Commit graph

42 commits

Author SHA1 Message Date
Albert ARIBAUD
4b19b7448e Merge remote-tracking branch 'u-boot-imx/master'
The single file conflict below is actually trivial.

Conflicts:
	board/boundary/nitrogen6x/nitrogen6x.c
2014-10-08 21:20:49 +02:00
Eric Nelson
ce9507b793 nitrogen6x: display use I2C detect for HDMI
The HPD pin and RX_SENSE registers have proven to be less reliable
than using I2C on the EDID pins for detection of an HDMI monitor.
In particular, when the HDMI output is reset through a "reboot"
cycle, the detect_hdmi() routine often bounces, resulting in
a failure to detect a connected monitor.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:22 +02:00
Eric Nelson
c745de7174 nitrogen6x: display: add wvga-lvds panel
Add support for WVGA (800x480) panels using VESA GTF timings over
LVDS.

No auto-detection is supported, so you must configure this panel
manually through the 'panel' environment variable:

        U-Boot > setenv panel svga
        U-Boot > saveenv && reset

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:22 +02:00
Eric Nelson
865aa30bb3 nitrogen6x: display: add Ampire 1024x600 panel
Add support for an Ampire 1024x600 LVDS panel with integrated Ilitek
capacitive touch screen.

Auto-detection is enabled, so no explicit configuration is needed.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:22 +02:00
Eric Nelson
135663061f nitrogen6x: display: add svga display (800x600)
Add support for 800x600 18-bit RGB displays using VESA GTF timings.

No auto-detection is supported, so you must configure this panel
manually through the 'panel' environment variable:

        U-Boot > setenv panel svga
        U-Boot > saveenv && reset

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:22 +02:00
Eric Nelson
04edda266d nitrogen6x: display: add support for fusion 7 display
Add support for the Touch Revolution Fusion7 display: 800x480 RGB
with a custom F0710A resistive touch controller.

Auto-detection of this panel is supported so no configuration is
required.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:22 +02:00
Eric Nelson
d6949e3f9d nitrogen6x: display: add LDB-WXGA-S for SPWG 1280x800 displays
This patch adds support for LVDS WXGA displays that use the SPWG encoding
standard instead of JEIDA.

No auto-detection is enabled and you must explicitly set the 'panel'
environment variable:

        U-Boot > setenv panel LDB-WXGA-S
        U-Boot > saveenv && reset

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:22 +02:00
Eric Nelson
4adc1127f8 nitrogen6x: display: add support for LG-9.7 LVDS display
Add support for LG 9.7" LVDS panel (1024x768) with integrated eGalax
touch screen.

Note that this panel differs only slightly from the Hannstar XGA panel
(margins).

No auto-detection is available because it shares the same touch controller
as the Hannstar-XGA display, so you'll need to configure it through the
'panel' environment variable:

        U-Boot > setenv panel LG-9.7
        U-Boot > saveenv && reset

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:21 +02:00
Eric Nelson
443d4d15d7 nitrogen6x: display: add qvga panel
Add support for a 1/4 VGA panel with a 24-bit RGB interface.
No auto-detection is enabled, so you must configure the 'panel'
environment variable to use this display:

        U-Boot > setenv panel qvga
        U-Boot > saveenv && reset

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:21 +02:00
Robert Winkler
4328fb05bf nitrogen6x: display: add support lvds jeida screen
Add support for Boundary Devices 7" and 10.1" 1280x800 displays with
integrated FocalTech ft5x06 10-point touch controller.

Because they share the touch controller with the 1024x600 displays,
auto-detection is disabled and you must explicitly set the 'panel'
environment variable:

        U-Boot > setenv panel LDB-WXGA
        U-Boot > saveenv && reset

Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:21 +02:00
Eric Nelson
84caf0b26b nitrogen6x: prevent warnings about board_ehci* callbacks
Include declarations of board_ehci callbacks to prevent compiler warnings
and enforce function prototypes.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:21 +02:00
Troy Kisky
adc4a2bd03 nitrogen6x: phy: add 100 us delay after phy reset
Testing shows that the Micrel PHY may not be completely out
of reset if accessed immediately.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:21 +02:00
Eric Nelson
9fc425278b nitrogen6x: staticize board file
Declare locally-used data structures and functions as
static and pull in header files to prevent compiler warnings
of "Should it be static?" when building with "make C=1".

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:21 +02:00
Troy Kisky
693cccf412 nitrogen6x: configure SGTL5000, CSI camera clock outputs
Configure CLKO outputs for SGTL5000, CSI camera.

