Add initial support for STM32MP2 SoCs family.
SoCs information are available here :
https://www.st.com/content/st_com/en/campaigns/microprocessor-stm32mp2.html
Migrate all MP1 related code into stm32mp1/ directory
Create stm32mp2 directory dedicated for STM32MP2 SoCs.
Common code to MP1, MP13 and MP25 is kept into
arch/arm/mach-stm32/mach-stm32mp directory :
- boot_params.c
- bsec
- cmd_stm32key
- cmd_stm32prog
- dram_init.c
- syscon.c
- ecdsa_romapi.c
For STM32MP2, it also :
- adds memory region description needed for ARMv8 MMU.
- enables early data cache before relocation.
During the transition before/after relocation, the MMU, initially setup
at the beginning of DDR, must be setup again at a correct address after
relocation. This is done in enables_caches() by disabling cache, force
arch.tlb_fillptr to NULL which will force the MMU to be setup again but
with a new value for gd->arch.tlb_addr. gd->arch.tlb_addr has been
updated after relocation in arm_reserve_mmu().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The migration deadline for moving to DM_SCSI was v2023.04. A further
reminder was sent out in August 2023 to the remaining platforms that had
not migrated already, and that a few more over the line (or configs
deleted).
With this commit we:
- Rename CONFIG_DM_SCSI to CONFIG_SCSI.
- Remove all of the non-DM SCSI code. This includes removing other
legacy symbols and code and removes some legacy non-DM AHCI code.
- Some platforms that had previously been DM_SCSI=y && SCSI=n are now
fully migrated to DM_SCSI as a few corner cases in the code assumed
DM_SCSI=y meant SCSI=y.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is not used for sandbox, so drop it. Enable the things that it
controls to avoid dstrastic changes in the config settings for
sandbox builds.
The end result is that these are enabled:
BOOTMETH_DISTRO
BOOTSTD_DEFAULTS
and these are disabled:
USE_BOOTCOMMAND
BOOTCOMMAND (was "run distro_bootcmd")
DISTRO_DEFAULTS
Note that the tools-only build has already disabled DISTRO_DEFAULTS
and BOOTSTD_FULL
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for the Inteno XG6846 board based on the
Broadcom MIPS 6328 SoC.
The default boot will read a uImage from flash and boot it.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move ASUS Transformers, Grouper, P895 and P880 config fragments into
their respective device directory in /board/../configs/
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Convert refresh USB to enter console. Transformers have full size
USB and a dock keyboard so access to U-Boot console would be handy.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Change boot logic to primary try to boot from USB in dock, then
from microSD and lastly from eMMC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Enables JH7110 RNG driver to visionfive2 board.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
enable PSCI reset used for the system reset
Even though Corstone-1000 does not implement the entire PSCI APIs,
it relies on PSCI reset interface for the system reset.
Signed-off-by: Emekcan Aras <emekcan.aras@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
unzip the kernel before executing it
The Corstone-1000 kernel has become too large to fit in the available
storage. Switching to a compressed kernel avoids the problem, but
requires uncompressing it.
Changes made are generated using savedefconfig.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
QEMU print and console buffer sizes have been restricted on QEMU below
their default values.
One of the side effects of the print buffer size restriction is output
truncation of the 'efidebug dh' command.
As QEMU does not have special memory size restrictions remove the settings
from the defconfig files and go with the generic defaults.
Fixes: d0ee7f295d ("Convert CONFIG_SYS_PBSIZE to Kconfig")
Fixes: d31466b382 ("Convert CONFIG_SYS_CBSIZE to Kconfig")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable USB device and fastboot support which may be used to load the
Toradex Easy Installer FIT image.
While at it also enable USB mass storage aka UMS support.
Note that the i.MX 8M Plus recovery mode support is based on the USB
boot stage of the BOOTROM and does NOT require USB SDP SPL aka serial
downloader support.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
-----BEGIN PGP SIGNATURE-----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=gvDs
-----END PGP SIGNATURE-----
Merge tag 'tpm-next-27102023' of https://source.denx.de/u-boot/custodians/u-boot-tpm
bootX measurements and measurement API moved to u-boot core:
Up to now, U-Boot could perform measurements and EventLog creation as
described by the TCG spec when booting via EFI.
The EFI code was residing in lib/efi_loader/efi_tcg2.c and contained
both EFI specific code + the API needed to access the TPM, extend PCRs
and create an EventLog. The non-EFI part proved modular enough and
moving it around to the TPM subsystem was straightforward.
With that in place we can have a common API for measuring binaries
regardless of the boot command, EFI or boot(m|i|z), and contructing an
EventLog.
