Commit graph

49061 commits

Author SHA1 Message Date
Andre Przywara
06a57f656b arm: dts: sunxi: update A64 to new EMAC binding
The U-Boot driver for the sun8i-emac was using some preliminary DT
binding. Now since Linux got its own driver in v4.15 and our driver
can now cope with both bindings, let's convert the DT nodes used for the
Pine64+ board over to the new bindings used by the kernel.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04 11:31:35 +05:30
Andre Przywara
12afd95711 net: sun8i-emac: add support for new EMAC DT binding
The Ethernet MAC used in newer Allwinner SoCs (H3, A64, H5) got an
upstream Linux driver in v4.15.
This one uses a slightly different binding from the original one used
by the U-Boot driver.
The differences to the old binding are:
- The "syscon" address is held in a separate node, referenced via a
  phandle in the "syscon" property.
- The reference to the PHY is held in a property called "phy-handle",
  not "phy".
- The PHY register is at offset 0x30 in the syscon device, not at 0.
- The internal PHY is activated when the node, which phy-handle points
  to, is a child node of an "allwinner,sun8i-h3-mdio-internal" node.

Teach the U-Boot driver how to find its resources in a "new-style" DT,
so that we can use a Linux kernel compatible DT for U-Boot as well.
This keeps support for the old binding for now, to allow a smooth
transition.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04 11:31:35 +05:30
Andre Przywara
c034117302 net: sun8i-emac: support new pinctrl DT bindings
The Linux kernel driver for the Allwinner pin controller gained support
for generic properties, which are now also used in the DTs.
The sun8i-emac Ethernet driver for new Allwinner MACs reads the pins from
the DT, but so far only supported the old binding.
Update the parsing routine to cope with both the old and new bindings,
so that the newer DTs can be used with U-Boot and its Ethernet driver.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04 11:31:35 +05:30
Andre Przywara
381996c5ed sunxi: gpio: add missing compatible strings
The sunxi GPIO driver is missing some compatible strings for recent
SoCs. While most of the sunxi GPIO code seems to not rely on this (and
so works anyway), the sunxi_name_to_gpio() function does and fails at
the moment (for instance when resolving the MMC CD pin name).
Add the compatible strings for the A64 and V3s, which were missing
from the list. This now covers all pinctrl nodes in our own DTs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04 11:31:35 +05:30
Andre Przywara
35debf8a45 sunxi: README.sunxi64: Add hint about non-debug of ARM Trusted Firmware
As we are running into issues where the final U-Boot FIT image file is
exceeding our size limit, add a hint to the README.sunxi64 file
to point out the possibility of building non-debug versions of the ATF
binary. These are about 12KB smaller than the standard debug build, and
so allow successful U-Boot builds for many boards with the Allwinner H5
SoC.
Please note that under normal circumstances the debug build is still
recommended, as it gives valuable clues in case something goes wrong in
the ATF.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04 11:31:35 +05:30
Miquel Raynal
e71553fe75
configs: add NAND support for NES Classic
Add NAND parameters to the Nintendo NES Classic configuration file which
features a Macronix NAND flash chip with 128kiB blocks of 2kiB pages
plus 64 OOB bytes.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:13:36 +02:00
Miquel Raynal
748b5b34d3
sunxi: move the NAND parameters to Kconfig
Move the NAND parameters from defconfig files to Kconfig for SUNXI
architecture only. Fort now only the CHIP pro is migrated.

It would have been better to convert this defconfig entry to Kconfig for
all supported machines/architectures but it has been abandoned due to a
fairly high amount of errors reported by the moveconfig.py tool. This is
due to defines quite often being multiplications of values/other defines
not correctly handled.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:13:32 +02:00
Miquel Raynal
b56052f4ca
sunxi: make NAND_SUNXI use ARCH_SUNXI as default in Kconfig
Remove NAND_SUNXI from the CHIP pro defconfig to be automatically
selected depending on the state of ARCH_SUNXI.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:13:27 +02:00
Miquel Raynal
6d094d535c
sunxi: automatically select SPL_NAND_SUPPORT in Kconfig
Make SUNXI_NAND select SPL_NAND_SUPPORT in Kconfig, this limit the
number of entries to add in defconfig files when adding NAND support.

