Support load of the U-Boot image from raw SATA disk sector. This is
equivalent to load from MMC raw sector.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Use CONFIG_IS_ENABLED(WDT) to permit use of WDT in SPL without DM,
while the full U-Boot can use rich DM/DT WDT driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Suniel Mahesh <sunil.m@techveda.org>
On some platform we have sufficient memory available early on to allow
setting up and using a basic BSS prior to entering board_init_f(). Doing
so can for example be used to carry state over to board_init_r() without
having to resort to extending U-Boot's global data structure.
To support such scenarios add a Kconfig option called CONFIG_SPL_EARLY_BSS
to allow moving the initialization of BSS prior to entering board_init_f(),
if enabled. Note that using this option usually should go along with using
CONFIG_SPL_SEPARATE_BSS and configuring BSS to be located in memory
actually available prior to board_init_f().
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.
To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
When we have a FIT image being used by SPL by default that means the
most common case is that we'll never run into a legacy image. Disable
legacy image support by default in that case to reclaim space.
Signed-off-by: Tom Rini <trini@konsulko.com>
This allows to silence ubi and ubispl individually.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
The motivation is to use the UBI atomic volume rename functionality to
allow double copy software updates on UBI. To that end the SPL is
configured to always load the same volume name (e.g. "u-boot"),
whereas a software updater always installs into the secondary volume
"u-boot_r". After successful installation, these two volume names are
switched.
This extension is protected by #ifdefs as it will somewhat slow down
loading of volumes by id. This is because the code needs to disable
the optimization of ignoring all volume ids which are not
to-be-loaded, since these can only be resolved after attaching.
This adds two vtbl related functions from Linux, which are taken from
the same kernel version as the current main U-Boot UBI code (Linux 4.2
64291f7db5bd8).
Signed-off-by: Hamish Guthrie <hamish.guthrie@kistler.com>
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Move the ubispl configuration to KConfig and drop them from the
whitelist.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Javier Martínez Canillas <javier@dowhile0.org>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a
choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and
CONFIG_SPL_SPI_BOOT. Migrate this to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
As explained in include/configs/imx6_spl.h. the i.MX6 SPL
size limit is 68KB (4KB header + 64KB max size).
Provide such limit for all i.MX6 boards that use SPL
to detect SPL size overflow in build time.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJc+lyDAAoJEB6zHgIOrC/I2MQH/A20fKVWQcnvmwwuJ8w/QNZ5
syNqpRLgw8jIMuLgmnUOQmjhKEsdcNWlESQt+eppTH2yMTSwNlQVT8SVE2s1podP
QKBSHw4V5UXlYZwZBhrrmL3twVOf6oecoE4gzpnh1ydMHiC1zcHAJuutlNw8y+ye
IVrojVPu5miN91TJuvkcGdafNdFVO4mBMhGhCFA4VN38OI6Dk/fQg4QBrxj/3XWb
+EOznxL1YZYGf8hhYqe68vMVVVT5sSq1SbId6JGHRkAYDcn/qKOuOkzW7FP7tbi/
PidcTmfqOFH1EYnincxQ1cXyhaSs/VOxRHIWgzlRIJJHHp0o7Y+FUGAilSGKHso=
=tnXy
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel fixes for 2019.07 cycle
When introduced this limit was an int but was then changed to hex
without noting as much in the prompt nor changing existing users. Put
this back to an int.
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Fixes: 2577015dc5 ("spl: add overall SPL size check")
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds a size check for SPL that can dynamically check generated
SPL binaries (including devicetree) for a size limit that ensures
this image plus global data, heap and stack fit in initial SRAM.
Since some of these sizes are not available to make, a new host tool
'spl_size_limit' is added that dumps the resulting maximum size for
an SPL binary to stdout. This tool is used in toplevel Makefile to
implement the size check on SPL binaries.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
By default the configuration of the PMC is to have an external crystal
connected that requires driving on both XIN and XOUT pins.
The bypass configuration means that only XIN will be used, the SoC will not
do any driving, and the XIN needs to be provided with a proper signal.
This is the MOSCXTBY bit in the PMC main clock generator register.
The SPL needs to properly initialize the PMC registers before switching
to external clock signal and raising the clock to the cruise speed.
Also created Kconfig for this specific configuration.
By default this is disabled.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
SPL currently does not check uImage CRCs when loading U-Boot.
This patch adds checking the uImage CRC when SPL loads U-Boot. It does
this by reusing the existing config option SPL_CRC32_SUPPORT to allow
leaving out the CRC check on boards where the additional code size or
boot time is a problem (adding the CRC check currently adds ~1.4 kByte
to flash).
