Commit graph

31222 commits

Author SHA1 Message Date
Peter Tyser
9c06071a60 fsl_dma: Add bitfield definitions for common registers
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-01 23:01:55 -05:00
Peter Tyser
017f11f68e 8xxx: Break out DMA code to a common file
DMA support is now enabled via the CONFIG_FSL_DMA define instead of the
previous CONFIG_DDR_ECC

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-01 23:01:51 -05:00
Mark Jackson
6bbced6717 Atmel LCD driver GUARDTIME fix
This patch allows the guard time parameter to be set in
the Atmel LCDC driver.

By default, the previous value of 1 is used, unless the
setting is defined elsewhere.

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
2009-06-30 16:22:35 +02:00
Roy Zang
29c3518246 85xx: Add pci e1000 Ethernet support for P2020 board
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-30 08:26:34 -05:00
Kumar Gala
156984a361 8xxx: Fix PCI bus address setup for 36-bit configs
We want the outbound PCI memory map to end at the 4G boundary so we
can maximize the amount of space available for inbound mappings if
we have large amounts of memory.

This matches the device tree setup in the kernel for the 36-bit physical
configs for the platforms that have one (MPC8641 HPCN & MPC8572 DS).

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-30 08:24:22 -05:00
Kumar Gala
480f617905 86xx: Add CPU_TYPE_ENTRY support
Unify with 83xx and 85xx and use CPU_TYPE_ENTRY.  We are going to use
this to convey the # of cores and DDR width in the near future so its
good to keep in sync.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-30 08:24:22 -05:00
Peter Meerwald
98ab14e858 Blackfin: TWI/I2C: fix pure writes
If doing a pure write with register address and data (not a read/write
combo transfer), we don't set the initial transfer length properly which
ends up causing only the register address to be transferred.

While we're here, fix the i2c_write() parameter description of the buffer.

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-30 08:27:45 +02:00
Prafulla Wadaskar
5710de4580 spi: Add Marvell Kirkwood SPI driver
This patch adds a SPI driver for the Marvell Kirkwood SoC's.

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2009-06-26 00:59:09 +02:00
Minkyu Kang
6bde171a4c s3c64xx: move the reset_cpu function
Because of the reset_cpu is soc specific, should be move to soc
And read reset value from SYS_ID register instead of hard code
this patch also supports s3c6410

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-06-26 00:02:35 +02:00
Jean-Christophe PLAGNIOL-VILLARD
576afd4fae integrator: merge integratorap and integratorcp
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
46937b2742 integratorap/cp: use cfi driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
de7a01abd8 integratorap/cp/versatile: remove non used functions
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
f54851a6e3 integratorcp: split timer support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:03 +02:00
Jean-Christophe PLAGNIOL-VILLARD
2bcef0723e integratorap: split timer support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:03 +02:00
Jean-Christophe PLAGNIOL-VILLARD
86baa085c5 integratorap: split pci support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:03 +02:00
Ilya Yanok
379e9fc0a3 arm: add support for CONFIG_GENERIC_MMC
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-06-21 16:18:13 +02:00
Ilya Yanok
47d19da4d3 serial_mx31: allow it to work with mx27 too and rename to serial_mxc
UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-06-21 16:18:13 +02:00
Ilya Yanok
1dc4da749d mx27: basic cpu support
This patch adds generic code to support Freescale's i.MX27 SoCs.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-06-21 16:18:13 +02:00
Magnus Lilja
dd2f6965a6 i.MX31: Create a common device file.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2009-06-21 16:18:13 +02:00
Jean-Christophe PLAGNIOL-VILLARD
958f7da788 ARM: Add macros.h to be used in assembler file.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:12 +02:00
Magnus Lilja
40c642bc19 MX31: Add NAND SPL for i.MX31.
This patch adds the NAND SPL framework needed to boot i.MX31 boards
from NAND.

It has been tested on a i.MX31 PDK board with large page NAND. Small
page NANDs should work as well, but this has not been tested.

Note: The i.MX31 NFC uses a non-standard layout for large page NANDs,
whether this is compatible with a particular setup depends on how
the NAND device is programmed by the flash programmer (e.g. JTAG
debugger).