The sys_mclk output for the SGTL500 in particular prevents
Windows CE from properly driving audio.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:21 +02:00
Eric Nelson
a3b527a947 nitrogen6x: power-down miscellanous peripherals
Ensure that cameras and USB OTG power are in a stable (reset)
state at reset by configuring their pads and toggling GPIOs.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:21 +02:00
Eric Nelson
41612472b6 nitrogen6x: configure SD2 pads for SDIO on USDHC2
Pads SD2_CLK/CMD/DAT0-3 are connected to an SDIO WiFi device on
Nitrogen and unconnected on BD-SL-i.MX6 (sabre lite).

Configure them as SDIO pins to prevent them from being in a state
that confuses the WiFi part.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:21 +02:00
Troy Kisky
213e9e3348 nitrogen6x: simplify board_mmc_getcd
The same logic applies to both SD card slots, only with different
GPIOs and the code should make that easier to see.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2014-10-06 17:57:20 +02:00
Eric Nelson
c9c86bde3d nitrogen6x: implement board_cfb_skip() to disable text output
Several customers have asked to leave the display quiet during
boot, so allow the user to express this request by the presence
of environment variable "novideo".

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06 17:57:20 +02:00
Nikita Kiryanov
155fa9af95 spi: mxc: fix sf probe when using mxc_spi
MXC SPI driver has a feature whereas a GPIO line can be used to force CS high
across multiple transactions. This is set up by embedding the GPIO information
in the CS value:

cs = (cs | gpio << 8)

This merge of cs and gpio data into one value breaks the sf probe command:
if the use of gpio is required, invoking "sf probe <cs>" will not work, because
the CS argument doesn't have the GPIO information in it. Instead, the user must
use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force
cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must
type "sf probe 15872".

This is inconsistent with the description of the sf probe command, and forces
the user to be aware of implementaiton details.

Fix this by introducing a new board function: board_spi_cs_gpio(), which will
accept a naked CS value, and provide the driver with the relevant GPIO, if one
is necessary.

Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-09-24 17:25:39 +05:30
Fabio Estevam
0a11d6f29c mx6: Remove duplication of iomuxc structure
There is no need to keep iomuxc_base_regs structure as it serves the exact same
purpose of the iomuxc structure, which is to provide access to the GPR
registers.

The additional fields of iomuxc_base_regs are not used. Other advantage of
'iomuxc' is that it has a shorter name and the variable declarations can fit
into a single line.

So remove iomuxc_base_regs structure and use iomuxc instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-07-23 12:25:41 +02:00
Fabio Estevam
3b31605aef nitrogen6x: Fix the PAD settings for the ECSPI chipselect
ECSPI chipselect (MX6_PAD_EIM_D19__GPIO3_IO19) is used with GPIO functionality,
so it does not make sense to set its pad as SPI pin.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-04-28 14:02:39 +02:00
Eric Benard
1220eeb794 nitrogen6x: use common detect_hdmi
Signed-off-by: Eric Bénard <eric@eukrea.com>
2014-04-15 12:23:57 +02:00
Eric Benard
a47e449513 nitrogen6x: use common board_video_skip
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-04-15 12:23:56 +02:00
Marek Vasut
f016f8ca3d usb: mv_udc: Rename to ci_udc
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
2014-02-06 04:48:15 +01:00
Giuseppe Pagano
164d984661 nitrogen6x: Move setup_sata to common part
Move setup_sata function definition from platform file nitrogen6x.c
to arch/arm/imx-common/sata.c to avoid code duplication.

Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
2013-12-17 18:12:14 +01:00
Eric Nelson
10fda48779 i.MX6DQ/DLS: replace pad names with their Linux kernel equivalents
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-11-13 10:19:50 +01:00
Troy Kisky
08ce074e56 nitrogen6x: add otg usb host/device mode support
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:42:40 +02:00
Troy Kisky
7132869d4c mx6: iomux: add GPR1 defines for use with nitrogen6x
Select GPIO1 as the USB OTG ID pin for Nitrogen6x

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:42:40 +02:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Robert Winkler
47ac53d7ae imx: nitrogen6x/mx6qsabrelite: Fix bug in board_video_skip
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
2013-09-10 19:28:18 +02:00
Eric Nelson
67d54c3917 i.MX6: nitrogen6x: Don't bother setting PLL3(480) PFD1 divisor
This clock isn't feeding anything under U-Boot, so there's no
point in changing it from power-on default.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-08-31 18:06:38 +02:00
Eric Nelson
8907c2c504 i.MX6: nitrogen6x: force HDMI onto IPU0/DI0
Our Linux kernel switches the HDMI connector onto IPU0/DI1,
but the U-Boot display driver only supports IPU0/DI0 for the
time being.