The SPL_CRC32_SUPPORT config option now gets enabled by default if SPL
support for legacy images is enabled to check the CRC on all boards
that don't actively take countermeasures.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
SPL only needs to be able to read from SPI Flash to load next stage and
does not really need write/erase etc. Therefore in order to reduce SPI
Flash code size in SPL, enable SPI_FLASH_TINY, that only supports
reading from SPI flash, as default.
Note: Since, SPI_FLASH_TINY does not support SPI_FLASH_BAR,
SPI_FLASH_TINY is not enabled for boards with SPI controllers that
cannot support 4 byte addressing.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.
Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from
Linux. This allows auto detection and configuration of Flash parameters.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Most of the time SPL only needs very simple FAT reading, so having
CONFIG_IS_ENABLED(FAT_WRITE) to exclude it from SPL build would help
to save 64KiB default max clustersize from memory.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
If we don't define CONFIG_SPL_FIT_IMAGE_TINY, when loading images from FIT,
the SPL will record all loadables' info to u-boot's FDT. This causes
problem when HAB is enabled, because FDT's content is modified before
we authenticate it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Building U-Boot with CONFIG_PCI and CONFIG_DM_PCI enabled, but
CONFIG_SPL_PCI_SUPPORT disabled, results in following linker
error:
lib/built-in.o: In function `fdtdec_get_pci_bar32':
lib/fdtdec.c:305: undefined reference to `dm_pci_read_bar32'
fdtdec.c:305:(.text.fdtdec_get_pci_bar32+0x24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `dm_pci_read_bar32'
This is because reference to dm_pci_read_bar32() remains in lib/fdtdec.c
while SPL build does not descend into drivers/pci directory in
drivers/Makefile if CONFIG_SPL_PCI_SUPPORT is not enabled.
Fix this by applying appropriate #define guards in lib/fdtdec.c.
It looks like ns16550.c has the same problem, so fixed that too.
To simplify this, CONFIG_SPL_PCI_SUPPORT is renamed to CONFIG_SPL_PCI
(enables use of CONFIG_IS_ENABLED() macro).
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function part_init() will only be built when we have both
CONFIG_PARTITIONS and CONFIG_HAVE_BLOCK_DEVICE set. Protect the call to
this function with both of these tests now.
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is some basic informaton that SPL normally wants to pass through to
U-Boot, such as the SDRAM size and bank information.
Mkae use of the new bloblist structure for this. Add a new 'handoff' blob
which is set up in SPL and passed to U-Boot proper. Also adda test for
sandbox_spl that checks that this works correctly and a new 'sb' command
to show the information passed from SPL.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than having a negative option, make this a positive option and
enable it by default. This makes it easier to understand.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these subsystems are only supported in U-Boot proper but it is
sometimes necessary to support them in SPL, or even TPL. Update the
Kconfig and Makefile to support this. Also adjust GPIO so that it can be
used in TPL if required.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
OP-TEE is an open source trusted OS, in armv7, its loading and
running are like this:
loading:
- SPL load both OP-TEE and U-Boot
running:
- SPL run into OP-TEE in secure mode;
- OP-TEE run into U-Boot in non-secure mode;
To make code simple, it would be fine to use IH_OS_TEE for the
os tyle in TPL(just like IH_OS_LINUX is using both in SPL and U-Boot).
Here is the diagram for SPL loading OP-TEE,
IH_OS_TEE:(make u-boot.itb for SPL)
Non-Secure Secure
BootROM
|
v
SPL
|
v
--------- OP-TEE
|
v
U-Boot
|
V
Linux
For other two king of OP-TEE loading/booting, see commit message:
45b55712d4 image: Add IH_OS_TEE for TEE chain-load boot
More detail:
https://github.com/OP-TEE/optee_os
and search for 'boot arguments' for detail entry parameter in:
core/arch/arm/kernel/generic_entry_a32.S
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replaced misspelled words "parition"/"paritioning" (missing 't') in two
Kconfig files by correct words "partition"/"partitioning"
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add CONFIG_SPL_POWER_DOMAIN config entry.
Build drivers/power/domain if this config is selected.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allwinner H6 is a new SoC from Allwinner features USB3 and PCIe
interfaces.
This patch adds support for it.
The corresponding DTSI file, from Linux next-20180720, is also
introduced.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some legacy boards use RAW image for SPL boot. Add Kconfig option
SPL_PAYLOAD to set alternative image.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rename CONFIG_SPL_RESET_SUPPORT to CONFIG_SPL_DM_RESET, so can use
CONFIG_IS_ENABLED(DM_RESET) checking in reset.h later.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ARCH_MX6 has default values for SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
and SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR.
Do the same for ARCH_MX7 so that users may have a consistent
experience through the i.MX families.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
