In order to make the ecclayout definition completely dynamic we need to
rework the way the OOB layout are defined and iterated.
Create a few mtd_ooblayout_xxx() helpers to ease OOB bytes manipulation
and hide ecclayout internals to their users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 75eb2cec251fda33c9bb716ecc372819abb9278a]
[masahiro:
cherry-pick more code from adbbc3bc827eb1f43a932d783f09ba55c8ec8379]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If your controller already sends the required NAND commands when
reading or writing a page, then the framework is not supposed to
send READ0 and SEQIN/PAGEPROG respectively.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 3371d663bb4579f1b2003a92162edd6d90edd089]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add the tR_max, tBERS_max, tPROG_max and tCCS_min timings to the
nand_sdr_timings struct.
Assign default/safe values for the statically defined timings, and
extract them from the ONFI parameter table if the NAND is ONFI
compliant.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[Linux commit: 204e7ecd47e26cc12d9e8e8a7e7a2eeb9573f0ba
Fixup commit: 6d29231000bbe0fb9e4893a9c68151ffdd3b5469]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When changing from one data interface setting to another, one has to
ensure a specific sequence which is described in the ONFI spec.
One of these constraints is that the CE line has go high after a reset
before a command can be sent with the new data interface setting, which
is not guaranteed by the current implementation.
Rework the nand_reset() function and all the call sites to make sure the
CE line is asserted and released when required.
Also make sure to actually apply the new data interface setting on the
first die.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd8311 ("mtd: nand: automate NAND timings selection")
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[Linux commit: 73f907fd5fa56b0066d199bdd7126bbd04f6cd7b]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The NAND framework provides several helpers to query timing modes supported
by a NAND chip, but this implies that all NAND controller drivers have
to implement the same timings selection dance. Also currently NAND
devices can be resetted at arbitrary places which also resets the timing
for ONFI chips to timing mode 0.
Provide a common logic to select the best timings based on ONFI or
->onfi_timing_mode_default information. Hook this into nand_reset()
to make sure the new timing is applied each time during a reset.
NAND controller willing to support timings adjustment should just
implement the ->setup_data_interface() method.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[Linux commit: d8e725dd831186a3595036b2b1df9f68cbc6efa3]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The nand layer will need ONFI mode 0 to use it as timing mode
before and right after reset.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 6e1f9708dbf3c50a8da93c1952a01a7a2acb5e66]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
struct nand_data_interface is the designated type to pass to
the NAND drivers to configure the timing. To simplify further
patches convert the onfi_sdr_timings array from type struct
nand_sdr_timings nand_data_interface.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: b1dd3ca203fccd111926c3f6ac59bf903ec62b05]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently we have no data structure to fully describe a NAND timing.
We only have struct nand_sdr_timings for NAND timings in SDR mode,
but nothing for DDR mode and also no container to store both types
of timing.
This patch adds struct nand_data_interface which stores the timing
type and a union of different timings. This can be used to pass to
drivers in order to configure the timing.
Add kerneldoc for struct nand_sdr_timings while touching it anyway.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: eee64b700e26b9bcc6fce024681c31f5e12271fc]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When NAND devices are resetted some initialization may have to be done,
like for example they have to be configured for the timing mode that
shall be used. To get a common place where this initialization can be
implemented create a nand_reset() function. This currently only issues
a NAND_CMD_RESET to the NAND device. The places issuing this command
manually are replaced with a call to nand_reset().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 2f94abfe35b210e7711af9202a3dcfc9e779219a]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
'extern' is not necessary for function declarations. To prevent
people from adding the keyword to new declarations remove the
existing ones.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 79022591839f110f465cac0223e117b91d47d5db]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The generic NAND DT bindings allows one to tweak the ECC strength and
step size to their need. It can be used to lower the ECC strength to
match a bootloader/firmware config, but might also be used to get a better
reliability.
In the latter case, the user might want to use the maximum ECC strength
without having to explicitly calculate the exact value (this value not
only depends on the OOB size, but also on the NAND controller, and can
be tricky to extract).
Add a generic 'nand-ecc-maximize' DT property and the associated
NAND_ECC_MAXIMIZE flag, to let ECC controller drivers select the best
ECC strength and step-size on their own.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
[Linux commit: ba78ee00e1ff84de9b3ad33edbd3ec599099ee82]
[masahiro: of_property_read_bool -> fdt_getprop for U-Boot]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add stubs to the header in case CONFIG_SYS_NAND_ONFI_DETECTION is
disabled. This is much easier than adding around #ifdef to the
caller side.
