As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1028a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1028a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable related configs on all lx2160ardb boards to support pcf2127
rtc DM feature.
Also remove SYS_I2C_MXC_I2Cx, where x is from 1 to 8 from
Kconfig.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 in dts for
lx2160aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Lx2160ardb need to use i2c0 before relocation, so we also need to set
u-boot, dm-pre-reloc to initialize node before relocation.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Adds the pcf2127-rtc node under the i2c4 node dts of lx2160ardb boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
In lx2160a soc, there are eight i2c controllers, this patch adds i2c
nodes for lx2160a, and the gpio2 nodes on which the i2c4 controller
depends.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls2160a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
I2C dm mode enablemenet causes below compilation errors:
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f':
board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration
of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'?
[-Wimplicit-function-declaration]
i2c_early_init_f();
^~~~~~~~~~~~~~~~
arch_early_init_r
drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe':
drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function
'enable_i2c_clk';
did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration]
ret = enable_i2c_clk(1, bus->seq);
^~~~~~~~~~~~~~
enable_irq_wake
So fix these compilation errors.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch solves
the problem that the i2c-related api of the lx2160a platform does not
support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Move CONFIG_FSL_QSPI from header file to defconfigs,
consequently unset imply config(CONFIG_SPI_FLASH_BAR) which
is not valid for LS series.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Select BOARD_LATE_INIT for ls1028ardb and ls1028aqds targets
so that late init work can be done.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This driver needs modification to work with new soc,
like ls1028, since bitmap of RCFG is changed to
RESV[7:5] LIVE[4] WDEN[3] RESV[2:1] GO[0]
000 1 0 00 0
Also the RCW location is moved to only dutcfg0.
RESV[7:4] RCWSRC[3:0]
1111 configurable
Following commands are functional now
qixis_reset
qixis_reset sd
qixis_reset qspi
qixis_reset emmc
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
MC firmware need to be aligned to 512M, so minimum 512MB DDR is reserved.
But MC support to work with 128MB or 256MB DDR memory also, in this
case, rest of the memory is not usable.
So reporting this extra memory to Linux through dtb memory fixup.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Since we added clk enable_count and prograte clk child enabling
operation to clk parent, so add a new function sandbox_clk_enable_count
to get enable_count for test usage.
And add test code to get the enable_count after we enable/disable
the device clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX8MM, thinking such as clk path
OSC->PLL->PLL GATE->CCM ROOT->CCGR GATE->Device
Only enabling CCGR GATE is not enough, we also need to enable PLL GATE
to make sure the clk path work. So when enabling CCGR GATE,
we could prograte to enabling PLL GATE to make life easier.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As what Linux Kernel 5.3.0 provides when enable/disable clk,
there is an enable_count in clk_core_disable/enable. Introduce
enable_count to track the clk enable/disable count when
clk_enable/disable for CCF. And Initialize enable_count to 0 when
register the clk.
And clk tree dump with enable_count will be supported, it will
be easy for us to check the clk status with enable_count
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Based on discussion with Stephen Warren there was recommendation to list
both memory and random command dependencies just in case that dependency is
not properly handled by Kconfig.
Fixes: a09c1f7e1c ("test/py: Fix MMC/SD block write test dependency")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Building easylogo with `HOST_TOOLS_ALL=y make tools` results in a build
warning due to a possible buffer overrun:
tools/easylogo/easylogo.c:453:4: note: ‘sprintf’ output between 7 and
262 bytes into a destination of size 256
sprintf (str, "%s, 0x%02x", app, *dataptr++);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Truncate the output to fit into the destination buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Looking at the contents of file .mailmap it seems that some editors assumed
that translation is done by entering multiple lines into the file and the
last one replaces the others. This is not how it works. The translation
occurs according to entries in single lines as described in the
git-check-mailmap man-page.
Add a description of the file format.
Add an entry for Alexander Graf as his old email address is not valid
anymore.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The earlier commit....
commit a5a5d997b4 ("spl: Allow performing BSS init early before board_init_f()")
...introduced the ability to use BSS from SPL's board_init_f() as it may
be required in certain exceptional use cases so go ahead and update the
README to reflect this change. Note that as highlighted with the changes
the use of the associated CONFIG option is generally not recommended.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Based on discussion with Stephen Warren there was recommendation to list
both memory and random command dependencies just in case that dependency is
not properly handled by Kconfig.
