Supported boot device types in iMX8MP: MMC.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is
for command fstype.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution. kernel_addr_r is the location in RAM where
the kernel will be loaded to. Delete unnecessary environment variables
because "run distro_bootcmd" is set to be the default boot mode.
On the iMX8MP platform I used, "mmc1" represents SD card and "mmc2"
represents eMMC.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
When booting imx8mp-evk the following allocation error
message is seen:
U-Boot 2021.01-rc3-00200-ge668bec96a5f (Dec 21 2020 - 14:36:42 -0300)
alloc space exhausted
Fix it by increasing CONFIG_SYS_MALLOC_F_LEN to 0x10000 like it
is done on other i.MX8MM/8MN boards.
Reported-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
i.MX8M series includes support for high speed modes in uSDHC controllers.
Turn on corresponding configuration options for EVK boards, which would
enable high speed modes to be included in U-Boot.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.
When OPTEE memory is removed from first bank, it may split the first bank
to two banks, adjust the MMU table for the split case,
Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge
i.MX8MP evk to default to avoid issue.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Tested-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot-spl.bin pad with ddr firmware conflicts with the
CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten
by malloc in SPL stage and cause ddr initialization not able
to finish. So update the related addresses to fix the issue.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
It is safe to run SPL with caches enabled on i.MX8, so
remove such restriction.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
