect FEAT_PERIPH_MCU bit in board_fix_fdt() and ft_board_setup()
functions and insert into device tree blob pcie "reset-gpios" and eth phy
"phy-reset-gpios" properties with corresponding MCU gpio definitions.
PCIe and eth PHY drivers then automatically release resets during device
initialization. Both U-Boot and Linux kernel drivers support those device
tree reset properties.
Initialization of lan switch on new HW board revision is more complicated.
Switch strapping pins are shared with switch RGMII pins. And strapping pins
must be in specific configuration after releasing switch reset. Due to pin
sharing, it is first required to switch A385 side of switch pins into GPIO
mode, set strapping configuration, release switch from reset and after that
switch A385 pins back to RGMII mode.
Because this complicated setup is not supported by switch DSA drivers and
cannot be expressed easily in device tree, implement it manually in SPL
function spl_board_init(). So in proper U-Boot and OS/kernel would be lan
switch initialized and be in same configuration like it was on old HW board
revisions (where reset sequence did those steps at hardware level).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
Different Turris Omnia HW board revisions contains different MCU.
Show type in show_board_info() to easily identify which MCU is populated.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
This driver registers GPIO controller and allows U-Boot to control GPIO
pins on MCU which is connected to Turris Omnia via i2c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix MAINTAINERS files for Turris devices, add missing files and add Pali
as maintainer.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
PCIe Mini CEM 2.1 spec added support for USB3.0 mode on MiniPCIe cards.
USB3.0 and PCIe share same pins and only one function can be active at the
same time. PCIe Mini CEM 2.1 spec says that determining function is
platform specific and spec does not define any dedicated pin which could
say if card is USB3.0-based or PCIe-based.
Implement this platform specific decision (USB3.0 vs PCIe) for WWAN
MiniPCIe slot on Turris Omnia via U-Boot env variable "omnia_wwan_slot",
similarly like is implemented forced mode for MiniPCIe/mSATA slot via
"omnia_msata_slot" env variable. Value "usb3" for "omnia_wwan_slot" would
mean to set USB3.0 mode and value "pcie" original PCIe mode.
A385 SoC on Turris Omnia has configurable fifth SerDes line (exported to
MiniPCIe WWAN slot with SIM card) either to USB3.0 or PCIe functionality,
so implementation of this new PCIe Mini CEM 2.1 feature is simple, by just
configuring SerDes to USB 3.0 mode.
Other twos MiniPCIe slots on Turris Omnia do not have this new
functionality as their SerDes lines cannot be switched to USB3.0
functionality.
Note that A385 SoC does not have too many USB3.0 blocks, so activating
USB3.0 in MiniPCIe cause that one external USB3.0 USB-A port would loose
USB3.0 functionality and would be downgraded just to USB2.0.
By default this MiniPCIe WWAN slot is in PCIe mode, like before.
To set this MiniPCIe WWAN slot to USB3.0 mode, call U-Boot commands:
=> setenv omnia_wwan_slot usb3
=> saveenv
=> reset
Signed-off-by: Pali Rohár <pali@kernel.org>
Show error message when DT file does not contain sata or pcie node which
should be explicitly disabled. This can happen when U-Boot code for finding
those nodes is incomplete or when those DT nodes are in different
unexpected location. In any case it is needed to know if DT not was not
explicitly disabled as it could mean that combo slots where setup
incorrectly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Move code for disabling sata and pcie DT nodes to own functions, so this
code can be called from other places in follow up patches.
Signed-off-by: Pali Rohár <pali@kernel.org>
Some PCIe-based MiniPCIe cards are broken and they do not ground PIN 43
which is required by PCIe mini CEM specs. Such broken cards are incorrectly
detected as mSATA cards because SATA specs requires that PIN 43 on mSATA
cards has to be disconnected.
PIN 43 on Turris Omnia is used only for MiniPCIe/mSATA card detection by
software in U-Boot SPL. Allow to override that U-Boot SPL detection by a
new "omnia_msata_slot" env variable (to value "pcie" or "sata") so broken
MiniPCIe cards can be used in combo mSATA/MiniPCIe slot too.