Because of this, a soft re-boot will leave the HDMI output
connected to the wrong display port and prevent video from
being displayed.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-08-21 19:20:28 +02:00
Stefano Babic
326ea986ac Merge git://git.denx.de/u-boot-arm
Conflicts:
	board/freescale/mx6qsabrelite/Makefile
	board/freescale/mx6qsabrelite/mx6qsabrelite.c
	include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <sbabic@denx.de>
2013-07-31 11:30:38 +02:00
Robert Winkler
10f779da54 imx: nitrogen6x: mx6qsabrelite: Add support for DVI monitors
A little background is probably appropriate for this patch.

Since "the beginning" of usage of the SABRE Lite and Nitrogen6x
boards, DVI detection has been somewhat broken.

Some (most) DVI monitors don't produce the "HPD" bit in
the PHY_STAT0 register, but do show proper toggling of the
RX_SENSE0..3 bits.

Creating a new the bit-mask to include all five bits and
modifying the 'hdmidet' command and internal detection
routines allows these monitors to function properly in U-Boot.

A related patch to our kernels allows things to work under
Linux:
        7d8752905c

Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-07-27 10:52:42 +02:00
Pardeep Kumar Singla
5ea7f0e328 mx6: Factor out common HDMI setup code
Instead of duplicating HDMI setup code for every mx6 board, factor out the common code

Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
2013-07-27 10:49:36 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Andrew Gabbasov
0c54f4b7c8 mx6: mx6qsabrelite/nitrogen6x: Remove incorrect setting of gpio CS signal
The number of gpio signal is packed inside CONFIG_SF_DEFAULT_CS macro
(shifted and or'ed with chip select), so it's incorrect to pass
that macro directly as an argument to gpio_direction_output() call.

Also, SPI driver sets the direction and initial value of a gpio,
used as a chip select signal, before any actual activity happens
on the bus.

So, it is safe to just remove the gpio_direction_output call,
that works incorrectly, thus making no effect, anyway.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2013-06-03 13:25:46 +02:00
Benoît Thébaudeau
7e2173cf82 imx: iomux-v3: Include PKE and PUE to pad control pull definitions
PUE requires PKE to mean something, as do pull values with PUE, so do not
compell users to explicitly use PKE and PUE everywhere. This is also what is
done on Linux and what has already been done for i.MX51.

By the way, remove some unused pad control definitions.

There is no change of behavior.

Note that SPI_PAD_CTRL was defined by several boards with a pull value, but
without PKE or PUE, which means that no pull was actually enabled in the pad.
This might be a bug in those boards, but this patch does not change the
behavior, so it just removes the meaningless pull value from those definitions.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-28 11:15:07 +02:00
Fabio Estevam
38e7007725 mx6: Fix get_board_rev() for the mx6 solo case
When booting a Freescale kernel 3.0.35 on a Wandboard solo, the get_board_rev()
returns 0x62xxx, which is not a value understood by the VPU
(Video Processing Unit) library in the kernel and causes the video playback to
fail.

The expected values for get_board_rev are:
0x63xxx: For mx6quad/dual
0x61xxx: For mx6dual-lite/solo

So adjust get_board_rev() accordingly and make it as weak function, so that we
do not need to define it in every mx6 board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-04-03 11:36:34 +02:00
Abbas Raza
aad4659a2f mmc: i.MX6: fsl_esdhc: Define maximum bus width supported by a board
Maximum bus width supported by some i.MX6 boards is not 8bit like
others. In case where both host controller and card support 8bit transfers,
they agree to communicate on 8bit interface while some boards support only 4bit interface.
Due to this reason the mmc 8bit default mode fails on these boards. To rectify this,
define maximum bus width supported by these boards (4bit). If max_bus_width is not
defined, it is 0 by default and 8bit width support will be enabled in host
capabilities otherwise host capabilities are modified accordingly.

It is tested with a MMCplus card.

Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
cc: stefano Babic <sbabic@denx.de>
cc: Andy Fleming <afleming@gmail.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2013-04-03 11:26:28 +02:00
fabio.estevam@freescale.com
19a0f7fa27 nitrogen: Use unsigned long to specify the total RAM size
When building for the nitrogen boards with 2GiB the following warning happens:

nitrogen6x.c:89:38: warning: integer overflow in expression [-Woverflow]

2GiB can not fit in 32-bits, so use ulong instead.

Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-03-15 14:39:44 +01:00
Eric Nelson
d67b0d97b1 Add Boundary Devices Nitrogen6X boards
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-03-13 09:04:24 +01:00