This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.
CAN is available on AT91SAM9263 and AT91CAP9 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Added CONFIG_NET_MULTI to all Davinci boards
Removed all calls to Davinci network driver from board code
Added cpu_eth_init() to cpu/arm926ejs/cpu.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
all arm init the IRQ stack the same way
so unify it in lib_arm/interrupts.c and then call arch specific interrupt init
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
all arm boards except a few use the same cpu linker script
so move it to cpu/$(CPU)
that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Once the Davinci watchdog has been enabled, the timeout
value cannot be changed. If the timeout in use is long,
it can take a long time for card to reset. By writing
an invalid service key, we can trigger an immediate reset.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
The u-boot.lds is common for all DaVinci boards. The patch removes
multiple instances and moves the u-boot.lds to /cpu/arm926ejs/davinci
folder. This addresses one of the comments i received while submitting
patches for DM3xx
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Move the clock-rate dumping code into the cpu/.../davinci area
where it should have been, enabled by CONFIG_DISPLAY_CPUINFO,
updating the format and showing the DSP clock (where relevant).
Switch boards to use the cpuinfo() hook for this stuff.
Remove a few now-obsolete PLL #defines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
actually the timer init use the interrupt_init as init callback
which make the interrupt and timer implementation difficult to follow
so now rename it as int timer_init(void) and use interrupt_init for interrupt
btw also remane the corresponding file to the functionnality implemented
as ixp arch implement two timer - one based on interrupt - so all the timer
related code is moved to timer.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add some basic declarations for DaVinci DM355/DM350/DM335 support,
keyed on CONFIG_SOC_DM355. (DM35X isn't quite right because the
DM357 is very different; while the DM355 is like a DM355 without
the MPEG/JPEG coprocessor).
These have different peripherals than the DM6446, and some of
the peripherals are at different addresses. Notably for U-Boot,
there's no EMAC, and the NAND controller address is different
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix two buglets in the dm644x support: don't set two must-be-zero
bits in the UART management register; and only include the I2C hooks
if the I2C driver is being included.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Split out DaVinci DM6446-specific bits from more generic bits:
- Add a CONFIG_SOC_DM644X. All current boards use DM6446 chips;
DM6443 and DM6441 chips differ in available peripherals.
- Move most DM644X-specific bits from psc.c to a new dm644x.c file,
which is conditionally built. It provides device-specific setup.
Plus minor coding style and comment updates with respect to the PSC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Update cpu/arm926ejs/davinci/Makefile to use COBJ-y type syntax.
Add the first conditional: for EMAC driver support. Not all
chips have an EMAC; and boards might not use it, anyway.
This doesn't touch PHY configuration; that should eventually
become conditional too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move DaVinci PSC support from board/* to cpu/* where it belongs.
The PSC module manages clocks and resets for all DaVinci-family
SoCs, and isn't at all board-specific.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't needlessly include lowlevel init code; that's only really
needed with boot-from NOR (not boot-from-NAND). The 2nd stage
loader (UBL) handles that before it loads U-Boot.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
AFEB9260 uses PA10, PA11 for ETX2 and ETX3.
Also, due to extarnal pull-up on IRQ line, Micrel PHY ID is 1 after reset sequence,
not 0.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
lowlevel_init.S is not used any more so remove it.
As consequence, we also don't have to generate u-boot.lds
but can use a static version as before.
This also fixes the out-of-tree build problem introduced
with commit f0a2c7b4 "at91: add support for the PM9263 board"
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
The timer has been rewrote with a precision at ~0,18%
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Eric BENARD <ebenard@free.fr>
The PM9263 board is based on the AT91SAM9263-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Divisor field is called PTV not PVT.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