Also, I removed the #ifdef around onfi_params. In Linux, onfi_params
and jedec_params are unified as union. It will be the right thing
to do.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Same macros are defined in various places. Collect them into
include/linux/bitops.h like Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These boards are on the boundary of "u-boot-nodtb.bin exceeds file
size limit" error.
Reduce the log-level to save memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This option prevents booting on am335x_evm at least along with most
likely other platforms.
Fixes: 337bbb6297 ("spl: fit: add SPL_FIT_IMAGE_TINY config to reduce code-size")
Signed-off-by: Tom Rini <trini@konsulko.com>
icorem6 has sd on usdhci1 which is devno 0 so return proper
devno from board_mmc_get_env_dev for icorem6 and icorem_6rqs
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add new board names for existing board support
imx6q - icore and icore_rqs boards
imx6ul - geam6ul and isiot boards
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
As per USDHC boot eFUSE descriptions:
USDHC3 => devno 2
USDHC4 => devno 3
Linux will detect mmc0, mmc1, mmc2 based on the status
"okay" on usdhc so imx6qdl-icore-rqs.dtsi has enabled
usdhc1, usdhc3 and usdhc4.But U-Boot can detect based
on the aliases so add mmc1, mmc2 for usdhc3 and usdhc4
respectively and return the board_mmc_get_env_dev
by subtracting -1
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
before relocation pinctrl data BSS is overlapping DT area,
when .data is using uninitialized global variable,
imx6_pinctrl_soc_info. So assign them flags ZERO_OFFSET_VALID
to prevent BSS overlap
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
mx6sxsabresd can run different kernel versions, such as NXP 4.1 or mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the SD
card changes depending on the kernel version.
In order to avoid such issue, use the UUID method to specify the
rootfs location.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.
It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.
While at it, rename it to imx_wdog_disable_powerdown().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Clear powerdown enable bit for WDOG3 on i.MX6ULL to avoid unwanted
kernel reboots.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The boot (and fallback/emergency boot) concept for the RK3399-Q7
differs from Rockchip's reference platforms.
On the RK3399-Q7, some of this functionality is present in the
bootloader itself (and configurable); some is backed in hardware by
the Qseven BIOS_DISABLE signal to invoke the final stages of fallbacks
(i.e. either an external boot bypassing on-module memories or falling
back to the BROM for USB recovery).
In summary: the ADC-based boot_mode check does not apply for the
RK3399-Q7 and we therefore disable it (in this commit) by setting
CONFIG_BOOT_MODE_REG to 0.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The ROCKCHIP_BOOT_MODE_REG option defaults to a hex value, so 0 will
show as 0x0 if a default is provided and changed via Kconfig.
However, it still will show as 0, if no default is given.
Consequently, the "is set to something other than 0" test in a
Makefile is cumbersome. Instead this check can easily be performed in
the C-code.
This removes the ifeq-check from mach-rockchip/Makefile, adds a
matching #if-check to boot_mode.c and fixes resulting link issues (if
boot_mode.o was not included due to the Makefile check) by defining a
stub function (in case the functionality is not built in) for
setup_boot_mode in boot_mode.c.
Fixes: e306779 (rockchip: make boot_mode related codes reused across all platforms)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3399 has a total of 9 I2C controllers. To support these, the
enum in periph.h is extended and the mapping from the IRQ numbers to
the peripheral-ids is extended to ensure that pinctrl requests are
passed through to the function configuring the I2C pins.
For I2C8, the pinctrl is implemented and tested (on a RK3399-Q7) using
communication with the FAN53555 connected on I2C8.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The RK3399 clk driver still has a left-over use of extract_bits, which
can be replaced by using bitfield_extract from include/bitfield.h.
This rewrites the invocation to use the shared function.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
A minor code-size increase from the changes for tracking the os-type
of FIT images and from infrastructure for recording the loadables into
the the loaded FDT, broke the builds for sun50i and some OMAP2+ devices.
This change adds a new config option (enabled by default for
MACH_SUN50I, MACH_SUN50I_H5 and ARCH_OMAP2PLUS) that does skips these
processing steps (bringing code size down to below the limit
again). The os-type is not evaluated, but assumed to be IH_OS_UBOOT
(i.e. taking the code-paths intended for backward-compatibility).