As configuration of PCIe vs SATA functionality is done in U-Boot SPL,
it is required to change env variable in permanent storage and reset the
board to take effect.
To force PCIe mode for broken MiniPCIe cards, call U-Boot commands:
=> setenv omnia_msata_slot pcie
=> saveenv
=> reset
Signed-off-by: Pali Rohár <pali@kernel.org>
By default use primary serdes map with PCIe function in combined
miniPCIe/mSATA slot. When SATA is detected change serdes map variable at
runtime.
Signed-off-by: Pali Rohár <pali@kernel.org>
BootROM maps SPI Flash to fixed address 0xD4000000 and this mapping is
active also when BootROM is executing binary kwbimage headers, which
includes also U-Boot SPL.
Therefore no initialization code is required to access SPI Flags from
U-Boot SPL. In proper U-Boot it is remapped to other location.
So in mvebu implementation of env_sf_get_env_addr() function returns
0xD4000000 when running in SPL and NULL when in proper U-Boot.
This change would allow to use U-Boot ENV in U-Boot SPL. Normally it is not
possible to read ENV because it is too big and U-Boot SPL does not have
such big malloc() pool to real all ENV variables.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Turris Omnia uses first MAC address from OTP for second ethernet interface.
Second MAC address for third interface and third MAC address for first
interface.
Other Turris routers do not have this rotate by one mapping. So add
function parameter for specifying id of the first ethernet interface.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
OTP code is not Atsha generic but also it is not Omnia specific. It is
common for all Turris routers which use Atsha cryptochip for storing OTP.
So move this common Turris specific Atsha OTP code from Turris Omnia into
separate file. It will be used also by other Turris routers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
On of the MiniPCIe ports on Turris Omnia is also a mSATA port. Whether
it works in SATA or PCIe mode is determined by a strapping pin, which
value is read from the MCU.
We already determine which type of card is connected when configuring
SerDeses.
But until now we left both SATA and PCIe port 0 nodes in device tree
enabled, and so the SATA driver is probed in U-Boot / Linux even if we
know there is no mSATA card, and similarly PCIe driver tries to link on
port 0 even if we know there is mSATA card, not a PCIe card.
Fixup device tree blob to disable SATA node if mSATA card is not
present, and to disable PCIe port 0 node if mSATA card is present.
Do this for U-Boot's DT blob before relocation and also for kernel DT
blob before booting.
This ensures that software does not try to use SATA or PCIe HW when
corresponding PHY is not configured.
Signed-off-by: Pali Rohár <pali@kernel.org>
[ refactored and fixed some issues ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit aeb0ca64db ("arm: mvebu: turris_omnia: disable MCU watchdog in
SPL when booting over UART") disabled MCU watchdog when booting over
UART to ensure that watchdog does not reboot the board before UART
transfer finishes.
But if UART transfer fails for some reason, or if U-Boot binary crashes,
then board hangs forever as there is no watchdog running which could
reset it.
To fix this issue, enable A385 watchdog with very high timeout before
disabling MCU watchdog to ensure that even slow transfer can finish
successfully before watchdog timer expires and also to ensure that if
board hangs for some reason, watchdog will reset it.
Omnia's MCU watchdog has fixed 120 seconds timer and it cannot be
changed (without updating MCU firmware). A385 watchdog by default uses
25 MHz input clock and so the largest timeout value (2^32-1) can be
just 171 seconds. But A385 watchdog can be switched to use NBCLK (L2) as
input clock (on Turris Omnia it is 800 MHz clock) and in this case final
watchdog clock frequency is calculated as:
freq = NBCLK / 2 / (2 ^ R)
So A385 watchdog on Turris Omnia can be configured to at most 1374
seconds (about 22 minutes). We set it to 10 minutes, which should be
enough even for bigger U-Boot binaries or slower UART transfers.
Both U-Boot and Linux kernel, when initializing A385 watchdog, switch
watchdog timer to 25 MHz input clock, so usage of NBCLK input clock in
U-Boot SPL does not cause any issues.