Fixes: a09c1f7e1c ("test/py: Fix MMC/SD block write test dependency")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Building easylogo with `HOST_TOOLS_ALL=y make tools` results in a build
warning due to a possible buffer overrun:
tools/easylogo/easylogo.c:453:4: note: ‘sprintf’ output between 7 and
262 bytes into a destination of size 256
sprintf (str, "%s, 0x%02x", app, *dataptr++);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Truncate the output to fit into the destination buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Looking at the contents of file .mailmap it seems that some editors assumed
that translation is done by entering multiple lines into the file and the
last one replaces the others. This is not how it works. The translation
occurs according to entries in single lines as described in the
git-check-mailmap man-page.
Add a description of the file format.
Add an entry for Alexander Graf as his old email address is not valid
anymore.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The earlier commit....
commit a5a5d997b4 ("spl: Allow performing BSS init early before board_init_f()")
...introduced the ability to use BSS from SPL's board_init_f() as it may
be required in certain exceptional use cases so go ahead and update the
README to reflect this change. Note that as highlighted with the changes
the use of the associated CONFIG option is generally not recommended.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
With DM_MMC enabled, enable CONFIG_BLK to remove this
compile warning for am43xx based targets:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Targets were compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
TI HS platforms generate *dtb_HS binary blobs and there is no
rule for cleanup. Added entry for cleanup in clean-files target.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The commit 1b42ab3eda ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock
frequencies based on OPP") updates the kernel device-tree blob to adjust
the DSP, IVA and GPU DPLL clocks based on a one-time OPP choice selected
in U-Boot. All these DPLL clocks are children of the cm_core_aon clocks
DT node.
The hierarchy of this clocks DT node has changed in newer Linux kernels
starting from v5.0, and this results in a failure in ft_fixup_clocks()
function to update the clock rates on these newer kernels. Fix this by
updating the lookup logic to look through both the newer and older
DT hierarchy paths for the cm_core_aon clocks node.
Signed-off-by: Suman Anna <s-anna@ti.com>
The Kconfig file calls to ti/common/Kconfig twice which makes
several of the menu items repeat themselves. In an effort to
clean this up, this patch removes the second call which eliminates
the duplicate menu items.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that SPL supports DM_SERIAL and the direct NOR boot supports
DM_SERIAL, the check to see if DM_SERIAL is defined can go away,
because all da850evm variants now support DM_SERIAL. This patch
simply removes some dead precompiler defines.
Signed-off-by: Adam Ford <aford173@gmail.com>
With SPL now supporting DM_SPI, the need for compiler directives
and hard-coded addresses is obsolete. This patch removes some
dead legacy code defining the SPI base address
Signed-off-by: Adam Ford <aford173@gmail.com>
Sorry for the noise, but there appears to be a regression with older
hardware. Since it broke the direct_nor boot option, it should be
reverted until a better solution is available.
This reverts commit 51cd1e2373.
Like we did with 'fit_loadaddr' to 'addr_fit', the variable
'fit_bootfile' contains a name and so should be prefixed with
name_. Make this change here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This is the first part of a larger effort I would like to propose to
unify and simplify the default set of environment variables.
When many early environment variables were named there were fewer images
being loaded, usually just a kernel. At this time names like 'loadaddr'
would suffice. Now we have more images and many more commands that act on
them, often re-using the same variable for several different uses. The
contents of a variable are also not immediately known causing one to have
to look up a chain of variables to understand what a command is actually
doing. I suggest the following.
To start, all variables containing names should be prefixed with name_
and addresses with addr_. This is like how K2 already does things and
allows for simple universal commands like:
get_fdt_nfs=nfs ${addr_fdt} /boot/${name_fdt}
Which is very clear on what is intended here and would work across all
board that using the this naming convention.
We can do this one variable at a time, start here with addr_fit.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
The variable 'name_overlays' serves the same purpose. Remove
'overlay_files' and use 'name_overlays' everywhere.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The full path has changed in the recent kernels so that it is
not possible to load them. Aliases "ethernet0" and "ethernet1"
are still present in both legacy and new kernels.
Also, fix error messages to correspond to the taken actions.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