Note that enabling this config option precludes any useful downstream
processing, such as utilising a special calling convention for ATF or
OPTEE, based on the os-type of the loadables.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This tracks the SPL changes for ATF for the RK3368-uQ7:
* renames ATF_SUPPORT to ATF
* drops CONFIG_SPL_ATF_TEXT_BASE (now dynamically retrieved from
the .itb file)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This defconfig update makes use of the new features:
* CONFIG_ROCKCHIP_SPL_RESERVE_IRAM is now set to 0, as there is no
overlap between the M0 firmware and the ATF (we load this to DRAM
and relocate it to its final location within the ATF)
* tracks the ATF_SUPPORT -> ATF renaming
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For the RK3368-uQ7, we can now update the .its file to mark the
Trusted Firmware as out 'firmware' bootable and annotate both ATF and
U-Boot with an OS-type.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit updates the .its file for the RK3399-Q7 to use the new
features and demonstrates how to use those:
* it marks the ATF as the 'firmware'
* it tracks the OS-type for U-Boot and ATF
* it loads the PMU (M0) firmware to DRAM and records the location
to /fit-images (where our ATF reads it from)
With the handoff of the next-stage FDT to ATF in place, we can now use
this to pass information about the load addresses and names of each
loadables to ATF: now we can load the M0 firmware into DRAM and avoid
overwriting parts of the SPL stage. This is achieved by changing our
.its-file to use an available area of DRAM as the load-address.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This tracks the SPL changes for ATF for the Firefly:
* renames ATF_SUPPORT to ATF
* drops CONFIG_SPL_ATF_TEXT_BASE
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SPL_ATF_TEXT_BASE configuration item has become obsolete.
Remove it from Kconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Having CONFIG_SPL_ATF seems more natural.
Rename it, while it it is easy and there's few boards that use it
(only RK3399 and RK3368 boards).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new interface spl_invoke_atf() that takes a spl_image_info
argument and then derives the necessary parameters for the ATF entry.
Based on the additional information recorded (into /fit-images) from
the FIT loadables, we can now easily locate the next boot stage.
We now pass a pointer to a FDT as the platform-specific parameter
pointer to ATF (so we don't run into the future headache of every
board/platform defining their own proprietary tag-structure), as
FDT access is already available in ATF.
With the necessary infrastructure in place, we can now update the
support for the ARM Trusted Firmware to dispatch into the
spl_invoke_atf function only if a IH_OS_ARM_TRUSTED_FIRMWARE image is
loaded.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If a FDT was loaded (e.g. to append it to U-Boot image), we store it's
address and record information for all loadables into this FDT. This
allows us to easily keep track of images for multiple privilege levels
(e.g. with ATF) or of firmware images preloaded into temporary
locations (e.g. PMU firmware that may overlap the SPL stage).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
During the loading of more complex FIT images (e.g. when the invoked
next stage needs to find additional firmware for a power-management
core... or if there are multiple images for different privilege levels
started in parallel), it is helpful to create a record of what images
are loaded where: if a FDT is loaded for one of the next stages, it
can be used to convey the status and location of loadables.
This adds a fdt_record_loadable() function that can be invoked to
record the status of each loadable below the /fit-images path.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To better support bootin through an ATF or OPTEE, we need to
streamline some of the logic for when the FDT is appended to an image:
depending on the image type, we'd like to append the FDT not at all
(the case for the OS boot), to the 'firmware' image (if it is a
U-Boot) or to one of the loadables (if the 'firmware' is an ATF, an
OPTEE, or some other image-type and U-Boot is listed in the
loadabled).
To achieve this goal, we drop the os_boot flag and track the type of
image loaded. If it is of type IH_OS_U_BOOT, we append the FDT.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mainly a stylistic change: convert the load_addr and entry_point
fields of struct spl_image_info to uintptr_t (from ulong).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When loading a full U-Boot with detached device-tree using the SPL FIT
backend, we should store the address of the FDT loaded as part of the
SPL image info: this allows us to fixup the FDT with additional info
we may want to propagate onward.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To boot on ARMv8 systems with ARM Trusted Firmware, we need to
assemble an ATF-specific parameter structure and also provide the
address of the images started by ATF (e.g. BL3-3, which may be the
full U-Boot).
To allow us to identify an ARM Trusted Firmware contained in a FIT
image, this adds the necessary definitions.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
