Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms
that had been enabling it turn it on by hand. This exposed that we had
not yet migrated CMD_MTDPARTS fully, so do so now.
Fixes: 86dfa556d9 ("cmd: ubi: Remove useless call to mtdparts_init()")
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that CONFIG_SYS_MONITOR_LEN increased, we have room for enabling
more options again.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable "mtdparts" and "ubi" commands for uniphier_v8_defconfig to
use UBI on NAND devices.
Enable only "mtdparts" for uniphier_{v7,ld4_sld8}_defconfig because
enabling UBI would increase 170KB, which would be memory footprint
problem.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the on-chip ethernet driver for uniphier_{v7,v8}_defconfig.
Disable the on-board SMC911x because it has not migrated to the
driver model yet - it is not possible to enable DM and non-DM
drivers at the same time.
The CONFIG_SMC911X for uniphier_ld4_sld8_defconfig is still kept
because the on-chip ethernet driver for LD4, sLD8 is not supported
yet.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
cmd/Makefile has:
ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif
which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant
# CONFIG_CMD_FPGA is not set
can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
I thought commit d37d31849c ("ARM: uniphier: enable DWC3 xHCI
driver") enabled CONFIG_USB_DWC3_UNIPHIER, but CONFIG_USB_XHCI_DWC3
was missing in uniphier_v7_defconfig. Re-add.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
CONFIG_SMC911X
CONFIG_SMC911X_BASE
CONFIG_SMC911X_16_BIT
CONFIG_SMC911X_32_BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The main difference between Pro4 and PXs2/LD6b is the Denali NAND
IP version. This is now distinguished by DT. Merge the two defconfig
files into uniphier_v7_defconfig.
Update the README.uniphier too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-18 20:26:06 +09:00
Renamed from configs/uniphier_pxs2_ld6b_defconfig (Browse further)
