Each line should be terminated by semi-colon. It was not caught
earlier as there is a proper statement. Fix it by changing the
comma with semi-colon.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. This is controlled by pcf gpio line. Add
appropriate mode-gpios DT entry so that driver can select the required
slave.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
On DRA72 EVM, cpsw slaves may be muxed with other modules. This
selection is controlled by a pcf gpio line. Add support for cpsw driver
to acquire mode-gpios and select the appropriate slave using gpio APIs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
PCF8575 does not have any registers hence, offset field needs to be
ignored for i2c read/write. Therefore populate u-boot,i2c-offset-len
with 0 in PCF8575 DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On DRA7, pcf chip present at address 0x21 on i2c1, is used to
switch between cpsw slave0 and slave1. Hence, enable PCF
driver for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
TI's PCF8575 is a 16-bit I2C GPIO expander.The device features a
16-bit quasi-bidirectional I/O ports. Each quasi-bidirectional I/O can
be used as an input or output without the use of a data-direction
control signal. The I/Os should be high before being used as inputs.
Read the device documentation for more details[1].
This driver is based on pcf857x driver available in Linux v4.7 kernel.
It supports basic reading and writing of gpio pins.
[1] http://www.ti.com/lit/ds/symlink/pcf8575.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
The devicetrees for various platforms already exceed 16k. Add a define
CONFIG_SYS_FDT_SIZE to specify the FDT size, and set to 16k for the
two boards that define this CONFIG_SYS_FDT_BASE parameter. This
allows platforms with larger devicetree blobs to boot from NOR.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Ensuring the baudrate divisor value doesn't exceed the max value
in the calculation.It will be capped at max value to ensure the
correct value being written into the register.
Example of the existing bug is when calculated div = 16. After and
with the mask, the value written to register is actually 0 (register
field for baudrate divisor). With this fix, the value written is now
15 which is max value for baudrate divisor.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
This option controls how long it should be paused before entering
the auto-boot mode. The default value from Kconfig should be fine
except socfpga_vining_fpga_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We no longer need to set 'caps' as it's not passed to sdhci_setup_cfg
anymore.
Fixes: 14bed52d27 ("mmc: sdhci: remove the unnecessary arguments for
sdhci_setup_cfg")
Signed-off-by: Tom Rini <trini@konsulko.com>
This follows 9fd383724c ("mmc: don't allow extra cmdline arguments"),
and affects omapl138_lcdk and omap3_evm_quick_mmc.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Inform getopt that '-c' requires a parameter.
Fixes: a02221f29d ("mkimage: Convert to use getopt()")
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Return one string for each command that was executed. This seems cleaner.
Suggested-by: Teddy Reed <teddy.reed@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add a proper function for this rather than using internal functions. Use it
in the single call site.
Also, do a restart at the end of the vboot test to reset to the normal
device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Stephen Warren <swarren@nvidia.com>
Use 'cons.log.section' feature to split up the test output. This makes it
easier to read.
Suggested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename this argument and pass it to each function that needs it, instead of
making it global.
Suggested-by: Stephen Warren <swarren@nvidia.com>
Suggested-by: Teddy Reed <teddy.reed@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of this, use the existing run_and_log() function, enhanced to
support a command string as well as a list of arguments.
Suggested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix some typos in various files introduced with the vboot test conversion.
Reported-by: Teddy Reed <teddy.reed@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This check was missed. Add it and make the message more verbose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
Fixes: 9e17b034 (test/py: Provide a way to check that a command fails)
Fix review comments that were missed at the time. Also explain why we need
to regenerate the device tree for each test.
Reported-by: Teddy Reed <teddy.reed@gmail.com>
Suggested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: f6349c3c (test: Add a README)
Add this shortcut for running tests. Unfortunately 'make test' cannot be
used as it is an existing directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Teddy Reed <teddy.reed@gmail.com>
We create 2 sets of page tables: One for normal operation, one for
emergency (used while modifying the former).
Because the page tables grow dynamically, we have code that checks
for overflow. Unfortunately we didn't adjust the available space
variable while creating the emergency tables, so potentially someone
might run into an overflow there (not seen in real world yet though!).
Fix it by properly adjusting the size as well as the base offset in
emergency page table creation.
Reported-by: York Sun <york.sun@nxp.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
The calculation of "dev_desc->lba - 34 - 1 - offset" is not correct for
size '-', because both fist_usable_lba and last_usable_lba will remain
34 sectors.
We can simply use 0 for size '-' because the part_efi module will decode
the size and auto extend the size to maximum available size.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features. At this point in time they no longer serve a good purpose so
remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
The already available ilog2 function does exactly the same in the common
case than the log2 function the current clock-driver reimplement.
So, simply move to that one.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Enable the rockchip dwmmc driver for rk3399 and its evb.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
rk3399 sdcard is using dwmmc controller, enable it for sdcard.
SCLK_SDMMC is the clock for controller operation clock, move it
to the first place.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
MMC core will use 400KHz for card initialize first and then switch to
higher frequency like 50MHz, we need to support both 400KHz and about
50MHz for dwmmc controller.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
To compatible with distro boot, we need to add gpt and fs support,
including gpt table and vfat, ext2, ext4 support.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Enable ums feature for rk3288 boards, so that we can mount the mmc
device to PC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
For compatibility with distro boot, fastboot, and mount the mmc deivce
to PC via usb mass storage feature, GPT partitions are essential.
You should write the partitions to mmc device prior to use above
feature.
=> gpt write mmc 1 $partitions
GPT successfully written to block device!
success!
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
With the number of Rockchip clock drivers increasing, don't clutter up
the core drivers/clk directory with them and instead move them out of
the way into a separate subdirectory.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Updated for rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an extra byte so that this data is not byteswapped.
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable fastboot feature on rk3036, please refer to doc/README.rockchip
for more detailed usage.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When disabled CONFIG_MMC_SDMA, variable caps didn't use.
This patch fixes the compiler error for -Wunused-but-set-variable
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
In the case of omap3 we have a number of platforms that are close to
exceeding SRAM limits, depending on compiler. Move to USE_TINY_PRINTF
to give them more room. OMAP4 will soon enough be in a similar place,
so enable that now.
Signed-off-by: Tom Rini <trini@konsulko.com>
print_std_bdinfo outputs typical set of board information entries:
boot params location, memory and flash addresses and sizes, network
interfaces information and configured serial baud rate.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
print_baudrate outputs serial baud rate.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
print_eth_ip_addr outputs eth configurations for up to 6 interfaces and
configured IP address.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
print_bi_flash outputs flashstart, flashsize and flashoffset lines.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
print_bi_dram outputs start address and size for each DRAM bank.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
print_bi_mem outputs memstart and memsize lines.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.
Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.
I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.
CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.
Fixes: 95ebc253e6 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