Fixes: aeb0ca64db ("arm: mvebu: turris_omnia: disable MCU watchdog in SPL when booting over UART")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Linux enumerates MTD partitions in DTB order, while the fdt_add_subnode()
function puts a new subnode at the beginning.
To fix this, put MTD partitions into DTB in reverse order.
Fixes: 92f36c8e74 ("arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
We are printing board information in checkboard() function, which is
called from the default weak implementation of show_board_info().
Rename checkboard() to show_board_info(). This throws away the weak
implementation of show_board_info().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently we always overwrite ethaddrs with those from EEPROM.
In order to allow user to use a cloned MAC address in U-Boot, change the
code so that it sets ethaddr variables only if they aren't set or are
invalid.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
After getting MTD device via get_mtd_device_nm(), we need to put it with
put_mtd_device(), otherwise we get
Removing MTD device #0 (mx25l6405d) with use count 1
before booting kernel.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Disable MCU watchdog in board_late_init() instead of board_init(), so
that it is disabled after U-Boot enables SOC watchdog instead of before.
This way there is no window when the board is vulnerable.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When booting over UART, sending U-Boot proper may take too much time and
MCU watchdog will reset the board before U-Boot proper is loaded.
Better disable MCU watchdog in SPL when booting over UART.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
We do not need to guard code in board_init() and board_late_init()
functions with the CONFIG_SPL_BUILD macro, since these functions are not
called in SPL.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fixup SPI NOR partition nodes in Linux' device tree prior booting Linux.
Linux' devicetree does not contain "u-boot-env" partition and we do not
want to add it there because the address is different between stock
U-Boot and current upstream U-Boot.
Instead we add code that recreates partition nodes from scratch
according to how U-Boot sees them (which is defined in U-Boot's device
tree).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
One of the points of putting the rescue boot command into default
environment is that user can invoke it without physical access to the
board (without having to press the factory reset button), by running
run bootcmd_rescue
in U-Boot's console.
Therefore we have to ensure that bootcmd_rescue is always set to default
value, regardless of whether the factory reset button was pressed.
Otherwise the variable will be empty for example after upgrade from
previous U-Boot.
Fixes: ec3784d626 ("arm: mvebu: turris_mox: add support for board rescue mode")
Fixes: 176c3e7760 ("arm: mvebu: turris_omnia: support invoking rescue boot from console")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.
Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Update rescue mode boot command on Turris Omnia. We are compressing the
image with lzma now.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
commit 6285efb8a118940877522c4c07bd7c64569b4f5f upstream.
the twin-die combined memory device should be treatened as X8
device and not as X16 one
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
[ - the default value for twin_die_combined is set to NOT_COMBINED for
all boards, as this was default behaviour prior this change ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Rescue mode bootcmd currently only appends the "omniarescue" parameter
to the bootargs variable. We do not want the user to be able to change
rescue mode bootargs. Therefore change this so that bootcmd sets the
bootargs variable in an absolute way (adding console device information
and the omniarescue paramterer).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
We always want to enumerate PCIe devices, because withouth this they
won't work in Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The board code reads MAC addresses from the ATSHA204A cryptochip.
For compatibility reasons the ethernet adapters on this SOC are not
enumerated in register address order. But when Omnia was first
manufactured this was done differently.
Change setting of MAC addresses to conform to the description on the
stickers sticked on actual Omnias.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
There is a Factory RESET button on the back side of the Turris Omnia
router. When user presses this button before powering the device up and
keeps it pressed, the microcontroller prevents the main CPU from booting
and counts how long the RESET button is being pressed (and indicates
this by lighting up front LEDs).
The idea behind this is that the user can boot the device into several
Factory RESET modes.
This patch adds support for U-Boot to read into which Factory RESET mode
the user booted the device. The value is an integer stored into the
omnia_reset environment variable. It is 0 if the button was not pressed
at all during power up, otherwise it is the number identifying the
Factory RESET mode.
This patch also changes bootcmd to a special hardcoded value if Factory
RESET button was pressed during device powerup. This special bootcmd
value sets the colors of all the LEDs on the front panel to green and
then tries to load the rescue image from the SPI flash memory and boot
it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
