Loading part of TF-A into SRAM from eMMC using DMA fails on RK3399
similar to other Rockchip SoCs. Checksum validation fails with:
## Checking hash(es) for Image atf-2 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-2' image node
spl_load_simple_fit: can't load image loadables index 1 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Add a device tree property, u-boot,spl-fifo-mode, to control when the
rockchip_sdhci driver should disable the use of DMA and fallback on PIO
mode. Same device tree property is used by the rockchip_dw_mmc driver.
In commit 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") the DMA mode was disabled using a CONFIG
option on RK3588. Revert that and instead disable DMA using the device
tree property for all RK3588 boards, also apply similar workaround for
all RK3399 boards.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
The workaround to limit number of blocks to read in a single command
should only be applied to RK3568 and RK3588. Change to be more strict
when to apply the workaround.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
Using DMA to load TF-A into SRAM fails when booting from eMMC on RK3588.
## Checking hash(es) for Image atf-3 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-3' image node
spl_load_simple_fit: can't load image loadables index 2 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
Fix this by using PIO mode in SPL and limit the number of blocks used in
a single read command to avoid triggering Data End Bit Error interrupt.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for RK3588 to the rockchip sdhci driver.
Use driver data to handle differences between RK3568 and RK3588:
- Set "Receive original clock source is auto gating" for RK3588.
- Set "Receive clock source is no-inverted" only on RK3568 and "Transmit
clock source is invertion of original clock input" for RK3588.
- Use different txclk_tapnum for HS400 modes on RK3588.
- Configure the CMDOUT reg for HS400 modes for RK3588.
This is based on the mainline linux and vendor kernel driver and have
successfully been tested with rock5b-rk3588_defconfig and
CONFIG_MMC_HS200_SUPPORT=y
CONFIG_MMC_HS400_SUPPORT=y
CONFIG_MMC_HS400_ES_SUPPORT=y
CONFIG_MMC_SPEED_MODE_SET=y
using the following command to switch mode and then read 512 MiB of data
from eMMC into memory,
=> mmc dev 0 0 <mode> && mmc info && mmc read 10000000 2000 10000
for each of the modes below.
0 = MMC legacy
1 = MMC High Speed (26MHz)
3 = MMC High Speed (52MHz)
4 = MMC DDR52 (52MHz)
10 = HS200 (200MHz)
11 = HS400 (200MHz)
12 = HS400ES (200MHz)
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Adjust tap number for transmit clock, tap number and delay number for
strobe input to fix HS400 modes on RK3568.
New values have been picked from vendor kernel and u-boot and have
successfully been tested with rock-3a-rk3568_defconfig and
CONFIG_MMC_HS200_SUPPORT=y
CONFIG_MMC_HS400_SUPPORT=y
CONFIG_MMC_HS400_ES_SUPPORT=y
CONFIG_MMC_SPEED_MODE_SET=y
using the following command to switch mode and then read 512 MiB of data
from eMMC into memory,
=> mmc dev 0 0 <mode> && mmc info && mmc read 10000000 2000 10000
for each of the modes below.
0 = MMC legacy
1 = MMC High Speed (26MHz)
3 = MMC High Speed (52MHz)
4 = MMC DDR52 (52MHz)
10 = HS200 (200MHz)
11 = HS400 (200MHz)
12 = HS400ES (200MHz)
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This rearrange and remove duplicate defines to make the code cleaner.
There is no need to read vendor area1 and use an offset each time, it is
easier and clearer to just use the reg offset defined in TRM, same as
the other vendor regs.
This also removes use of the misspelled const for the RK3588 CMDOUT reg,
it will be re-added when support for RK3588 is introduced.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove empty implementations of get_phy and set_enhanced_strobe ops.