I've tested all of the EFI cases -- booting with an empty EventLog and
booting with a previous stage loader providing one and found no
regressions. Eddie tested the bootX part.
Eddie also fixed the sandbox TPM which couldn't be used for the EFI code
and it now supports all the required capabilities. This had a slight
sideeffect in our testing since the EFI subsystem initializes the TPM
early and 'tpm2 init' failed during some python tests. That code only
opens the device though, so we can replace it with 'tpm2 autostart'
which doesn't error out and still allows you to perfom the rest of the
tests but doesn't report an error if the device is already opened.
There's a few minor issues with this PR as well but since testing and
verifying the changes takes a considerable amount of time, I prefer
merging it now.
Heinrich has already sent a PR for -master containing "efi_loader: fix
EFI_ENTRY point on get_active_pcr_banks" and I am not sure if that will
cause any conflicts, but in any case they should be trivial to resolve.
Both the EFI and non-EFI code have a Kconfig for measuring the loaded
Device Tree. The reason this is optional is that we can't reason
when/if devices add random info like kaslr-seed, mac addresses etc in
the DT. In that case measurements are random, board specific and
eventually useless. The reason it was difficult to fix it prior to this
patchset is because the EFI subsystem and thus measurements was brought
up late and DT fixups might have already been applied. With this
patchset we can measure the DT really early in the future.
Heinrich also pointed out that the two Kconfigs for the DTB measurements
can be squashed in a single one and that the documentation only explains
the non-EFI case. I agree on both but as I said this is a sane working
version, so let's pull this first it's aleady big enough and painful to
test.
- Fix environment saving for new Android boot features on vim3*_android
- Add SPIFC support for Amlogic A1
- Add DFU RAM boot step when booting over USB
Use the sandbox TPM driver to measure some boot images in a unit
test case.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The environment is used to configure some additional boot features such as:
* extra boot arguments
* enable AVB (Android Verified Boot) verification
Right now, we cannot store it in eMMC:
Loading Environment from nowhere... OK
Fix it by enabling the appropriate options in the defconfig
Fixes: b749d5ecdc ("configs: meson64_android: define raw parts for bootloader")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231026-fix-saveenv-v1-1-6aa59be65481@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Extend Turris Mox board code to support CZ.NIC's RIPE Atlas Probe.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
SCMI power domain management protocol is supported on sandbox
for test purpose. Add fake agent interfaces and associated
power domain devices.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Current code allows up to 3 MBR partitions without extended one.
If more than 3 partitions are required, then extended partition(s)
must be used.
This commit allows up to 4 primary MBR partitions without the
need for extended partition.
Add mbr test unit. In order to run the test manually, mmc6.img file
of size 12 MiB or greater is required in the same directory as u-boot.
Test also runs automatically via ./test/py/test.py tool.
Running mbr test is only supported in sandbox mode.
Signed-off-by: Alex Gendin <agendin@matrox.com>
[ And due to some further changes for testing ]
Signed-off-by: Simon Glass <sjg@chromium.org>
- Add Board: rk3588 NanoPC-T6, Orange Pi 5, Orange Pi 5 Plus;
- clk driver fix for rk3568 and rk3588;
- rkmtd cmd support for rockchip nand device;
- dts update and sync from linux;
Enable rkmtd command for testing with sandbox_defconfig
and sandbox64_defconfig.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Xunlong Orange Pi 5 Plus is a single-board computer based on the
Rockchip RK3588 SoC. The board provides abundant interfaces, including
two HDMI output ports, one HDMI input port, two 2.5G Ethernet ports,
M.2 M-Key slot, M.2 E-Key slot, two USB 3.0, two USB 2.0, and two Type-C.
Features tested on a Orange Pi 5 Plus 4GB v1.2:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet
Device tree is imported from linux v6.7-rockchip-dts64-1 tag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Xunlong Orange Pi 5 is a single-board computer based on the Rockchip
RK3588S SoC. The board provides abundant interfaces, HDMI output, GPIO
interface, M.2 PCIe2.0, Type-C, Gigabit LAN port, 2*USB2.0, 1*USB3.0,
etc.
Features tested on a Orange Pi 5 4GB v1.2:
- SD-card boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet
Device tree is imported from linux v6.7-rockchip-dts64-1 tag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for rk3588 and rock-5b contain usb3 nodes that have
deviated too much from current state of submitted mainline linux usb3
patches, see [1].
Sync usb3 related nodes from latest patches and collaboras rk3588 tree
so that dwc3-generic driver can be updated to include support for the
rockchip,rk3588-dwc3 compatible in the future, use rockchip,rk3568-dwc3
compatible until final node is merged in linux maintainer tree.