The patch is based on the work by Maxim Artamonov.

Signed-off-by: Maxim Artamonov <scn1874@yandex.ru>
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2009-06-21 16:18:12 +02:00
Magnus Lilja
df81238b3e ARM1136: Introduce CONFIG_PRELOADER macro.
Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's
in start.S. In preparation for adding support for NAND SPL
the macro CONFIG_PRELOADER is introducted and replaces the
CONFIG_ONENAND_IPL in start.S.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2009-06-21 16:18:12 +02:00
Jean-Christophe PLAGNIOL-VILLARD
8096c51fd4 at91: unify nor boot support
the lowlevel init sequence is the same so unify it

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:12 +02:00
Jean-Christophe PLAGNIOL-VILLARD
1b3b7c640d at91sam9263ek: add nor flash support
this will allow you to store use it for the env and to boot directly U-Boot from

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Ilko Iliev
3294923297 at91: add support for the PM9261 board of Ronetix GmbH
The PM9261 board is based on the AT91SAM9261-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Jean-Christophe PLAGNIOL-VILLARD
01550a2b65 pm9263: use macro instead of hardcode value for the lowlevel_init
optimize a few the RAM init

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Jean-Christophe PLAGNIOL-VILLARD
7a11c7f974 pm9263: lowlevel init update
move PSRAM init to pm9263.c
this will allow us after to make the nor lowlevel_init generic

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Mike Frysinger
3e88337b22 Blackfin: move ALL += u-boot.ldr to blackfin_config.mk
The way the ALL variable is used allows for config.mk's to add more
targets themselves without having to clutter up the top level Makefile.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15 13:30:27 -04:00
Mike Frysinger
afac8b0717 Blackfin: fix SPI flash speed define name
The SPI flash define is named CONFIG_SF_DEFAULT_SPEED, not
CONFIG_SF_DEFAULT_HZ, so fix the typos in the Blackfin boards.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15 13:30:21 -04:00
Mike Frysinger
9ae55ccf60 Blackfin: enable -O2 in lib_generic/ for ADI/Bluetechnix boards
Building the compression code in lib_generic/ with -O2 rather than -Os
gives a nice speed boost without too much code size increase.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15 13:30:19 -04:00
Mike Frysinger
fea63e2a44 Blackfin: bf548-ezkit: bump up monitor size
The latest version of U-Boot got a bit fatter in the BSS section which
caused overflows in the RAM region, so increase the monitor size.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15 13:30:18 -04:00
Vivi Li
bc43a8d899 Blackfin: bf533-stamp/bf537-stamp: fix env settings for SPI flash
The SPI flash layer is much stricter about sector usage than the eeprom
layer we used to use, so update the env settings to better match the
sector alignment of the flashes we use.

Signed-off-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15 13:30:16 -04:00
Vivi Li
63cb0f4eb2 Blackfin: bump up default JTAG console timeout
The debug tools that interface with the other side of the JTAG console
got much slower when generalizing things, so bump up the default timeout
value on the U-Boot side to cope.  Hopefully at some point we can improve
the debug tools to speed things back up.

Signed-off-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15 13:30:08 -04:00
Wolfgang Denk
57fe30194d Merge branch 'master' of /home/wd/git/u-boot/custodians 2009-06-15 11:16:04 +02:00
Wolfgang Denk
c9005a72fe Merge branch 'master' of git://git.denx.de/u-boot-net 2009-06-15 11:15:54 +02:00
Mike Frysinger
c11ff779f4 Blackfin: add jtagconsole helper script
This script is similar to the netconsole script, but instead works with
the JTAG console device driver that exists on Blackfin parts.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15 11:15:04 +02:00
Remy Bohmer
60f61e6d76 Convert DM9000 driver for CONFIG_NET_MULTI
All drivers need to be converted to CONFIG_NET_MULTI.
This patch converts the dm9000 driver.

Signed-off-by: Thomas Smits <ts.smits@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:55 -07:00
Prafulla Wadaskar
9131589ada net: Add Marvell Kirkwood gigabit ethernet driver
This patch adds a egiga driver for the Marvell Kirkwood SoC's.

