This patch adds support of SD3.0 for ZynqMP.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reads the capabilities register1 and update the host
caps accordingly for mmc layer usage. This patch mainly reads
for UHS capabilities inorder to support SD3.0.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to invoke any platform specific tuning
and delay routines if available.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new hooks for any platform specific tuning and
tap delays programing. These are needed for supporting
SD3.0.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to disable clock if clk_disable
was set and then enable or set clock if the clock was changed
or clock was disabled when clock needs to be enabled.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changed the datatype of variable "start" from uint to ulong
to work properly on 64-bit machines as well. Also the return type of
get_timer() function is ulong.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.
This configuration with uart1 was tested on zcu100-revC.
U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)
Model: Xilinx ZynqMP R5
DRAM: 512 MiB
WARNING: Caches not enabled
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: Net Initialization Skipped
No ethernet found.
ZynqMP r5>
There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split
2. Load via jtag when directly to R5
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The officially described way to generate boot.bin files for ZynqMP is to
describe the contents of the target binary using a file of the "bif"
format. This file then links to other files that all get packed into a
bootable image.
This patch adds support to read such a .bif file and generate a respective
ZynqMP boot.bin file that can include the normal image and pmu files, but
also supports image partitions now. This makes it a handy replacement for
the proprietary "bootgen" utility that is currently used to generate
boot.bin files with FSBL.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynqmpimage.c and the new zynqmpbif.c files are all maintained by
Xilinx for the Zynq platforms. Let's match them accordingly
in the MAINTAINERS file.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We will add support for ZynqMP bif input files later, so let's move
all structure definitions into a header file that can be used by that
one as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynqmp image format has support for inline partitions which are
used by FSBL to describe payloads that are loaded by FSBL itself.
While we can't create images that contain partitions (yet), we should
still at least be able to examine them and show the user what's inside
when we analyze an image created by bootgen.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DISPLAY_BOARDINFO in OF case show model identification string from DT.
Enable this feature instead of custom IDENT_STRING which does the same
thing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Call calloc for space allocation only at one location and include if/else
to sprintf. This will simplify run time device adding based on id aliases.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
This patch fills the MMU map for DDR at run time based on information read
from Device Tree or automatically detected from static configuration.
The patch is needed because for systems which has for example 1GB of memory
but MMU map is 2GB there could be spurious accesses which was seen in past
when mapping is not fitting with actual memory installed.
Signed-off-by: Nitin Jain <nitin.jain@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable watchdog on zcu100 to make sure if there is a bug in the u-boot
there is proper reset.
Watchdog expires and PMU fw is informed and based on setting proper
action is taken.
The patch is enabling reset-on-timeout feature and also fixing fixed
clock rate for watchdog where 100MHz is max (and also default) clock value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable watchdog in full U-Boot.
Similar changes were done by:
"arm: zynq: Wire watchdog internals"
(sha1: e6cc3b25d7)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Debug message was showing timeout value which was passed to start
function but there is a checking if this value can be setup.
The patch is moving this debug printf function below checking.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Send address cycles as per value read from onfi parameter
page for Read and write commands instead of using a
hard coded value. This may vary for different parts and
hence use it from onfi parameter page value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for 16-bit buswidth by determining
the bus width based on mio configuration.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes UBI support from defconfig and it can
be enabled from menuconfig as per need.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables support zc1275 revB board. It has
SD added compared to revA. The same configuration will
work for RevC boards aswell.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In v2018 the patch
"dm: ahci: Correct uclass private data"
(sha1: bfc1c6b483)
was causing an issue for ceva_sata.
But this issue is not in v2018.05-rc1 but still converting to
UCLASS_AHCI would make more sense.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now that showing silicon version is part of the CPU
info display, let's remove checkboard().
Note that the generic show_board_info() will still
show the DT 'model' property. For instance:
U-Boot 2018.05-rc2-00025-g611b3ee0159b (Apr 19 2018 - 11:23:12 +0200)
CPU: Zynq 7z045
Silicon: v1.0
Model: Zynq ZC706 Development Board
I2C: ready
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>,
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
mini configuration doesn't need to show this information.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit moves the FPGA descriptor definition
to mach-zynq, where it makes more sense.
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In past this code was commented and was used for debug purpose.
But there is no reason not to enabled it based on macros.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.
Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Avoid creating incorrect comments like /* ...*/... */ by printing
'.' instead of '*' inside comments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Without the patch gcc 8 produces:
warning: ignoring attribute ‘noreturn’ because it conflicts with
attribute ‘const’ [-Wattributes]
int ____ilog2_NaN(void);
So let's update the include from Linux kernel v4.16.
This removes static checks of ilog2() arguments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Every va_start() call must be matched by a va_end() call.
scripts/checkpatch.pl required reformatting the complete function
zm_dprintf().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
file2include is used to convert a binary file to a C include.
With the patch the SPDX header is written to the first line as
expected by scripts/checkpatch.pl.
Cf. https://www.kernel.org/doc/html/v4.16/process/license-rules.html
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The check for having a memory node within the fdt blob is made wrong, we
fix this here.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Attempting to build with both DEBUG and CONFIG_USE_TINY_PRINTF along
with CONFIG_SPL_YMODEM_SUPPORT fails at link time:
common/built-in.o: In function `zm_dprintf':
common/xyzModem.c:190: undefined reference to `vsprintf'
Disable Ymodem debug if we don't have full vsprintf support.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
These fsl email addresses are no longer valid and they do not have a
correspondent nxp.com entry.
Remove all invalid fsl email addresses and mark the boards as orphan.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
timur@freescale.com is not a valid email for quite some time, so change
it to Timur's updated email.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Timur Tabi <timur@tabi.org>
This patch is necessary for providing basic bootcount checking in the case
of using "falcon" boot mode in that board.
It forces u-boot proper boot, when we exceed the number of errors.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds support for incrementation of the bootcount in SPL.
Such feature is necessary when we do want to use this feature with
'falcon' boot mode (which loads OS directly in SPL).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The code has been refactored to use common wrappers from bootcount.h
header.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Those two functions can be used to provide easy bootcount management.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds missing include guards for bootcount.h file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
New, SPL related config option - CONFIG_SPL_BOOTCOUNT_LIMIT has been
added to allow drivers/bootcount code re-usage in SPL.
This code is necessary to use and setup bootcount in SPL in the case of
falcon boot mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Allow optionally bringing up the Apalis type specific 4 lane PCIe port
as well as the PCIe switch as found on the Apalis Evaluation board. In
order to avoid violating the PCIe reset timing do this by overriding the
tegra_pcie_board_port_reset() function. Note however that both the
Apalis type specific 4 lane PCIe port as well as the regular Apalis PCIe
port are also left disabled in the device tree by default.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix optional Apalis type specific 4 lane PCIe port 0 and Apalis PCIe
port 1 pin muxing.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add some more comments describing the various PCIe ports available.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
