Commit graph

1051 commits

Author SHA1 Message Date
Tom Rini
cb4c833b74 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-10-15 08:43:38 -04:00
Stefan Agner
e24bb2b732 mtd: nand: vf610_nfc: resync with upstream Linux version
This resyncs the driver changes with the Linux version of the
driver. The driver received some feedback in the LKML and got
recently acceppted, the latest version can be found here:
https://lkml.org/lkml/2015/9/2/678

Notable changes are:
- On ECC error, reread OOB and count bit flips in OOB too.
  If flipped bits are below threshold, also return an empty
  OOB buffer.
- Return the amount of bit flips in vf610_nfc_read_page.
- Use endianness aware vf610_nfc_read to read ECC status.
- Do not enable IDLE IRQ (since we do not operate with an
  interrupt service routine).
- Use type safe struct for buffer variants (vf610_nfc_alt_buf).
- Renamed variables in struct vf610_nfc (column and page_sz)
  to reflect better what they really representing.

The U-Boot version currently does not support RAW NAND write
when using the HW ECC engine.

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-10-15 11:10:44 +02:00
Ezequiel García
d1d0167663 nand: omap_gpmc: Change correctable bit-flips messages to debug()
Messages on corrected bit-flips are not really useful,
as bit-flips are perfectly normal. Let's avoid cluttering
the console and make them debug.

Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
2015-10-11 17:12:13 -04:00
Yao Yuan
f2b76c6037 mtd: sf: Add support AT26DF081A chip
AT26DF081A is the spi flash type of TWR-MEM(SCH-26248) card.
We can access the flash through DSPI2 on LS1021ATWR board.

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-10-11 16:43:06 +05:30
Hans de Goede
31c5614af4 sunxi_nand_spl: Be smarter about where to look for backup u-boot.bin
We know when u-boot is written to its own partition, in this case the
layout always is:

eb 0 spl
eb 1 spl-backup
eb 2 u-boot
eb 3 u-boot-backup

eb: erase-block

So if we cannot load u-boot from its primary offset we know exactly where
to look for it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-09-29 11:50:07 +02:00
Peng Fan
168617c9b5 mtd: nand: mxs check maximum ecc that platfrom supports
Check maximum ecc strength for each platfrom to avoid the calculated ecc
exceed the limitation.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Han Xu <b45815@freescale.com>
Tested-By: Tim Harvey <tharvey at gateworks.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-20 09:59:54 +02:00
Stefan Roese
62c390f8a3 mtd: nand: fsmc: Fixes and cleanup for fsmc_nand_switch_ecc()
This patch addresses some comments raised by Scott in the last versions.
Here the changes in detail:

- Removed __maybe_unused as its not needed
- Added check for strength == 4 and error out for the unsupported
  ECC strength values
- Don't set .caclulate, .correct, and .bytes for NAND_ECC_SOFT_BCH as this
  will be done in nand_scan_tail()
- Set .caclulate back to fsmc_read_hwecc() in the HW case
- Added comment that this function will only be called on SPEAr platforms,
  not supporting the BCH8 HW ECC (FSMC_VER8)

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-09-15 15:05:21 -04:00
Heiko Schocher
92a3188d7d bitops: introduce BIT() definition
introduce BIT() definition, used in at91_udc gadget
driver.

Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-09-11 17:15:32 -04:00
Simon Glass
cf92e05c01 Move ALLOC_CACHE_ALIGN_BUFFER() to the new memalign.h header
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 17:15:20 -04:00
Simon Glass
6e295186c7 Move malloc_cache_aligned() to its own header
At present malloc.h is included everywhere since it recently was added to
common.h in this commit:

   4519668 mtd/nand/ubi: assortment of alignment fixes

This seems wasteful and unnecessary. We have been trying to trim down
common.h and put separate functions into separate header files and that
change goes in the opposite direction.

Move malloc_cache_aligned() to a new header so that this can be avoided.
The header would perhaps be better named as alignmem.h but it needs to be
included after common.h and people might be confused by this. With the name
memalign.h it fits nicely after malloc() in most cases.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2015-09-11 17:15:16 -04:00
Stefan Roese
1a103c6caa mtd: nand: fsmc: Add BCH4 SW ECC support for SPEAr600
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC strength.
The SPEAr600 HW ECC only supports 1-bit ECC strength.