Contributors:
Yotam Admon <yotam@marvell.com>
Michael Blostein <michaelbl@marvell.com

Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Acked-by: Stefan Rose <sr@denx.de>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:55 -07:00
s-paulraj@ti.com
7835f4b949 DaVinci Network Driver Updates
Different flavours of DaVinci SOC's have differences in their EMAC IP
This patch does the following
1) Updates base addresses for DM365
2) Updates MDIO frequencies for DM365 and DM646x
3) Update EMAC wrapper registers for DM365 and DM646x

Patch applies to u-boot-net git. the EMAC driver itself
will be updated shortly to add support for DM365 and DM646x

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:55 -07:00
Richard Retanubun
44578bea14 Subject: [PATCH] [repost] Standardize the use of MCFFEC_TOUT_LOOP as a udelay(1) loop counter.
From 584b5fbd4abfc43f920cc1c329633e03816e28be Mon Sep 17 00:00:00 2001
From: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Date: Wed, 20 May 2009 18:26:01 -0400
Subject: [PATCH] Standardize the use of MCFFEC_TOUT_LOOP as a udelay(1) loop counter.

Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:55 -07:00
Norbert van Bolhuis
c9a2aab151 A VLAN tagged DHCP request/discover is 4 bytes short
The problem is that BOOTP_SIZE uses ETHER_HDR_SIZE which is 14 bytes.
If sending a VLAN tagged frame (when env variable vlan is set) this
should be VLAN_ETHER_HDR_SIZE=18 which is what NetSetEther returns.

Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:55 -07:00
Ben Warren
6e0d2fc7fe Remove support for non-CONFIG_NET_MULTI on PPC4xx EMAC
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Ben Warren
8453587ef9 Switched davinci_emac Ethernet driver to use newer API
Added CONFIG_NET_MULTI to all Davinci boards
Removed all calls to Davinci network driver from board code
Added cpu_eth_init() to cpu/arm926ejs/cpu.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Ben Warren
8cc13c13f1 Initial cleanup of Davinci Ethernet driver
Removed pointless #ifdefs
 Moved functions around in file in preparation for switch to newer API

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Ben Warren
09cdd1b9b0 Moved Davinci Ethernet driver to drivers/net
This driver has been renamed davinci_emac.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Prafulla Wadaskar
6f51deb7f2 Marvell MV88E61XX Switch Driver support
Chips supported:-
1. 88E6161 6 port gbe swtich with 5 integrated PHYs
2. 88E6165 6 port gbe swtich with 5 integrated PHYs
2. 88E6132 3 port gbe swtich with 2 integrated PHYs
Platform specific configuration supported for:-
default or router port vlan configuration
led_init configuration
mdip/n polarity reversal configuration

Note: This driver is supported and tested against
kirkwood egiga interface

Contributors:
Yotam Admon <yotam@marvell.com>
Michael Blostein <michaelbl@marvell.com

Reviewed by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Zach LeRoy
091dc9f6ad tsec: Add support for BCM5482S PHY
Signed-off-by: Zach LeRoy <zleroy@xes-inc.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Mike Frysinger
9ff67e5e4c Blackfin: unify u-boot linker scripts
All the Blackfin linker scripts were duplicated across the board dirs with
no difference save from the semi-often used ENV_IS_EMBEDDED option.  So
unify all of them in the lib_blackfin/ dir and for the few boards that
need to embedded the environment directly, add a LDS_BOARD_TEXT define for
them to customize via their board config file.  This is much simpler than
forcing them to duplicate the rest of the linker script.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:14 -04:00
Mike Frysinger
f52efcae98 Blackfin: bf518f-ezbrd: enable SST SPI flash driver
The BF51xF parts have an internal SST SPI flash, so make sure the driver is
enabled by default so we can access it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:13 -04:00
Mike Frysinger
f348ab85f7 Blackfin: convert specific pre/post config headers to common method
The Blackfin port was using asm/blackfin-config-{pre,post}.h to setup
common Blackfin board defines.  The common method now is to use config.h,
so convert blackfin-config-post.h to that.  Rename the still Blackfin
specific blackfin-config-pre.h to config-pre.h so the naming conventions
at least line up.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:13 -04:00