[1] https://lore.kernel.org/lkml/20231009172129.43568-1-sebastian.reichel@collabora.com/
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable support for PCIe SATA cards and the on-board SATA controller.
This also revert use of CONFIG_PCI_INIT_R in order to speed up boot from
eMMC or SD-cards. Standard boot will initialize pci after faster boot
media have been enumerated.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Tested-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable Kconfig options for the two USB 2.0 ports and bottom USB 3.0 port
on ROCK 5 Model A.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmU2fxwcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyKr+B/42+WkPiAiwt79R6Kh5
UKo404oN1na28D3V12EvikiCH2QWubi38EV7VfcB3jqEpxj4j+rY0cSLZv+u7d4/
bfQN3FPrcTwYnXYLbYkUKC+MAVzGLiVzFBBhIt5cPrT4iVXctwYY6LJ58aX8uRo6
KU6CwXYc3cnmIUqpXE4EYbbQU4TAp55SV2n8QLFFI9DHcy2kELfdrZduFn+Hm9Ij
9sQHH5JxbrGHv5XpcjJkARW3M4K3K4TPzweFGN61VMJwWqzD3L4YPshwIGDfhRui
LECKCdr/rWkavumXCfw2pD3RYFTqnqnUzaEN/3ueL9FCJ2uFH1EyaoSuXFEn3+Ul
m1LE
=CMMd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2024.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2024.01 cycle
This feature set a new board named Conclusive KSTR sama5d27 with some
small prerequisites patches.
Introduce support for Conclusive KSTR-SAMA5D27 Single Board Computer.
Co-developed-by: Jakub Klama <jakub@conclusive.pl>
Signed-off-by: Jakub Klama <jakub@conclusive.pl>
Co-developed-by: Marcin Jabrzyk <marcin@conclusive.pl>
Signed-off-by: Marcin Jabrzyk <marcin@conclusive.pl>
Signed-off-by: Artur Rojek <artur@conclusive.pl>
The NanoPC-T6 is a Rockchip RK3588 based SBC by FriendlyElec.
There are four variants depending on the DRAM size: 4G/32GB eMMC,
8G/64GB eMMC, 16G/16MB SPI NOR, and 16G/256GB eMMC/16MB SPI NOR
Specifications:
CPU: Rockchip RK3588, 4x Cortex-A76 (up to 2.4GHz)
+ 4x Cortex-A55 (up to 1.8GHz)
GPU: Mali-G610 MP4
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder,
4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
RAM: 64-bit 4GB/8GB/16GB LPDDR4X at 2133MHz
eMMC: 0GB/32GB/64GB/256GB HS400
MicroSD Slot: MicroSD SDR104
PCIe 3.0: M.2 M-Key x1, PCIe 3.0 x4 for NVMe SSDs up to 2,500 MB/s
Ethernet: PCIe 2.5G 2x Ethernet (RTL8125BG)
PCIe 2.1: M.2 E-Key x1, PCIe 2.1 x1 and USB2.0 Host,
supports M.2 WiFi and Bluetooth
4G Module: MiniPCIe x1, MicroSIM Card Slot x1
Audio Out: 3.5mm jack for stereo headphone output
Audio In: 2.0mm PH-2A connector for analog microphone input
Video Input: standard HDMI input port, up to 4Kp60
2x 4-lane MIPI-CSI, compatible with MIPI V1.2
Video Output: 2x standard HDMI output ports compatible with HDMI2.1,
HDMI2.0, and HDMI1.4
2x 4-lane MIPI-DSI, compatible with MIPI DPHY 2.0 or CPHY 1.1
USB-A: USB 3.0, Type A
USB-C: Full function USB Type‑C port, DP display up to 4Kp60, USB 3.0
40-pin 2.54mm header connector: up to 2x SPIs, 6x UARTs, 1x I2Cs,
8x PWMs, 2x I2Ss, 28x GPIOs
Debug UART: 3 Pin 2.54mm header, 3V level, 1500000bps
Onboard IR receiver: 38KHz carrier frequency
RTC Battery: 2 Pin 1.27/1.25mm RTC battery connector for low power
RTC IC HYM8563TS
5V Fan connector
Working Temperature: 0C to 70C
Power: 5.5*2.1mm DC Jack, 12VDC input
Dimensions: 110x80x1.6mm (without case) / 86x114.5x30mm (with case)
Kernel commits:
893c17716d0c ("arm64: dts: rockchip: Add NanoPC T6")
a721e28dfad2 ("arm64: dts: rockchip: Add NanoPC T6 PCIe Ethernet support")
ac76b786cc37 ("arm64: dts: rockchip: Add NanoPC T6 PCIe e-key support")
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable mini PCIe slot, pcie3x1 node, now that the PCIe PHY driver
support bifurcation.