To enable SW BCH4, you need to specify this in your config header:

#define CONFIG_NAND_ECC_BCH
#define CONFIG_BCH

And use the command "nandecc bch4" to select this ECC scheme upon runtime.

Tested on SPEAr600 x600 board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
2015-09-11 17:15:13 -04:00
Simon Glass
0abdd9d01a arm: Remove nhk8815 boards and nomadik arch
These boards have not been converted to generic board by the deadline.
Remove them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 14:56:04 -04:00
Stefan Roese
cc19722f04 sunxi_nand_spl: Add config parameter for 4KiB page sized NAND devices
This patch adds support for NAND chips with 4KiB page size and 24/1024
ECC strength. Like the Micron MT29F32G08CBACAWP which is used on the
ICnova-A20 SoM.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-09-10 20:20:45 +02:00
Hans de Goede
d90ba790d8 mtd: nand: Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig
Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig, just like
SYS_NAND_BUSWIDTH_16BIT this is only enabled on some SoCs using depends,
to avoid double defining it for SoCs which have not yet moved to Kconfig
for this.

Having this in Kconfig is useful because this is something which may
differ from one board to the other even when using the same SoC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-08-31 08:43:42 +02:00
Boris Brezillon
ddd37fe865 sunxi_nand_spl: clear status flags in SPL implementation
Some status flags remain set until you explicetly clear the bit
in the status register.
Fix the SPL implementation to avoid false positive.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[hdegoede@redhat.com: Port from v2015.07 to v2015.10]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-31 08:43:42 +02:00
Hans de Goede
6a08d65acc sunxi_nand_spl: Remove NAND_SUNXI_SPL_SYNDROME_PARTITIONS_END
We only ever use syndrome mode for the partitions which contain the SPL,
as that is required for the BROM to be able to read the SPL.

Instead of using some arbritray limit for deciding whether or not to
use syndrome, be smart and check if u-boot-dtb.bin is directly behind
the SPL, if it is not then it is on its own partition and we should not
use syndrome.

Note the reason why we only use syndrome mode for the SPL is because it
comeswith weaker randomization, introducing a risk for more bit errors,
so we want to avoid it when possible.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
e526861687 sunxi_nand_spl: Rename SPL_NAND_SUNXI to NAND_SUNXI
We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.

Renaming the Kconfig option now makes things easier when we add full
nand support in the future.

The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
24a06c964f sunxi_nand_spl: Add support for backup boot partitions
The BROM does not care / use bad page markings, instead it deals with
any bad pages in the first erase-block by simply trying to load "boot0"
from the next erase-block.

This commit implements the same strategy for the sunxi spl nand code,
allowing it to boot from the backup boot partition when the main boot
partition is bad (tested by erasing the main boot partition).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
2b8a01a99d sunxi_nand_spl: Auto detect nand configuration parameters
Auto detect the nand configuration parameters, like the BROM does.

This allows us to get rid of various Kconfig settings, and is
necessary to support generic boards like the mk802 which have seen
many production runs with different nands.

The full blown u-boot/kernel nand driver uses the nand id to determine
this info, for the SPL we do as the BROM does and simply try a few
standard configs.

Note the table only contains configs which are known to actually be used,
rather then all the configs the BROM tries. This means that it may need
to be updated in the future as we add support for nand on more boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
f5916d1856 sunxi_nand_spl: Parametrize lowlevel read functions
Parametrize the lowlevel nand_read_page function, instead of directly
using the CONFIG_foo settings for page-size, etc. there and add a few
wrappers / helper functions for calling it.

This is a preparation patch for adding auto-detecting of the nand
parameters like the BROM does.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
0a247554c2 sunxi_nand_spl: Properly config page-size in the nand ctl register
Properly config page-size in the nand ctl register, it seems that things
work fine without doing this, but still lets play it safe and properly
set the page-size.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
022a99d8b2 sunxi_nand_spl: Add support for sun4i and sun5i SoCs
Other then having a few less chip-select lines the nand controller
on sun4i, sun5i and sun7i is identical.

