As reported by Ilko Iliev <iliev@ronetix.at>, the "nand erase clean"
command is currently broken, and among other things causes all blocks
to be marked bad.
This implements it properly using MTD_OOB_AUTO, along with some
indentation fixes.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Hardware expects ECCM 0 for small page and ECCM 1 for large page
when booting from NAND, so use those defaults.
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
85xx can share them.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx).
The first command sent is NAND_CMD_READID.
Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id.
Tested with an MT29F4G08AAC.
Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This brings the core NAND code up to date with the Linux kernel.
Since there were several drivers in Linux as of the last update that are
not in u-boot, I'm not bringing over new drivers that have been added
since in the absence of an interested party.
I did not update OneNAND since it was recently synced by Kyungmin Park,
and I'm not sure exactly what the common ancestor is.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The existing code has a few errors that need to be fixed in
order to support large RAM sizes. Fix those, and add a
comment to make it clearer.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
If the board _didn't_ request INVLINE_INVERTED, we set INVLINE_INVERTED,
otherwise we don't. WTF?
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
atmel_lcdfb doesn't actually need anything from asm/arch/hardware.h. It
includes a file that does, asm/arch/gpio.h, but this file doesn't
include <asm/arch/hardware.h> like it's supposed to.
Add the missing include to asm/arch/gpio.h and remove the workaround
from the atmel_lcdfb driver. This makes the driver compile on avr32.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add a common setup function that determines the pci_region(s) based
on how much memory we have in the system.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
* PCI Inbound window was setup incorrectly. The PCI address and system
address were swapped. The PCI address should be setting piwar/piwbear
and the system address should be setting pitar.
* Removed masking of addresses to allow for system address to support
system address & PCI address >32-bits
* Set PIWBEAR & POTEAR to allow for full 64-bit PCI addresses
* Respect the PCI_REGION_PREFETCH for inbound windows
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
PCI bus is inherently 64-bit. While not all system require access to
the full 64-bit PCI address range some do. This allows those systems
to enable the full PCI address width via CONFIG_SYS_PCI_64BIT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Debug sessions may have left enabled laws.
Changing lawbar with an unkown enabled tgtid could cause problems.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch fixes the following warnings, when using
the soft_i2c driver using no CPU pins on MPC82xx or MPC8xx
systems:
soft_i2c.c: In function 'send_reset':
soft_i2c.c:93: warning: unused variable 'immr'
soft_i2c.c: In function 'send_start':
soft_i2c.c:124: warning: unused variable 'immr'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:146: warning: unused variable 'immr'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:171: warning: unused variable 'immr'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:196: warning: unused variable 'immr'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:244: warning: unused variable 'immr'
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds support for the National LM63 temperature
sensor with integrated fan control. It's used on the GDSys
Neo board (405EP) which will be submitted later.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Stefan Roese <sr@denx.de>
Added as a convenience for other platforms that uses MPC8360 (has 8 UCC).
Six eth interface is chosen because the platform I am using combines
UCC1&2 and UCC3&4 as 1000 Eth and the other four UCCs as 10/100 Eth.
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Change UEC phy interface from GMII to RGMII on MPC8568MDS board
Because on MPC8568MDS, GMII interface is only recommended for 1000Mbps speed,
but RGMII interface can work at 10/100/1000Mbps, and RGMII interface works more stable.
Now both UEC1 and UEC2 can work properly under u-boot.
It is also in consistent with the kernel setting for 8568 UEC phy interface.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The function parse_line() in common/main.c was exposed globally by commit
6636b62a6e, Result in conflict with the same
name funciton in drivers/bios_emulator/x86emu/debug.c when define the DEBUG.
This patch fix this by renaming the function in the debug.c file.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
At a lot of places in the code the PIPE_INTERRUPT flags and friends
are used wrong. The wrong bits are compared to this flag resulting
in wrong conditions. Also there are macros that should be used for
PIPE_* flags.
This patch tries to fix them all, however, I was not able to test the
changes, because I do not have any of these boards.
Review required!
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
The max packet size is encoded as 0,1,2,3 for 8,16,32,64 bytes.
At some places directly 8,16,32,64 was used instead of the encoded
value. Made a enum for the options to make this more clear and to help
preventing similar errors in the future.
After fixing this bug it became clear that another bug existed where
the 'pipe' is and-ed with PIPE_* flags, where it should have been
'usb_pipetype(pipe)', or even better usb_pipeint(pipe).
Also removed the triple 'get_device_descriptor' sequence, it has no use,
and Windows nor Linux behaves that way.
There is also a poll going on with a timeout when usb_control_msg() fails.
However, the poll is useless, because the flag will never be set on a error,
because there is no code that runs in a parallel that can set this flag.
Changed this to something more logical.
Tested on AT91SAM9261ek and compared the flow on the USB bus to what
Linux is doing. There is no difference anymore in the early initialisation
sequence.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
The checks for CFG_EEPROM_PAGE_WRITE_ENABLE and
CFG_EEPROM_PAGE_WRITE_BITS in various temperature
sensor drivers are not necessary
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
When the total size of all NAND devices exceeds 4 GiB, the size will
overflow. This patch tries to fix this.
Note that we still have a problem when a single NAND device is bigger
than 4 GiB: then the overflow would actually happen earlier, i. e.
when storing the size in nand_info[].size, as nand_info[].size is an
"u_int32_t".
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Currently VSC8601 doesn't link with 10/100M partners if the
EEPROM/Strapping is not set up.
Setting the auto-neg register fixes this.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
get_prom function was used __attriute__ , but it is not enable.
ax88796.o does not do link besides ne2000.o. When ld is carried
out, get_prom function of ax88796.c is ignored.
This problem is a thing by specifications of ld.
I checked and test this patch on SuperH and MIPS.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The flash_unlock_seq requires a sector for AMD_LEGACY.
Fix a retcode check typeo.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The CFI flash driver starts at flash_init() which calls down into
flash_get_size(). This starts by calling flash_detect_cfi(). If said
function fails, flash_get_size() finishes by attempting to reset the
flash. Unfortunately, it does this with an info->portwidth set to 0x10
which filters down into flash_make_cmd() and that happily smashes the
stack by sticking info->portwidth bytes into a cfiword_t variable that
lives on the stack. On a 64bit system you probably won't notice, but
killing the last 8 bytes on a 32bit system usually leads to a corrupt
return address. Which is what happens on a Blackfin system.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch refactors some large routines of the USB OHCI code by
making some routines smaller and more readable which helps
debugging and understanding the code. (Makes the code looks
somewhat more like the Linux implementation.)
Also made entire file compliant to Linux Coding Rules (checkpatch.pl compliant)
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