For now, the only board using it is the CHIP pro.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:13:06 +02:00
Miquel Raynal
491feffa88
sunxi: dts: enable NAND on NES classic
Let the Nintendo NES Classic use the Macronix NAND chip on it.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:56 +02:00
Miquel Raynal
663e8a9b54
sunxi: allow NAND support to be compiled for sun8i platforms
Add some clocks/PLL definitions as well as the dependency on MACH_SUN8I
in Kconfig.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:52 +02:00
Miquel Raynal
136e325933
sunxi: spl: remove DMA related settings of the NAND controller
Code has been changed to do not use DMA anymore with the NAND
controller, instead PIO is used. Then, DMA-specific initialization may
be dropped.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:48 +02:00
Miquel Raynal
6ddbb1e936
spl: nand: sunxi: use PIO instead of DMA
SPL support was first written to support only the earlier generations of
Allwinner SoCs, and was only really enabled on the A13 / GR8. However,
those old SoCs had a DMA engine that has been replaced since the A31 by
another DMA controller that is no longer compatible.

Since the code directly uses that DMA controller, it cannot operate
properly on the later SoCs, while the NAND controller has not changed.

There's two paths forward, the first one would have been to add support
for that DMA controller too, the second to just remove the DMA usage
entirely and rely on PIO.

The later has been chosen because CPU overload at this stage is not an
issue and it makes the driver more generic, and easier to understand.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:43 +02:00
Miquel Raynal
7440bd7885
spl: nand: sunxi: declare the ecc_bytes array globally
Move the ecc_bytes array out of nand_max_ecc_strength() for future use
by nand_read_page().

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:38 +02:00
Miquel Raynal
ba1c98bae2
sunxi: spl: deassert the NAND controller reset line
Ensure the NAND controller reset line is deasserted before use.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:32 +02:00
Miquel Raynal
22f0aa0528
spl: nand: sunxi: make the reset column helper more generic
Prepare the future use of an helper to move the data pointer (the
column) of the NAND chip by renaming nand_reset_column() to
nand_change_column(). Resetting the column is just a matter of giving 0
as argument.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:28 +02:00
Miquel Raynal
4dac80a5e9
spl: nand: sunxi: ensure enough time has passed after changing the column
When changing the column, the ONFI specification states that a minimum
time of tCCS (Change Column Setup time) must elapse between the last
address cycle is asserted on the bus and the first data cycle is
clocked. An usual value for average NANDs is 500 nanoseconds. Round it
up to 1 microsecond to be safe.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:22 +02:00
Miquel Raynal
a084cb6664
spl: nand: sunxi: create an helper to handle command execution
Executing a command is matter of always doing the following sequence:
  * Waiting for the FIFO to be empty so we can fill it with the new
    command.
  * Clearing the status register.
  * Writing the command in the FIFO.
  * Waiting for the command to finish.

Add a nand_exec_cmd() helper to handle this instead of repeating the
logic through the various functions.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:17 +02:00
Miquel Raynal
781e70cff1
spl: nand: sunxi: add missing status clear
It is best practice to always clear the status register before executing
a command to be sure that the status read afterwards is relevant.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:13 +02:00
Miquel Raynal
60fb179133
spl: nand: sunxi: introduce the nand_wait_cmd_fifo_empty() helper
One bit in the control registers indicates if the NAND controller is
ready to receive a new command. Otherwise, the command FIFO is full and
we should wait for this bit to flip. It then states that the last
command has been processed and the FIFO is now free to welcome another
command.

Add this sanity check before starting any new command.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:07 +02:00
Miquel Raynal
28f7a9d375
spl: nand: sunxi: introduce the nand_wait_int() helper
The pattern of polling on a status register until a bit is set or a
timeout occurs is repeated multiple times in the driver. Mutualize the
code by introducing the nand_wait_int() helper that does wait for the
bit to flip or returns an error in case of timeout.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:04 +02:00
Miquel Raynal
802f766994
spl: nand: sunxi: fix typo on register name
Change NFC_SEND_ADR to NFC_SEND_ADDR.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:10:59 +02:00
Miquel Raynal
a0a984e14a
spl: nand: sunxi: fix second case of modulo by zero error
In the nand_read_buffer() step, the seed is calculated by doing a modulo
by conf->nseeds which is always zero when not using the randomizer (most
of SLC NANDs).

