The PERSIST_SECONDARY_BOOT is in GPR10 address 0x30390098, adjust the
text which currently says it is in GPR0 while using the correct address
of GPR10.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add code to build the eMMC variant of the Colibri iMX6ULL, i.e. the
'Colibri iMX6ULL 1GB' which has a eMMC instead of the raw NAND used
on other SKUs.
Related-to: ELB-4056, ELB-4057
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Integrate new Toradex SKU 0062 Colibri iMX6ULL 1GB IT. This commit
basically adjusts three parameters of the RAM settings:
Increase density from 4Gb to 8Gb
Increase ROW address from 15 to 16
Increase tRFC (refresh command time) from 260 to 350
This timing is valid for all Toradex Colibri iMX6ULL SKUs
Related-to: ELB-4055, ELB-4057
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add new i.MX 6ULL and 8M Plus SKUs to ConfigBlock handling:
0062: Colibri iMX6ULL 1GB IT (eMMC)
0063: Verdin iMX8M Plus Quad 4GB IT
0064: Verdin iMX8M Plus Quad 2GB Wi-Fi / BT IT
0065: Verdin iMX8M Plus QuadLite 1GB IT
0066: Verdin iMX8M Plus Quad 8GB Wi-Fi / BT
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Restore "Is the module an IT version? [y/N]" for "cfgblock create"
interactive mode command, which was leading to invalid detection
of 0051 Colibri iMX8DX 1GB WB module;
Fixes: a5b5ad4d85 ("toradex: tdx-cfg-clock: add new i.mx 8m mini/plus skus")
Related-to: ELB-3482
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Also take over maintainership of remaining Toradex SoMs as Oleksandr
has left our company.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
CC: Oleksandr Suvorov <cryosay@gmail.com>
After the conversion to binman in commit 8996e6b7c6 ("imx8mm_evk: switch
to use binman to pack images"), it is necessary to flash both flash.bin and
u-boot.itb to get a bootable system. Prior to this commit, only flash.bin
was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single
bootable binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone
(for example, for secure boot purposes).
Also update imx8mm_evk.rst to remove the u-boot.itb copy step.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
NXP used to setup the gpmi clock root from gpmi_clk in early versions
in their downstream BSP. [1]
However on mainline the gpmi clock root was always setup from enfc
since the beginning of the i.MX 6 series SoCs, which is still the same
today. [2]
NXP followed the mainline approach at some point and changed
setup_gpmi_io_clk to setup gpmi clock root from enfc which left faulty
code behind in our board file. [3]
This commit follows the change of NXP as it improves the performance of
the NAND from ~1.2 MiB/s to ~12 MiB/s. [3]
This change was verified to work in recovery-mode and u-boot loaded
from NAND on all four Colibri iMX6ULL SKUs from Toradex.
The frequency used to read the NAND, measured on RE# (Read Enable):
before this patch: 1.4 MHz
after this patch: 22 MHz
in Linux Kernel: 50 MHz
[1] https://source.codeaurora.org/external/imx/uboot-imx/tree/arch/arm/cpu/armv7/mx6/clock.c?h=nxp/imx_v2016.03_4.1.15_2.0.0_ga#n62
[2] commit 23608e23fd ("i.mx: add the initial support for freescale i.MX6Q processor")
[3] https://source.codeaurora.org/external/imx/uboot-imx/commit/?id=7a82a19ceabfb04bbc1591a67c99751748781c7d
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Finally, found the root cause of the issue already once mentioned back
here [2] which caused the following error message during boot:
imx_wdt watchdog@30280000:
pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
Turns out while the watchdog node itself was already u-boot,dm-spl its
pinctrl node was not which caused it to be unavailable at that early
stage. Note that any and all other boards I checked also seem to be
missing this. However, I can't judge whether or not they might indeed
need a similar fix or not.
