Snapdragon SoCs and IPQ40xx use common TLMM IP,
so existing driver supports IPQ40xx as well.
So lets simply add a compatible for IPQ40xx.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
IPQ40xx and currently supported Snapdragon boards don't use the same one
so enable reading it from DT, if no DT property is found default value
is the same as the previous define.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
This introduces initial support for the popular Qualcomm
IPQ40x8 and IPQ40x9 WiSoC series.
IPQ40xx series have 4x Cortex A7 ARM-v7A cores.
Supported are: IPQ4018, IPQ4019, IPQ4028 and IPQ4029.
IPQ40x8 and IPQ40x9 use the same cores, but differ in
addressable RAM size (1GB for IPQ40x9 and 256MB for IPQ40x8)
and supported peripherals (IPQ40x8 lacks RGMII, LCD controller
and EMMC/SDHCI controllers).
IQP4028/IPQ4029 models differ from IPQ4018/IPQ4019 only
by their rated temperatures rates with IPQ402X models being
rated for wider temperature ranges.
Initially this supports:
* Simple clock driver (Only for UART1 now, will be extended)
* Pinctrl driver (Supports UARTX and GPIO now, will be extended)
* GPIOs already supported by msm_gpio driver with updates
* UARTs already supported by serial_msm driver with updates
Further peripherals will come in later patches.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The pins for the MMC controller weren't being set up correctly because the
pinctrl driver only sets the GPIO pullup/pulldown config and doesn't
handle the special cases with PUPD/R0/R1 control.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
The sgmii mode init flow is almost the same for all mediatek SoC, the
only difference is the register offset(SGMSYS_GEN2_SPEED) is 0x2028
in the old chip(mt7622) but changed to 0x128 for the newer chip(mt7629
and the following chips).
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Done with:
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS -H
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: A few more migrations]
Signed-off-by: Tom Rini <trini@konsulko.com>
BOOTP_DEFAULT is defined in several boards, but this config
option is never checked or used.
This patch removes this config option from config files and
the whitelist.txt
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_DRIVERS
CONFIG_SPL_NAND_ECC
CONFIG_SPL_NAND_SIMPLE
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Recent CI failures were seen [1] when building MSYS2 Windows host
tools. The error messages are something like:
downloading mingw32.db...
downloading mingw32.db.sig...
error: mingw32: key "4A6129F4E4B84AE46ED7F635628F528CF3053E04" is unknown
error: mingw32: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust
error: failed to update mingw32 (invalid or corrupted database (PGP signature))
Per the MSYS2 official news [2], this was caused by a packager
switch and several solutions were suggested, e.g.: a new package
of msys2-keyring and a new msys2 installer that includes them are
released. However right now we have been using the MSYS2 github
CI base repo [3] for the MSYS2 build in U-Boot, but per the project
information on the github webpage, it says: "This repository is
unused/deprecated and will be remove after 2021-01-01". Since it is
unmaintained it's unlikely the new PGP keys will be included in the
git repo, and the only choice is to switch to use the MSYS2 official
installer as the CI base instead.
[1] https://dev.azure.com/u-boot/u-boot/_build/results?buildId=975
[2] https://www.msys2.org/news/#2020-06-29-new-packagers
[3] https://github.com/msys2/msys2-ci-base
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Package 'flex' is needed when building the U-Boot host tool, but
is currently missing in the build dependency in the CI pipeline.
This is to prepare switching to an installer based CI build.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This simplifies things a bit to just use a login shell everywhere.
This keeps in sync with MSYS2 upstream commit:
9d11b7f0aa93 ("azure-pipelines: simplify things a bit").
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
With the migration to python3 for all of our tests, we need to install
pyelftools via pip now rather than the system tools as they will
otherwise not be present in our virtualenv.
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Changes in v2: Switch to pip
This checks and handles RX errors on the Amlogic UART controller
after experiencing errors on the Khadas VIM3 & VIM3L when UART AO A
lines are not connected.
When the RX line is not connected, the first byte is erroneous and breaks
the U-Boot autoboot, breaking automatic boot.
This checks and drops any erroneous RX byte on pending and getc callbacks
to avoid returning true to pending when an error byte is in the FIFO.
Fixes: bfcef28ae4 ("arm: add initial support for Amlogic Meson and ODROID-C2")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
- Assorted environment fixes.
- Enhance environment in MMC and controlled via OF_CONTROL
- Allow for environment in FAT to use the same device we boot from
rather than be hard-coded.
Restore CONFIG_ENV_ADDR value to fix boot hang with IFC-NOR
which is default boot source.
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
According to Server Base System Architecture (SBSA) specification,
the SBSA Generic Watchdog has two stage timeouts: the first signal
(WS0) is for alerting the system by interrupt, the second one (WS1) is a
real hardware reset.
More details about the hardware specification of this device:
ARM DEN0029B - Server Base System Architecture (SBSA)
This driver can operate ARM SBSA Generic Watchdog as a single stage
In the single stage mode, when the timeout is reached, your system
will be reset by WS1. The first signal (WS0) is ignored.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the PCIe EP mode support for lx2160a-v2 platform.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Modify the ls_pcie_dump_atu function, make it can print the INBOUND
windows registers.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the INBOUND configuration for VFs of PF.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Due to the ls2085a and ls2080a use different way to set the BAR size,
so add the BAR size init code here.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The VF_BARn_REG register's Prefetchable and Type bit fields
are overwritten by a write to VF's BAR Mask register.
workaround: Before writing to the VF_BARn_MASK_REG register,
write 0b to the PCIE_MISC_CONTROL_1_OFF register.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the multiple function support for Layerscape platform, some PEXs
of Layerscaple platform have more than one PF.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the PCIe EP node for ls1046a.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Some EP deivces need to initialize before RC scan it, e.g. NXP
layerscape platform, so add the init function in pci_ep uclass.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Split the RC and EP driver, and reimplement the EP driver base on
the EP framework.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev2 requires 4KB space for type0 and 4KB
space for type1 iATU window. Increase configuration
size to 8KB to have sufficient space for type0
and type1 window.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Drop ifdef CONFIG_SYS_I2C to initialize
baudrate of i2c
- Drop warning of i2c_early_init_f as follows,
warning: implicit declaration of function 'i2c_early_init_f'; did you
mean 'arch_early_init_r'? [-Wimplicit-function-declaration]
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