Note this patch also muxes GPC7 to the NAND on sun7i where as before
it was not muxed this way. GPC7 is a standard NAND pin, so it should
always be muxed to the NAND when in use.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:42 +02:00
Hans de Goede
008ac1dfe0 sunxi_nand_spl: Use kernel driver algorithm for determining ecc_mode / _off
Sync the code for figuring out the ecc_mode and ecc_offset with the linux
kernel v4.1. Keeping this in sync seems like a good idea in general, and
it fixes / adds support for ecc strengths of 56, 60 and 64 bits.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
2a43973f64 sunxi_nand_spl: Add proper cache flusing
We are using dma, so we should flush the cache before starting the dma,
and invalidate it once the dma is done.

Things are working without this by mostly luck, but lets not rely on that.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
5d65c67bf1 sunxi_nand_spl: Turn off clocks when we're done with the nand
Turn off the nand and dma clocks when we're done with the nand, this
puts the nand and dma controllers back into a clean state for when the
kernel boots.

Without this the kernel will not boot properly when it is built with
dma-controller support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
f62bfa56da sunxi_nand_spl: Use SYS_NAND_SELF_INIT and only do nand init when necessary
Use SYS_NAND_SELF_INIT and only setup the pinmux and clocks when we are
actually using the nand.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
9da5fca55c sunxi_nand_spl: Do not bother writing the spare-area reg in syndrome mode
In syndrome mode we set the NFC_SEQ bit in the command register, so the
spare-area register is not used. Also the value currently being written is
actual wrong, the ecc sits at "column + CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE"
not just CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE.

So the current code only serves to confuse the user -> remove it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
630cf2e762 sunxi_nand_spl: We only need to reset the nand chip once
There is no need to reset the nand chip for every ecc-block read.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Hans de Goede
10d069b797 sunxi_nand_spl: Drop unnecessary temp buf
nand_spl_load_image() always gets called with either CONFIG_SYS_TEXT_BASE
or spl_image.load_addr as destination, both of which are properly aligened,
and have plenty of space for "overshooting" up to
CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE bytes, as we read in
CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE bytes chunks.

This saves CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE (typically 1k) in
SPL size, which is a lot on the total 24k we have.

Note this changes the dma destination from SRAM to DRAM, so this patch
updates the DDMA_DST_TYPE bits in the dma controller cfg0 reg accordingly.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-31 08:43:41 +02:00
Masahiro Yamada
2bc1f2b592 mtd: denali_spl: do not allocate page_buffer in .bss section
Since commit 2580a2a7e7 ("mtd: nand: Increase max sizes of OOB and
Page size"), three boards (ph1_ld4, ph1_pro4, ph1_sld8) fail to build
with the following error message:
  arm-linux-gnueabi-ld.bfd: SPL image plus BSS too big

They compile drivers/mtd/nand/denali_spl.c and it has a page_buffer
as static data:

    static uint8_t page_buffer[NAND_MAX_PAGESIZE];

This buffer required 8KB in .bss section before that commit and now
it has been increased to 16KB.  Given limited code/memory size for SPL,
it is not a good idea to allocate a page buffer statically.  In the
first place, the load address 'dst' can be used as a page buffer.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-08-30 22:18:00 +09:00
Marcel Ziswiler
4519668b29 mtd/nand/ubi: assortment of alignment fixes
Various U-Boot adoptions/extensions to MTD/NAND/UBI did not take buffer
alignment into account which led to failures of the following form:

ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
[trini: Add __UBOOT__ hunk to lib/zlib/zutil.c due to malloc.h in common.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:17 -04:00
Peng Fan
ecfb8768b1 mtd: nand: mxs invalidate dcache before DMA read
Follow linux dma flow:
Before DMA read, be sure to invalidate the cache over the address
range of DMA buffer to prevent cache coherency problems.
After DMA read, invalidate dcache again.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
2015-08-25 22:53:59 -05:00
Peng Fan
63b29d8082 mtd: nand: mxs support oobsize bigger than 512
If ecc chunk data size is 512 and oobsize is bigger than 512, there is
a chance that block_mark_bit_offset conflicts with bch ecc area.