[2] https://marc.info/?l=u-boot&m=161786572422973
Fixes: commit d304e7ace3
("ARM: imx8m: Fix reset in SPL on Toradex iMX8MM Verdin")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable and set preboot var with fdtfile evaluation.
It will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Variable "kernel_image" is used in boot.scr script only, that sets its
own default value to the constant string @@KERNEL_IMAGETYPE@@ in case
"kernel_image" is not set.
The default name of the kernel image shipped with BSP 5.x is "Image.gz".
Setting kernel_image="Image" as a pre-defined u-boot variable
breaks booting systems with modern versions of boot.scr, whereas
renaming it fixes booting with modern scripts and does not break working
of earlier versions of boot.scr.
While at it also update the copyright period, rather than hard-coding
fdtfile default fdt_board to dev for the Verdin iMX8M Mini and fix its
closing #endif comment.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
We drop support for Verdin iMX8M Mini V1.0B.
Related-to: ELB-3551
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This powers some peripherals on the carrier board e.g. the USB hub.
Related-to: ELB-3206
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Prepare for DEK blob encapsulation support through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application
call. U-boot sends and receives the DEK and the DEK blob binaries
through OP-TEE dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Taken from NXP's commit 56d2050f40 ("imx8m: Add DEK blob encapsulation
for imx8m").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Turns out Microship (formerly Micrel) meanwhile integrated proper
support for the DLL setup on their KSZ9131. Unfortunately, this
conflicts with our previous board code doing that.
Fix this by getting rid of our board code and just relying on the
generic implementation relying on rgmii-id being used as phy-mode.
Fixes: commit c6df0e2ffd
("net: phy: micrel: add support for DLL setup on ksz9131")
Fixes: commit af2d3c91d8
("ARM: dts: imx8mm-verdin: Set PHY mode to RGMII-ID")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Due to missing configs, CI goes in deadlock until an OOM is tracked. Add
CONFIG_SYS_LOAD_ADDR and replace CONFIG_SYS_EXTRA_OPTIONS with
CONFIG_IMX_CONFIG.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Ying-Chun Liu (PaulLiu)" <paul.liu@linaro.org>
CC: Fabio Estevam <festevam@denx.de>
Even if board can be successfuly built, CI goes in deadlock (see thread
on https://www.mail-archive.com/u-boot@lists.denx.de/msg419663.html).
This is caused by SYS_CONFIG set in header file and because defconfig
for the board is out of sync with Kconfig. As result, buildman goes on
to read from stdin until an OOM is reached.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Frieder Schrempf <frieder.schrempf@kontron.de>
Hex and int Kconfig options are supposed to have defaults. This is so we
can configure U-Boot without having to enter particular values for the
items that don't have specific values in the board's defconfig file.
If this rule is not followed, then introducing a new Kconfig can produce
a loop like this:
Break things (BREAK_ME) [] (NEW)
Error in reading or end of file.
Break things (BREAK_ME) [] (NEW)
Error in reading or end of file.
The continues forever since buildman passes /dev/null to 'conf', and
the build system just tries again. Eventually there is so much output that
buildman runs out of memory.
We can detect this situation by looking for a symbol (like 'BREAK_ME')
which has no default (the '[]' above) and is marked as new. If this
appears multiple times in the output, we know something is wrong.
Add a filter function for the output which detects this situation. Allow
it to return True to terminate the process. Implement this termination in
cros_subprocess.
With this we get a nice message:
buildman --board sandbox -T0
Building current source for 1 boards (0 threads, 32 jobs per thread)
sandbox: w+ sandbox
+.config:66:warning: symbol value '' invalid for BREAK_ME
+
+Error in reading or end of file.
+make[3]: *** [scripts/kconfig/Makefile:75: syncconfig] Terminated
+make[2]: *** [Makefile:569: syncconfig] Terminated
+make: *** [Makefile:177: sub-make] Terminated
+(** did you define an int/hex Kconfig with no default? **)
Signed-off-by: Simon Glass <sjg@chromium.org>
At present buildman does not write any output (to the 'out' and 'err)
files if the build terminates with a fatal error. This is to avoid adding
lots of spam to the logs.