This situation turns out to lead to a run time freeze with certain
toolchains.

Derive this seed only when the randomizer is enabled (and conf->nseeds
logically not zero), exactly like what has been done before with an
identical situation, see commit ea3f750c73 ("nand: sunxi: Fix modulo
by zero error").

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:10:55 +02:00
Miquel Raynal
f3aff37689
mtd: nand: sunxi: fix ECC strength choice
When the requested ECC strength does not exactly match the strengths
supported by the ECC engine, the driver is selecting the closest
strength meeting the 'selected_strength > requested_strength'
constraint. Fix the fact that, in this particular case, ecc->strength
value was not updated to match the 'selected_strength'.

For instance, one can encounter this issue when no ECC requirement is
filled in the device tree while the NAND chip minimum requirement is not
a strength/step_size combo natively supported by the ECC engine.

Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:10:46 +02:00
Miquel Raynal
55fe0e2b54
spl: fix binman_sym output check
A previous commit introduced the use of binman in the SPL.

After the binman_sym call over the 'pos' symbol, the output value is
checked against BINMAN_SYM_MISSING (-1UL). According to the
documentation (tools/binman/README), when it comes to the 'pos'
attribute:

pos:
	This sets the position of an entry within the image. The first
	byte of the image is normally at position 0. If 'pos' is not
	provided, binman sets it to the end of the previous region, or
	the start of the image's entry area (normally 0) if there is no
	previous region.

So instead of checking if the return value is BINMAN_SYM_MISSING, we
should also check if the value is not null.

The failure happens when using both the SPL file and the U-Boot file
independently instead of the concatenated file (SPL + padding + U-Boot).
This is because the U-Boot binary file alone does not have the U-Boot
header while it is present in the concatenation file. Not having the
header forces the SPL to discover where it should load U-Boot. The
binman_sym call is supposed to do that but fails. Because of the wrong
check, the destination address was set to 0 while it should have been
somewhere in RAM. This, obviously, stalls the board.

Fixes: 8bee2d251a ("binman: Add binman symbol support to SPL")
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:10:24 +02:00
Jagan Teki
0354f4bef0 sunxi: Add DRAM_SUN8I_A83T kconfig entry
Add proper and simple kconfig option for dram_sun8i_a83t.c
instead of using MACH type on Makefile.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 16:46:47 +05:30
Jagan Teki
c335e9903c sunxi: Add DRAM_SUN8I_A33 kconfig entry
Add proper and simple kconfig option for dram_sun8i_a33.c
instead of using MACH type on Makefile.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 16:46:44 +05:30
Jagan Teki
af30393cb5 sunxi: Add DRAM_SUN8I_A23 kconfig entry
Add proper and simple kconfig option for dram_sun8i_a23.c
instead of using MACH type on Makefile.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 16:46:41 +05:30
Jagan Teki
7d0b165d5e sunxi: Add DRAM_SUN9I kconfig entry
Add proper and simple kconfig option for dram_sun9i.c
instead of using MACH type on Makefile.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 16:46:37 +05:30
Jagan Teki
dd928bfbb6 sunxi: Add DRAM_SUN4I kconfig entry
Add proper and simple kconfig option for dram_sun4i.c
instead of using MACH type on Makefile.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 16:46:14 +05:30
Jagan Teki
fdfa934e6e sunxi: add DRAM_SUN6I kconfig
Add proper and simple kconfig option for dram_sun6i.c
instead of using MACH type on Makefile.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 15:37:20 +05:30
Jagan Teki
735fb25202 sunxi: Add AXP_PMIC_BUS kconfig entry
Add simple and meaningful kconfig option for pmic_bus.c
instead of using MACH type on Makefile.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 15:37:20 +05:30
Jagan Teki
6f6f883949 sunxi: Add SUN8I_RSB kconfig entry
Add simple and meaningful kconfig option for rsb.c
instead of using MACH type on Makefile.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 15:37:20 +05:30
Jagan Teki
63928fa6dd sunxi: Use SUN6I_PRCM if used
SUN6I_PRCM is also used for SUN8I and SUN9I, so
select the same on respective MACH types.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 15:37:20 +05:30
Jagan Teki
71d9edf47a sunxi: Add SUN6I_P2WI kconfig entry
Add simple and meaningful kconfig option for p2wi.c
instead of using MACH type on Makefile.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 15:37:20 +05:30
Jagan Teki
2aa697a494 sunxi: Add SUN6I_PRCM kconfig entry
Add simple and meaningful kconfig option for prcm.c
instead of using MACH type on Makefile.