The following graph is modified from kernel gpmi-nand.c driver with
each data block 512 bytes. We can see that Block Mark conflicts with
ecc area from bch view. We can enlarge the ecc chunk size to avoid
this problem to those oobsize which is larger than 512.

   |                          P                                        |
   |<----------------------------------------------------------------->|
   |                                                                   |
   |                                                (Block Mark)       |
   |                      P'                             |           | |   |
   |<--------------------------------------------------->|     D     | | O'|
   |                                                     |<--------->| |<->|
   V                                                     V           V V   V
   +---+--------------+-+--------------+-+--------------+-+----------+-+---+
   | M |   data       |E|   data       |E|   data       |E|   data   |E|   |
   +---+--------------+-+--------------+-+--------------+-+----------+-+---+
                                                        ^                  ^
                                                        |         O        |
                                                        |<---------------->|

       P : the page size for BCH module.
       E : The ECC strength.
       G : the length of Galois Field.
       N : The chunk count of per page.
       M : the metasize of per page.
       C : the ecc chunk size, aka the "data" above.
       P': the nand chip's page size.
       O : the nand chip's oob size.
       O': the free oob.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
2015-08-25 22:53:58 -05:00
Stefan Roese
873960c89e mtd: nand: Add mvebu (PXA / AXP / A38x) NAND device driver
Cloned from the Linux driver v4.2.0-rc2. Plus some patches from
Antoine Tenart enabling controller initialization and ONFI timing
support:

http://lists.infradead.org/pipermail/linux-mtd/2015-July/060197.html

Please note that this driver needs the Linux NAND subsystem sync to v4.1
from Scott to be applied:

https://www.mail-archive.com/u-boot@lists.denx.de/msg175762.html

Otherwise it will not compile.

Tested on the Marvell Armada XP DB-MV784MP-GP eval board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Ezeguil Garcia <ezequiel.garcia@free-electrons.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
2015-08-25 22:53:58 -05:00
Scott Wood
d3963721d9 nand: Sync with Linux v4.1
Update the NAND code to match Linux v4.1.  The previous sync was
from Linux v3.15 in commit 4e67c57125.

CONFIG_SYS_NAND_RESET_CNT is removed, as the upstream Linux code now
has its own timeout.  Plus, CONFIG_SYS_NAND_RESET_CNT was undocumented
and not selected by any board.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-08-25 22:53:57 -05:00
Ezequiel Garcia
86a720aafc mtd: Introduce mtd_block_isreserved()
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().

While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[scottwood: Cherry-picked from Linux 8471bb73ba10ed67]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-08-25 22:53:57 -05:00
Scott Wood
273310644f nand: Remove __UBOOT__ ifdefs
I didn't approve the patch that added them.  Get them out of the way
before doing a sync.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-08-25 22:53:57 -05:00
Masahiro Yamada
0f9258228e of: clean up OF_CONTROL ifdef conditionals
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL.  We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:

 #ifdef CONFIG_OF_CONTROL
 # if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
 #  define OF_CONTROL 0
 # else
 #  define OF_CONTROL 1
 # endif
 #else
 # define OF_CONTROL 0
 #endif

Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute.  It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.

Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-18 13:46:05 -04:00
Sylvain Lemieux
30cb3bf4a9 nand: lpc32xx: add ECC layout for small page NAND
Incorporate ECC layout for small page NAND from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (ECC layout for small page)

This layout is matching the lpc32xx NAND SLC Linux Kernel driver.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-18 13:45:56 -04:00
Sylvain Lemieux
5f63bf3ec8 nand: lpc32xx: add hardware ECC support
Incorporate NAND SLC hardware ECC support from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (hardware ECC support)
- lpc3250 header file missing SLC NAND registers definition

