Commit graph

22 commits

Author SHA1 Message Date
Heiko Schocher
17fa032671 serial, ns16550: bugfix: ns16550 fifo not enabled
commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.

Since the above patch, you have to setup the fcr register.

For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...

This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.

Detected this issue with automated tbot tests on am335x
based shc board.

The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)

Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-20 09:15:19 -05:00
Adam Ford
2f6ed3b89a ARM: Various: Future-proof serial platdata
A few boards still use ns16550_platdata structures, but assume the structure
is going to be in a specific order. By explicitly naming each entry,
this should also help 'future-proof' in the event the structure changes.

Tested on the Logic PD Torpedo + Wireless.

I only changed a handful of devices that used the same syntax as the Logic
board.  Appologies if I missed one or stepped on toes.  Thanks to Derald Woods
and Alexander Graf.

Signed-off-by: Adam Ford <aford173@gmail.com>

V6: Add fix to arch/arm/cpu/armv7/am33xx/board.c

V5: Add fix to arch/arm/cpu/arm926ejs/lpc32xx/devices.c

V4: Fix subject heading

V3: Remove  reg_offset out in all the structs. It was reverted out, and and if
it did exist, it would get initialized to 0 by default.

V2: I hastily copy-pasted the boards without looking at the UART number.
This addresses 3 boards that use UART3 and not UART1.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-03-14 19:18:48 -04:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Vladimir Zapolskiy
1222305b55 arm: lpc32xx: switch SPL builds to driver model
For NXP LPC32xx boards the change enables SPL_DM option, this allows
to use any driver model UART driver in SPL images, hence a restriction
on HSUART in SPL image is removed and well as definitions for non-DM
NS16550 driver, its DM version is used instead.

Because SPL_DM requires malloc(), enable CONFIG_SPL_SYS_MALLOC_SIMPLE
for LPC32xx boards.

The change adds about 5KB to the resulting SPL image (for devkit3250
board SPL image is increased from 10672 to 15608 bytes).

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-13 21:05:22 -05:00
Vladimir Zapolskiy
d25ba89e8b arm: lpc32xx: switch serial console to driver model
On NXP LPC32xx platform for non-SPL builds the change adds
standard (NS16550) and high-speed UARTs to driver model.
Due to specific of DM NS16550 device description UART clock can not be
got in runtime and by default it is set to 13MHz, if board PERIPH_CLK
is different, this should be specified in board configuration file.

For SPL builds HSUARTs are disabled and non-DM NS16550 driver is
compiled, if needed.

The change also updates default configs of devkit3250 and work_92105
boards to reflect updates in platform files.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-13 21:05:22 -05:00
Vladimir Zapolskiy
4c90234586 lpc32xx: fix calculation of HCLK PLL output clock
Execution branches on feedback mode are swapped, this has no effect
if default direct mode is on (then p_div is equal to 1 and Fout equals
to Fcco), that's why the problem remained unnoticed for a long time.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
2015-10-11 17:12:13 -04:00
Vladimir Zapolskiy
bab8d1e228 lpc32xx: remove duplicated DMA_CLK_ENABLE bit definition
Because there is an originally defined CLK_DMA_ENABLE macro in clk.h,
no reason to add another DMA_CLK_ENABLE macro with the same value.

Remove DMA_CLK_ENABLE, since it does not follow naming convention from
the code, this implies renaming of DMA_CLK_ENABLE to CLK_DMA_ENABLE in
lpc32xx/devices.c file.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-09-11 14:05:35 -04:00
Sylvain Lemieux
adf8d58d4f usb: lpc32xx: add host USB driver
Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.

The legacy driver was updated and clean-up as part of the integration with the latest u-boot.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
2015-08-18 13:45:57 -04:00
Sylvain Lemieux
980db8ca43 dma: lpc32xx: add DMA driver
Incorporate DMA driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx DMA driver
- lpc3250 header file DMA registers definition.