Change driver set_enhanced_strobe to return 0 in order to allow missing
implementation of the ops.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor set_ios_post ops to correctly set UHS Speed Select field values
according to TRM. Also set or unset Enhanced Strobe Enable bit and
eMMC Card present bit in set_ios_post, the Enhanced Strobe Enable bit
was never unset after switching to HS400ES mode.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Check return value from mmc_send_cmd and clear HOST_CONTROL2 when there
is an error. Also skip enable of interrupt signaling and remove a delay,
a delay is already happening in sdhci_send_command.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to configure clock and DLL in set_clock and config_dll ops
instead of in the set_ios_post ops.
With this change the output clock is turned off while configuring DLL
parameters, according to the design recommendations.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the set_clock and config_dll sdhci_ops. Use of these ops
will allow configuration of DLL while the output clock is disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove the unneeded emmc_phy_init now that the no-inverter flag is
handled correctly after commit 2321a991bb ("rockchip: sdhci: rk3568:
bypass DLL when clk <= 52 MHz").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device private data is misused in rockchip_sdhci_of_to_plat and
rockchip_sdhci_execute_tuning.
In these functions dev_get_priv is assigned to struct sdhci_host:
struct sdhci_host *host = dev_get_priv(dev);
Instead, the sdhci host should refer to host in struct rockchip_sdhc:
struct rockchip_sdhc *priv = dev_get_priv(dev);
struct sdhci_host *host = &priv->host;
Because host is the first member in struct rockchip_sdhc this is not a
real problem, lets fix it anyway and also use priv name consistently.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
mmc->tran_speed is max clock, but currently rk3568_sdhci_set_ios_post
uses it if its != 0, regardless of mmc->clock value, and it breaks
eMMC controller.
Without this patch 'mmc dev 0; mmc dev 1; mmc dev 0' is enough for
breaking eMMC, since first initialization sets mmc->mmc_tran speed
to non-zero value (26MHz in my case), and on subsequent re-init when
mmc layer asks for 400KHz it sets 26MHz instead.
Fix it by using MAX(mmc->tran_speed, mmc->clock)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For Rockchip platform, DLL bypass bit and start bit need to be set if
DLL is not locked.
With this change applied eMMC in my NanoPi R5S can run at 52 MHz.
Based on linux commit b75a52b0dda3 ("mmc: sdhci-of-dwcmshc: Update DLL
and pre-change delay for rockchip platform")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A pointer can not be negative. Use macro IS_ERR_OR_NULL() for checking.
Signed-off-by: Haolin Li <li.haolin@qq.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This macro currently supports only one parameter. Based on Linux iopoll,
let's extend read_poll_timeout common API to allow multiple variable
parameters.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
On RK3568, a register bit must be set to enable Enhanced Strobe.
However, it appears that the address of this register may differ from
vendor to vendor and should be read from the underlying MMC IP. Let the
Rockchip SDHCI driver read this address and set the relevant bit when
Enhanced Strobe configuration is requested.
The IP uses a custom mode select value (0x7) for HS400, use that instead
of the common but non-standard SDHCI_CTRL_HS400 value (0x5). Also add
some necessary DLL_STRBIN and DLL_TXCLK configuration for HS400.
Additionally, a bit signifying that the connected hardware is an eMMC
chip must be set to enable Data Strobe for HS400 and HS400ES modes. Also
make the driver set this bit as appropriate.
This is partly ported from Linux's Synopsys DWC MSHC driver which
happens to be the underlying IP. (drivers/mmc/host/sdhci-of-dwcmshc.c in
Linux tree).
Co-developed-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On RK3399, a register bit must be set to enable Enhanced Strobe.
Let the Rockchip SDHCI driver set it when Enhanced Strobe configuration
is requested. However, having it set makes the lower-speed modes stop
working and makes reinitialization fail, so let it be unset as needed in
set_control_reg().
This is mostly ported from Linux's Arasan SDHCI driver which happens
to be the underlying IP. (drivers/mmc/host/sdhci-of-arasan.c in Linux
tree).
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip RK3399 eMMC PHY has to be power-cycled while changing its
clock speed to some higher speeds. This is dependent on the desired
SDHCI clock speed, and it looks like the PHY should be powered off while
setting the SDHCI clock in these cases.