A pinctrl is assigned for reset-gpios or the device may freeze running
pci enum and nothing is connected to the mini PCIe slot.
Also drop the AHCI_PCI Kconfig option as this option is not required for
a functional M.2 SATA drive slot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The MangoPi MQ-R board uses an Allwinner T113s Soc (with 128MB of
embedded DRAM), support for which was just added to the code.
Since the devicetree was already synced from the latest Linux kernel
tree, all we need is a _defconfig file to add support for the board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The CONFIG_MACPWR Kconfig symbol is used to point to a GPIO that enables
the power for the Ethernet "MAC" (mostly PHY, really).
In the DT this is described with the phy-supply property in the MAC DT
node, pointing to a (GPIO controlled) regulator. Since we need Ethernet
only in U-Boot proper, and use a DM driver there, we should use the DT
instead of hardcoding this.
Add code to the sun8i_emac and sunxi_emac drivers to check the DT for
that regulator and enable it, at probe time. Then drop the current code
from board.c, which was doing that job before.
This allows us to remove the MACPWR Kconfig definition and the respective
values from the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
The CONFIG_SATAPWR Kconfig symbol was used to point to a GPIO that
enables the power for a SATA harddisk.
In the DT this is described with the target-supply property in the AHCI
DT node, pointing to a (GPIO controlled) regulator. Since we need SATA
only in U-Boot proper, and use a DM driver for AHCI there, we should use
the DT instead of hardcoding this.
Add code to the sunxi AHCI driver to check the DT for that regulator and
enable it, at probe time. Then drop the current code from board.c, which
was doing that job before.
This allows us to remove the SATAPWR Kconfig definition and the
respective values from the defconfigs.
We also select the generic fixed regulator driver, which handles those
GPIO controlled regulators.
Please note that the OrangePi Plus is a bit special here, it's a H3
board without native SATA, but with a USB-to-SATA bridge. The DT models
the SATA power via a VBUS supply regulator, which we don't parse yet in
the USB PHY driver. Use the hardcoded CONFIG_USB3_VBUS_PIN for that
board meanwhile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Enable building Pogo V4 u-boot image with LTO, which results in about 30K
reduction in size.
Rebased to latest master and resend.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Fork from ae350_rv[32/64]_spl_[xip]_defconfig and
append CONFIG_SPL_LOAD_FIT_OPENSBI_OS_BOOT=y
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The i.MX93 11x11 EVK fails to boot with following error:
Model: NXP i.MX93 11X11 EVK board
DRAM: 2 GiB
Error binding driver 'imx93-adc': -96
Some drivers failed to bind
Error binding driver 'simple_bus': -96
Some drivers failed to bind
Error binding driver 'simple_bus': -96
Some drivers failed to bind
initcall sequence 00000000fffb8f28 failed at call 000000008021e0d4 (err=-96)
### ERROR ### Please RESET the board ###
That's because since commit e7ff54d963 ("imx93_evk: defconfig: add adc
support") CONFIG_ADC_IMX93 is enabled but CONFIG_ADC is not.
Fix this by enabling CONFIG_ADC in imx93_11x11_evk_defconfig.
Make sure this situation won't happen again in future i.MX93 defconfig by
making CONFIG_ADC_IMX93 depend on CONFIG_ADC.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add test for the SPI load method. This one is pretty straightforward. We
can't enable FIT_EXTERNAL with LOAD_FIT_FULL because spl_spi_load_image
doesn't know the total image size and has to guess from fdt_totalsize. This
doesn't include external data, so loading it will fail.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test for the NOR load method. Since NOR is memory-mapped we can
substitute a buffer instead. The only major complication is testing LZMA
decompression. It's too complex to implement LZMA compression in a test, and we
have no in-tree compressor, so we just include some pre-compressed data. This
data was generated through something like
generate_data(plain, plain_size, "lzma")
cat plain.dat | lzma | hexdump -C
and was cleaned up further in my editor.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test for loading U-Boot over TFTP. As with other sandbox net
routines, we need to initialize our packets manually since things like
net_set_ether and net_set_udp_header always use "our" addresses. We use
BOOTP instead of DHCP, since DHCP has a tag/length-based format which is
harder to parse. Our TFTP implementation doesn't define as many constants
as I'd like, so I create some here. Note that the TFTP block size is
one-based, but offsets are zero-based.
In order to avoid address errors, we need to set up/define some additional
address information settings. dram_init_banksize would be a good candidate
for settig up bi_dram, but it gets called too late in board_init_r.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