The legacy driver was updated and clean-up as part of the integration with the latest u-boot.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
2015-08-18 13:45:55 -04:00
Sylvain Lemieux
576007aec9 lpc32xx: cpu: add support for soft reset
Add support for optional soft reset (i.e. "RESOUT_N" not asserted during reset).

To be compatible with the original U-Boot code, when the "addr" parameter is 0, a hard is performed; for any other values, a soft reset is done.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-17 08:10:58 -04:00
Tom Rini
fcd78fa604 Merge branch 'master' of git://git.denx.de/u-boot-net 2015-08-13 07:19:41 -04:00
Vladimir Zapolskiy
dcfd37e5ef nand: lpc32xx: add SLC NAND controller support
The change adds support of LPC32xx SLC NAND controller.

LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.

This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.

Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.

The driver can be included to an SPL image.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-12 20:47:33 -04:00
Vladimir Zapolskiy
1a791892dc net: lpc32xx: add RMII phy mode support
LPC32xx MAC and clock control configuration requires some minor quirks
to deal with a phy connected by RMII.

It's worth to mention that the kernel and legacy BSP from NXP sets
SUPP_RESET_RMII == (1 << 11) bit, however the description of this bit is
missing in shared LPC32x0 User Manual UM10326 Rev. 3, July 22, 2011
and in LPC32x0 Draft User Mannual Rev. 00.27, November 20, 2008, also
in my tests an SMSC LAN8700 phy device connected over RMII seems to
work correctly without touching this bit.

Add support of RMII, if CONFIG_RMII is defined, this option is aligned
with a number of boards, which already define the same config value.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-11 13:43:04 -05:00
Albert ARIBAUD \(3ADEV\)
412ae53aad lpc32xx: add support for board work_92105
Work_92105 from Work Microwave is an LPC3250-
based board with the following features:
- 64MB or 128MB SDR DRAM
- 1 GB SLC NAND, managed through MLC controller.
- Ethernet
- Ethernet + PHY SMSC8710
- I2C:
  - EEPROM (24M01-compatible)
  - RTC (DS1374-compatible)
  - Temperature sensor (DS620)
  - DACs (2 x MAX518)
- SPI (through SSP interface)
  - Port expander MAX6957
- LCD display (HD44780-compatible), controlled
  through the port expander and DACs

This board has SPL support, and uses the LPC32XX boot
image format.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:23:39 +02:00
Albert ARIBAUD \(3ADEV\)
981219eebe lpc32xx: add LPC32xx SSP support (SPI mode)
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:23:20 +02:00
Albert ARIBAUD \(3ADEV\)
606f704760 lpc32xx: add GPIO support
This driver only supports Driver Model, not legacy model.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:23:09 +02:00
Albert ARIBAUD \(3ADEV\)
5e862b9539 lpc32xx: i2c: add LPC32xx I2C interface support
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:23:07 +02:00
Albert ARIBAUD \(3ADEV\)
c8381bf435 lpc32xx: mtd: nand: add MLC NAND controller
The controller's Reed-Solomon ECC hardware is
used except of course for raw reads and writes.
It covers in- and out-of-band data together.

The SPL framework is supported.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:22:56 +02:00
Albert ARIBAUD \(3ADEV\)
ac2916a224 lpc32xx: add Ethernet support
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:22:48 +02:00
Masahiro Yamada
d8769c62c1 arm926ejs: convert makefiles to Kbuild style
Note1:
In arch/arm/cpu/arm926ejs/spear/Makefile
START := start.o
was changed
extra-$(CONFIG_SPL_BUILD) := start.o
because spear/start.o is only used for SPL.

Note2:
START := start.o
was missing from arch/arm/cpu/arm926ejs/mxs/Makefile.
This commit simply adds
extra-$(CONFIG_SPL_BUILD) := start.o

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Vladimir Zapolskiy
52f69f818c arm926ejs: add NXP LPC32x0 cpu series support
This change adds initial support for NXP LPC32x0 SoC series.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-05-15 08:31:21 +02:00