Commit ac804143cf ("mmc: rockchip_sdhci: add phy and clock config for
rk3399") attempts to do this in the set_ios_post() hook by setting the
SDHCI clock once more while the PHY is turned off/on as necessary, as
the SDHCI framework does not provide a way to override how it sets its
clock. However, the commit breaks reinitializing the eMMC on a few
boards including chromebook_kevin and reportedly ROCKPro64.
This patch reworks the power cycling to utilize the SDHCI framework
slightly better (using the set_control_reg() hook to power off the PHY
and set_ios_post() hook to power it back on) which happens to fix the
issue, at least on a chromebook_kevin.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The default configuration of rk3399 EMMC PHY does not enable the
strobe line, and EMMC controller will got data transmission error
at HS400 mode.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support for the RK3568 platform to this driver.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock, phy and other configuration, it is convenient to support
new controller. Here a short summary of the changes:
- Add mmc_of_parse to parse dts config.
- Remove OF_PLATDATA related code.
- Reorder header inclusion.
- Add phy ops.
- add ops set_ios_post to modify the parameters of phy when the
clock changes.
- Add execute tuning api for hs200 tuning.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
In the current implementation, when dtoc parses a dtb to generate a struct
platdata it converts the information related to linked nodes as pointers
to struct platdata of destination nodes. By doing this, it makes
difficult to get pointer to udevices created based on these
information.
This patch extends dtoc to use struct driver_info when populating
information about linked nodes, which makes it easier to later get
the devices created. In this context, reimplement functions like
clk_get_by_index_platdata() which made use of the previous approach.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This patch fix mmc driver abort caused by below patch:
3d296365e4 mmc: sdhci: Add support for sdhci-caps-mask
After the patch sdhci_setup_cfg() access to host->mmc->dev,
so we have to do init before make the call to the function()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The Rockchip-specific SDHCI wrapper does not process the 'bus-width'
property in the SDHCI node. Consequently, the bus is always kept in
4bit mode, even if 8bit wide operation is available, supported and
requested in the DTS.
This change adds processing of the 'bus-width' property and sets the
host capability flag for an 8bit wide bus, if set to 8. As the logic
in sdhci.c does not support clearing the 4bit capability, we assume
that 4bit operation is always supported.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update the Rockchip SDHCI wrapper to support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in rockchip_sdhci.c
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the dw_mmc and sdhci wrapper drivers for Rockchip.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Change some API in order to enable of-platdata.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
The sdhci controller assumes that the base clock frequency is fully supported by
the peripheral and doesn't support hardware limitations. The Linux kernel
distinguishes between base clock (max_clk) of the host controller and maximum
frequency (f_max) of the card interface. Use the same differentiation and allow
the platform to constrain the peripheral interface.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Init the clock rate to max-frequency from dts with clock driver api.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
These functions can be much simpler by squashing lines for immediate
return.
For *_bind() callbacks, they will be a simple wrapper function of an
upper-level bind API.
For mmc_set_{boot_bus_width,part_conf}, they will be a wrapper of
mmc_switch().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Some arguments don't need to pass to sdhci_setup_cfg.
Generic variable can be used in sdhci_setup_cfg, and some arguments are
already included in sdhci_host struct.
It's enough that just pass the board specific things to sdhci_setup_cfg().
After removing the unnecessary arguments, it's more simpler than before.
It doesn't consider "Version" and "Capabilities" anymore in each SoC
driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rockchip rk3399 using arasan sdhci-5.1 controller.
This patch add the controller support to enable mmc device
with full driver-model support, tested on rk3399 evb board.
According to my test result, this driver should be OK,
the command "part list mmc 0" can result in a right output,
but all the mmc command failed like this:
=> mmc info
No MMC device available
Command failed, result=1
The result of get_mmc_num in cmd/mmc.c is always 0?
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
