This code has compile problems and the company does not even exist any
more. So we take the liberty to drop support for it.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Wolfgang Denk <wd@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
Add support for the ARM part of the mgcoge2, named suen3.
This board is based on the Marvell Kirkwood (88F6281) SoC.
As there come more board variants, common config options
are collected in include/configs/km_arm.h. Also, this board
use common code for all keymile boards, which is stored in
board/keymile/common/common.c
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Heiko Schocher <hs@denx.de>
This is an i.MX25 base board with only NAND
so it uses nand_spl to boot.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Tune configuration, add support for (redundant) environment in NAND.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
The patch adds initial support for the Freescale mx51evk board.
Network (FEC) and SD controller (fsl_esdhc) are supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
* new board (eb_cpux9k2)
* support for EB+CPUx9K2 board by BuS Elektronik GmbH & Co. KG
* select via make eb_cpux9k2_config
* this also demonstrates, how to use boards with AT91RM9200 cpu
in at91 arch tree
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Added support for the following EDB93xx boards:
EDB9301
EDB9302
EDB9302A
EDB9307
EDB9307A
EDB93012
EDB9315
EDB9315A
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
This patch adds support for esd gmbh OTC570 board.
The OTC570 is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
The EXBITGEN board has not been maintained for a long time; it has
build problems, but no hardware is available any more for testing.
Drop support for this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
The new board revision has a different LCD.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The caddy2 is a variant of the already supported vme8349. So we just
add the differences to this board port. To better support those two
boards we switched from fixed SDRAM configuration to usage of
spd_sdram(). This is done by providing a board specific SPD EEPROM
routine with different values for both boards.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
changed to use mkconfig -t option instead, plus misc codingstyle fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for A320 evaluation board from Faraday. This board
uses FA526 processor by default and has 512kB and 32MB NOR flash, 64M RAM.
FA526 is an ARMv4 processor and uses the ARM920T source in this patch.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Integrate DA830 EVM support into U-Boot.
Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum
Digital EVM board. See http://www.spectrumdigital.com/
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
This patch adds support for the board IPEK01 based on the MPC5200.
The Futjitsu Lime graphics controller is configured in 16 bpp mode.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Start of support of
Texas Instruments Software Development Platform(SDP)
for OMAP3430 - SDP3430
Highlights of this platform are:
Flash Memory devices:
Sibley NOR, Micron 8bit NAND and OneNAND
Connectivity:
3 UARTs and expanded 4 UART ports + IrDA
Ethernet, USB
Other peripherals:
TWL5030 PMIC+Audio+Keypad
VGA display
Expansion ports:
Memory devices plugin boards (PISMO)
Connectivity board for GPS,WLAN etc.
Completely configurable boot sequence and device mapping
etc.
Support default jumpering and:
- UART1/ttyS0 console(legacy sdp3430 u-boot)
- UART3/ttyS2 console (matching other boards,
and SDP HW docs)
- Ethernet
- mmc0
- NOR boot
Currently the UART1 is enabled by default. for
compatibility with other OMAP3 u-boot platforms,
enable the #define of CONSOLE_J9.
Conflicts:
Makefile
Fixed the conflict with smdkc100_config by moving omap_sdp3430_config
to it is alphabetically sorted location above zoom1.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch adds the initial support for DM6467 EVM.
Other features like NET and NAND support will be added as follow up patches.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adds new board SMDKC100 that uses s5pc100 SoC
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
these boards are built around Atmel's AT91SAM9260/9G20 and have
up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND
and include a 10/100 Ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR
flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII
mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The CM-BF537U is similar to the CM-BF537E module, but enough to need its
own board port.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by
Calao Systems <http://www.calao-systems.com>. Their components are very
similar to the AT91SAM9260EK board, so their configuration is based on
the configuration of this board. There are however some differences:
different clocks, no LCD, no ethernet. They also can use SPI EEPROM to
store the environment.
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems
<http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC
running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard
battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND
flash, two USB host ports, and an USB device port. More informations can be
found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
This patch adds support for i.MX27-LITEKIT development board from
LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND
flash, FEC ethernet controller integrated into i.MX27.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.
Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the DEKA Research and Development galaxy5200 board
The galaxy5200 is an Freescale mpc5200 based embedded industrial
control board.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards. Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This is Marvell's 88F6281_A0 based reference design board
This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This is Marvell's 88F6281_A0 based custom board developed
for wireless access point product
This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash
5. Boot from USB supported
Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Reference:
http://plugcomputer.org/http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support
This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND
5. Enabled USB PHY init for kernel need
6. Boot from USB supported
Note: to boot Kirkwood kernel with USB support,
you should add "usb start" in the boot sequence
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