The legacy driver was updated and clean-up as part of the integration with the existing NAND SLC driver.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
2015-08-18 13:45:56 -04:00
Tom Rini
146bad9619 sf: ops: Add spi_flash_copy_mmap function
When doing a memory mapped copy we may have DMA available and thus need
to have this copy abstracted so that the driver can do it, rather than a
simple memcpy.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-17 23:29:14 +05:30
Marek Vasut
0a02655481 sf: Make 4K sector support configurable
Make the support for 4K subpage I/O on a SPI NOR flash configurable.
A board which requires the SPI NOR to be accessed in larger 32KiB
or 64KiB pages can disable the 4K subpage support, but by default,
the support for 4K subpage I/O is enabled. The functionality of this
option is the same as CONFIG_MTD_SPI_NOR_USE_4K_SECTORS in Linux.

This is extremely useful in case one uses UBI on a SPI NOR flash.
UBI needs at least 15k EBs and can not work on a flash which uses
4k ones, so disabling the support for 4k subpages lets UBI work on
such flash.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-17 15:59:48 +05:30
Marcel Ziswiler
6eeedc196d tegra: nand: disable subpage writes
Disable subpage writes as we do not provide ecc->hwctl.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-13 13:06:03 -07:00
Marcel Ziswiler
adf4800d85 mtd/nand/tegra: alignment workaround
Integrate cache alignment bounce buffer to workaround issues as follows:

Loading file '/boot/zImage' to addr 0x01000000 with size 4499152 (0x0044a6d0)...
ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108
Done
Kernel image @ 0x1000000 [ 0x000000 - 0x44a6d0 ]

Starting kernel ...

undefined instruction
pc : [<005ff03c>]          lr : [<0000800c>]
sp : 0144b6e8  ip : 01000188     fp : 0144a6c8
r10: 00000000  r9 : 411fc090     r8 : 00000100
r7 : 00000cfb  r6 : 0144a6d0     r5 : 00000000  r4 : 00008000
r3 : 0000000c  r2 : 00000100     r1 : 00000cfb  r0 : 00000000
Flags: nZCv  IRQs off  FIQs off  Mode SVC_32
Resetting CPU ...

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-13 13:06:02 -07:00
Marcel Ziswiler
1bc66a57c0 tegra: nand: fix read_byte required for proper onfi detection
Fix PIO read_byte() implementation not only used for the legacy READ ID
but also the PARAM command required for proper ONFI detection.

This fix is inspired by Lucas Stach's Linux Tegra NAND driver of late
(not mainline yet but getting there soon I hope).

I vaguely remember that those commands are special on 16-bit bus NAND
(e.g. always return 8-bit data regardless) and later Linux MTD fixed/
changed the way this is handled which in turn broke once U-Boot pulled
that in. Basically instead of doing PIO read regular DMA block read is
now used which this patch actually fixes.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-13 13:06:02 -07:00
Vladimir Zapolskiy
dcfd37e5ef nand: lpc32xx: add SLC NAND controller support
The change adds support of LPC32xx SLC NAND controller.

LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.

This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.

Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.

The driver can be included to an SPL image.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
2015-08-12 20:47:33 -04:00
Vladimir Zapolskiy
8d1809a966 spl: nand: simple: replace readb() with chip specific read_buf()
Some NAND controllers define custom functions to read data out,
respect this in order to correctly support bad block handling in
simple SPL NAND framework.

NAND controller specific read_buf() is used even to read 1 byte in
case of connected 8-bit NAND device, it turns out that read_byte()
may become outdated.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-08-12 20:47:33 -04:00
Heiko Schocher
c10ac540ea nand, atmel: remove udelay in spl_nand_erase_one()
remove unneeded udelay() in this function, as we use
the dev_ready pin.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-08-12 20:47:27 -04:00
Piotr Zierhoffer
960caeba8f sunxi: nand: Add board configuration options
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.

This commit also introduces the configurable options in Kconfig.

Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-08 16:26:19 +02:00
Piotr Zierhoffer
aeb4b0d3b3 sunxi: nand: Add basic sunxi NAND driver for SPL with DMA support
This driver adds NAND support to SPL.
It was tested on Allwinner A20.

Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-08 16:26:19 +02:00