However there are times when this is actually useful, such as when the
build fails for an obscure reason such as a Kconfig loop.
Update the logic to always write the output, so that the user gets a clue
as to what is happening.
Signed-off-by: Simon Glass <sjg@chromium.org>
io read/write may cause wrong result because they may read/write data
from/to register instead of memory. Add 'volatile' to avoid it.
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The following warning is seen in unleashed.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast with uintptr_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The following warning is seen in sifive_ddr.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_index_ptr().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The following warning is seen in macb.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_index_ptr(), or cast with uintptr_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Like dev_read_addr_ptr(), provide a wrapper for the indexed version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present there is only devfdt_get_addr_ptr() which only returns
the first <addr, size> pair in the 'reg' property. Add a new API
devfdt_get_addr_index_ptr() to return the indexed pointer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The following warning is seen in ocores_i2c.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_ptr().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
dev_read_addr() returns a value of type fdt_addr_t which is a 64-bit
address and plat->base is a pointer. In a 32-bit build, this causes the
following warning seen when building sifive-gpio.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_ptr().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
dev_read_addr() returns a value of type fdt_addr_t which is a 64-bit
address and pd->va is a pointer. In a 32-bit build, this causes the
following warning seen when building sifive-prci.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_ptr().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The following warning is seen in cache-sifive-ccache.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Fix by casting it with uintptr_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Commit 47d73ba4f4 ("board: sifive: overwrite board_fdt_blob_setup in u-boot proper")
added a board-specific implementation of board_fdt_blob_setup() which
takes a pointer as the return value, but it does not return anything
if CONFIG_OF_SEPARATE is not enabled. This will cause a build warning
seen when testing booting S-mode U-Boot directly from QEMU, per the
instructions in [1]:
board/sifive/unleashed/unleashed.c: In function ‘board_fdt_blob_setup’:
board/sifive/unleashed/unleashed.c:125:1: warning: control reaches end of non-void function [-Wreturn-type]
Return &_end as the default case.
[1] https://qemu.readthedocs.io/en/latest/system/riscv/sifive_u.html#running-u-boot
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function")
implemented .enable, so fixed rate clocks can be used where drivers
might call clk_enable(). Implement the .disable op for the same reason;
some drivers, e.g. USB PHYs, may attempt to disable clocks at runtime.
Signed-off-by: Samuel Holland <samuel@sholland.org>
While we intentionally set -std=gnu11 for building host tools, and have
for quite some time, we never dropped -std=gnu99 from tools/Makefile.
This resulted in passing -std=gnu11 ... -std=gnu99 when building, and
gnu99 would win. This in turn would result now in warnings such as:
tools/mkeficapsule.c:25:15: warning: redefinition of typedef 'u32' is a C11 feature [-Wtypedef-redefinition]
typedef __u32 u32;
^
Signed-off-by: Tom Rini <trini@konsulko.com>
This enables the clock controller driver support on TI's SoCs. This will
fix this GPIO issue at boot time:
request_and_set_gpio: Unable to request GPIO_PR1_MII_CTRL
request_and_set_gpio: Unable to request GPIO_MUX_MII_CTRL
request_and_set_gpio: Unable to request GPIO_FET_SWITCH_CTRL
request_and_set_gpio: Unable to request GPIO_PHY_RESET
This issue comes from the fact that the clock controller is not probed.
Enable the TI's clock controller driver support to solve this.
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
At present U-Boot always builds dtc if CONFIG_OF_CONTROL is defined, even
when DTC is provided. The built dtc is not actually used, so this is a
waste of time.
Update the Makefile logic to build dtc only if one is not provided to the
build with the DTC variable. Add documentation to explain this.
This saves about 3.5 seconds of elapsed time on a clean build of
sandbox_spl for me.
Signed-off-by: Simon Glass <sjg@chromium.org>
