This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that there is DM support in the RTC_MV driver update board configs
to use it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the gdsys Controlcenter DC specific build time kwbimage.cfg
generation code into the mach-mvebu/ directory to be shared by all 32bit
mvebu platforms.
Remove board specific kwbimage.cfg files, and use the generated one
instead. These files are all identical, with two exceptions. Clearfog
and Helios4 use the sdio boot device, whereas all others use spi. Update
the defconfigs for the exceptional boards to generate the same
kwbimage.cfg as before.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files
and point to origin internal board name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves the the config SYS_MALLOC_LEN to
Kconfig. It will be just for Zynq arch and to do
will be for all other archs.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_BLK config flag becomes mandatory, enable it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.
Add support for it.
The device tree is from Linux next-20180720.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Banana Pi M2 Ultra and M2 Berry are very similar boards. SATA can be
enabled exactly the same as for M2 Ultra introduced in
commit daa8b75a55 ("sunxi: enable SATA on Banana Pi M2 Ultra").
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
AXS10x boards have n25q512 spi flash IC, so add corresponding
nodes to device tree and enaple corresponding options in
defconfig.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With the pending requirement for CONFIG_BLK, this patch removes
the USB_STORAGE option which assumes that DM_USB is enabled, but isn't
yet available for the omap2340 musb glue among other issues. Once
the USB issues are resolved, a future patch can enable them again.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that TPMv1 and TPMv2 can be compiled at the same time, let's compile
them both with Sandbox as well as both drivers (and, it is already
implied in Kconfig: both commands).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A new defconfig is introduced to support SPL boot from QSPI NOR
flash. This is to support falcon mode for faster booting into
Linux.
Signed-off-by: York Sun <york.sun@nxp.com>
Move CONFIG_SPI_FLASH_SPANSION, CONFIG_SPI_FLASH, to defconfig.
Also disable disable 4K erase size option.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
4K erase size is used only in case of hydrid mode which is not
supported on any NXP platform with flash "s25fs512s".
Supported mode is uniform sector, with erase size 256kiB.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_SPL_FSL_LS_PPA is needed only in case of falcon boot
Support for this is not present in PPA currently, so
removing the default option from defconfig
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable "mtdparts" and "ubi" commands for uniphier_v8_defconfig to
use UBI on NAND devices.
Enable only "mtdparts" for uniphier_{v7,ld4_sld8}_defconfig because
enabling UBI would increase 170KB, which would be memory footprint
problem.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The NAND offsets for the kernel and U-Boot were missing.
This patch sets up the offsets so the AM3517-EVM can boot from NAND
when DIP switches S7:1 and S7:4 are to the OFF position
Signed-off-by: Adam Ford <aford173@gmail.com>
Only the MUSB driver is currently supported on the omap3_logic
boards. The driver is using the new-musb and not the legacy
version, so this patch removes the dead code references.
Signed-off-by: Adam Ford <aford173@gmail.com>
The m5253evbe board has been marked as orphan since June of 2014 and
should have been dropped a while ago. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
In preparation for delivery bottlenecks, enable support for GigaDevice, Macronix, and Winbond nor flash chips.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Since the vast majority of i.MX6 boards are migrating to SPL,
this patch converts im6q_logic to SPL and enables the SDP for
loading SPL and u-boot.img over USB. The Falcon mode only
supports NAND flash as of now due to limited space/RAM, but
all i.MX6D/Q SOM's from Logic PD have internal NAND from which
to boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
The new config skips the boot menu which asks which board is in
use. This is useful to allow direct booting of image without user
iteration.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This allow the addition of extra default configurations for each
baseboard, removing the boot menu when user boots for the first time.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the CAAM driver fails to be probed:
caam 30900000.caam: Entropy delay = 3200
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: failed to instantiate RNG
CAAM needs to be initialized in secure world, so enable
CONFIG_ARMV7_BOOT_SEC_DEFAULT to allow the driver to
probe successfully.
Tested with kernel mainline version 4.17.2.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx7d does not have a GPIO for selecting Falcon versus
normal mode, enter in Falcon mode when the customer selects
the CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the baseboards do not offer a way to autodetect which one is
in use, so we ask the user if no value has been set.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Convert pico-imx7d to SPL support.
There are two variants of pico-imx7d SOMs:
- One with 512MB of RAM
- One with 1GB of RAM
The 512MB module contains two Hynix H5TC2G63GFR-PBA.
The 1GB module contains two Hynix H5TC4G63GFR-PBA.
The RAM size is determined in runtime by reading GPIO1_12.
While at it, also add USB Serial Download mode support as it
is very helpful for loading SPL and u-boot.img via imx_usb_loader.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
fastboot tool is a convenient way to flash the eMMC, so
add support for it.
Examples of usages:
On the pico-imx7d U-Boot prompt:
=> fastboot 0
On the Linux PC connected via USB:
1. Retrieving the U-Boot version
$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.07-rc1-03888-gde846f9
finished. total time: 0.000s
2. Resetting the board
$ sudo fastboot reboot -i 0x0525
(this causes the pico-imx7d to reboot)
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This allow the use of:
> run setup_emmc
inside of the U-Boot prompt to do the partitioning of the disk.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This sets DISTRO_CONFIG and BOOTCOMMAND, as well as add a `finduuid`
environment helper to allow it to properly work with Yocto Project and
other distributions using extlinux autogenerated configuration files.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Enable the support for all SPI flash types.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