PRCM (Power/Reset/Clock Management) is considered as a
Multi-Functional Device, so used the same on Kconfig definition.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19 15:37:20 +05:30
Patrick Delaunay
b8aa55cb64 common: move init_helpers.h prototypes in init.h
Merge init_helpers.h in the new file init.h
with only prototypes for init_cache_f_r
used in common/board_f.c

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-16 14:56:59 -04:00
Patrick Delaunay
fc22ee215a common: move board_info.c prototypes in init.h
Move function prototype for common/init/board_init.c
from common.h to init.h

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-16 14:56:59 -04:00
Patrick Delaunay
e2c219cd71 common: move board_r.c prototypes in init.h
Move function prototypes used in common/board_r.c
from common.h to init.h

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-16 14:56:59 -04:00
Patrick Delaunay
11f86cbaff common: move board_init.c prototypes in init.h
Move function prototypes for common/init/board_init.c
from common.h to init.h

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-16 14:56:00 -04:00
Patrick Delaunay
d6f8771239 common: move board_f.c prototypes in init.h
Move prototypes for function used in common/board_f.c
from common.h to init.h
Remove weak for arch_reserve_stacks in prototype
(checkpatch issue)

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-16 14:56:00 -04:00
Michal Simek
71b7564479 ppc: Remove orphan xilinx_irq.h file
This file is completely unused and it should be removed as the part of
ppc405/ppc440 xilinx platform removal.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-16 14:54:14 -04:00
Heinrich Schuchardt
02c5e891a3 MAINTAINERS: TI SYSTEM SECURITY: remove invalid file
Remove a link to a non-existent file.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Andrew F. Davis <afd@ti.com>
2018-03-16 14:54:14 -04:00
Heinrich Schuchardt
c133915eb2 MAINTAINERS: ARM TI: remove invalid paths
Remove non-existing paths.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-03-16 14:54:14 -04:00
Heinrich Schuchardt
cbc4423e87 MAINTAINERS: ARM SAMSUNG: remove invalid paths
Remove non-existing directories.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2018-03-16 14:54:14 -04:00
Heinrich Schuchardt
18fa6230ce MAINTAINERS: FLATTENED DEVICE TREE: correct maintained path
Change due to commit b08c8c4870 ("libfdt: move headers to
<linux/libfdt.h> and <linux/libfdt_env.h>")

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-03-16 14:54:14 -04:00
Heinrich Schuchardt
0f8525f5c1 MAINTAINERS: ARM HISILICON: correct maintained path
Fix an incorrect path.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-03-16 14:54:14 -04:00
Heinrich Schuchardt
f7b2849a47 MAINTAINERS: ARM FREESCALE IMX: remove invalid path
arch/arm/cpu/armv7/mx*/ does not relate to any existing directory.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-03-16 14:54:14 -04:00
Patrick Delaunay
f7bd1c3c97 post: remove reference to power functions
The 2 functions board_power_mode and board_poweroff
are no more existing in U-Boot code (check with grep)
This patch updates the documentation and removes
the unnecessary prototypes.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-16 14:54:14 -04:00
Patrick Delaunay
e6e92170a4 common: remove unused prototypes
Remove the prototypes for 4 functions no more existing
in U-Boot code (checked by grep):
- checkflash
- checkdram
- mdm_init
- setup_board_extra

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-16 14:54:14 -04:00