Fix proper portsize: The register for portsize is either 00b, 01b,
or 1xb. The value that previous assigned is 32d.
Fix DRAM bring up: insert asm("nop") for every DRAM register setup
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Fix incorrect default environment for flash erase or protect
range. Change offset from 0 to 0xff80nnnn. Remove default
ethernet setup and MAC address.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Newer ColdFire processors family boot from address 0 instead of
0xFFnn_nnnn. When the boot flash base chip select is set at new
location instead of 0, an un-predictable error will occur if
there is an vector being trigger and refer it to an invalid
address or the vector table handler is not existed at address
0.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Provide parameter passing to uart_port_config(). Update port
configuration - un-mask it before enable the bits.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Use correct definition for _MASK and _UNMASK. It was combined in
the previous used and causes confusion.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
This fixes the following warnings when running MAKEALL for coldfire :
cmd_bdinfo.c:354: warning: 'print_eth' defined but not used
Signed-off-by: Philippe De Muyter <phdm at macqel.be>
Using seperate function calls for each bit-bang of slave serial
load can be painfully slow. This patch adds the possibility to
supply a block write function that loads the complete block of
data in one call (like it can already be done with Altera FPGAs).
On an MCF5373L (240 MHz) loading an XC3S4000 this reduces the load
time from around 15 seconds to around 3 seconds
Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
ep93xx timer: Make get_ticks() return a value in CONFIG_SYS_HZ resolution,
as announced by get_tbclk()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
ep93xx timer: Use 64-bit values in usecs_to_ticks() in order to avoid
overflows in intermediate values
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Allow overwriting defined partitions in the device tree blob
using partition info defined in the 'mtdparts' environment
variable.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Gerald Van Baren <vanbaren@cideas.com>
Match history buffer size to console buffer size. History buffer size
was hard coded to 256, artificially limiting the command buffer size.
The history buffer now tracks CONFIG_SYS_CBSIZE.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
When CONFIG_SYS_CBSIZE equals MAX_CMDBUF_SIZE, a command string of
maximum length will overwrite part of the history buffer, causing the
board to die. Expand the console_buffer and hist_lines buffer by one
character each to hold the missing NULL char.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Add POST progress API implemented as weak calls before and after
each call to the POST test callback in the post_run_single routine
of the post.c file.
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
This patch add functionality to use memory addresses in expressions.
This increases the power of expressions substantially
It adheres to the standard convemtions: memory addresses can be given
in the format *address (e.g. *1000)
Rationale for this change is that it allows masking off bits from a
byte that is obtained by reading data from e.g. i2c.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Fix warning: control reaches end of non-void function
Signed-off-by: Wolfgang Denk <wd@denx.de>
according to some of the comments the subaddress length is 1 or 2, but we are being
prepared for the case it becomes 3. However the code also accepted 4.
This repairs this by changing the constand 4 to 3.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
If a splashscreen is used the console scrolling used the
scroll size as needed when a logo was displayed. This
patch sets the scroll size to the whole screen if
a splashscreen is shown.
Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
The crc table was being built as little endian for big endian
targets. This would cause fw_printenv to always fail with
"Warning: Bad CRC, using default environment" messages.
Signed-off-by: Jeff Angielski <jeff@theptrgroup.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Fix warnings while compiling with CONFIG_VIDEO enabled:
diu.c: In function 'video_hw_init':
diu.c:158: warning: 'return' with no value, in function returning non-void
diu.c:162: warning: format '%ld' expects type 'long int', but argument 6 has type 'int'
diu.c:162: warning: format '%ld' expects type 'long int', but argument 7 has type 'int'
Signed-off-by: Anatolij Gustschin <agust@denx.de>
If a board uses cfb_console driver and splash image
and also defines CONFIG_SILENT_CONSOLE, the user is
locked out even if "silent" is not set. It is not
possible to get any output, neither on vga console
device nor on serial console after redirecting the
output to the serial console, since the GD_FLG_SILENT
flag remains set.
Fix the problem by redirecting the output from frame
buffer to serial console if splashimage is used.
Only suppress the output if "silent" environment
variable was set and don't set the GD_FLG_SILENT
flag arbitrarily.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'
Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Some registers of the mxcmmc driver were accessed using
16 bit accessor functions, because only the LSB is
significant. This is not needed and generates
warnings.
Signed-off-by: Stefano Babic <sbabic@denx.de>
So far, TFTP negotiated a fixed retransmission timeout of 5 seconds.
In some cases (busy networks, slow TFTP servers) this caused very
slow transfers. A new environment variable "tftptimeout" allows to
set this timeout. Lowering this value may make downloads succeed
faster in networks with high packet loss rates or with unreliable
TFTP servers.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch removes the \n after the help message for mmcinfo.
This resulted in an empty line being displayed after the mmcinfo line
when the help command was given.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
The new zlib code wants asm/unaligned.h, so have the Blackfin version pull
in the asm-generic/unaligned.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is based on the asm-arm/unaligned.h, but made generic so all arches
that cannot do unaligned accesses can utilize it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If a splashscreen is used the console scrolling used the
scroll size as needed when a logo was displayed. This
patch sets the scroll size to the whole screen if
a splashscreen is shown.
Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
Building examples/standalone/eepro100_eeprom triggers this error:
In file included from include/common.h:629,
from eepro100_eeprom.c:24:
include/net.h: In function 'NetReadIP':
include/net.h:430: warning: implicit declaration of function 'memcpy'
eepro100_eeprom.c: At top level:
eepro100_eeprom.c:81: error: conflicting types for 'memcpy'
include/net.h:430: error: previous implicit declaration of 'memcpy' was here
Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This code has compile problems and the company does not even exist any
more. So we take the liberty to drop support for it.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Wolfgang Denk <wd@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
The 36-bit build exceeds the 512k size we have. Removing FIT type image
support allows us to fit and we dont really use it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
