It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Align USB nodes with the latest dt-bindings. It is adding resets, new
interrupt and also some quirks.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc supports new sugar syntax which is easier compare to previous one
that's why also covert overlays for SOM to it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
kv260-revB is different compare to revA (usbhub is wired via i2c) that's
why remove revA compatible string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Clocking Wizard IP supports clock circuits customized
to your clocking requirements. The wizard support for
dynamically reconfiguring the clocking primitives for
Multiply, Divide, Phase Shift/Offset, or Duty Cycle.
Limited by U-Boot clk uclass without set_phase API, this
patch only provides set_rate to modify the frequency.
Signed-off-by: Zhengxun <zhengxunli.mxic@gmail.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx ZynqMP supports also addresses above 4GB (32bit) that's why also
generate u-boot.its with 64bit load/entry addresses to also support
different configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clock setting is not static anymore that's why it depends on firmware setup
that's why remove this comment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Networking subsystem is not using aliases that's why remove them for CAN
devices. There is also no any other Xilinx ZynqMP DT file with them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As per the design specification
"The 16-bit Seconds Calibration Value represents the number of
Oscillator Ticks that are required to measure the largest time
period that is less than or equal to 1 second.
For an oscillator that is 32.768 KHz, this value will be 0x7FFF."
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Historically dpdma and dpsub are placed at the end of files. Move nodes
there for easier comparison among dts files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dwc3 can be used only for higher speeds than super-speed that's why
explicitly set it up.
This is also aligned with other ZynqMP dts files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Uarts already have u-boot,dm-pre-reloc via zynqmp.dtsi that's why there is
no need to have them in platform DT files too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is need to pass entry about secure OS when bl32_entry is defined.
Currently only 64bit support is added but /fit-images node have been
extended to also record if this is 32bit or 64bit secure OS. When this is
tested the code will be update to support this configuration too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The first change is to trying to find out TF-A load address based on
reading elf file. Expectation is that bl31.bin is in the same folder as
bl31.elf. It brings new flexibility to place TF-A to any address (DDR
included).
And also enable TEE generation also with TEE configuration.
Expecation is the same as above that tee.bin and tee.elf are in the same
folder.
User has to just define link to BL31/BL32 binary files and the rest should
be handled by the script.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
TF-A and SecureOS can allocate the part of DDR for self but U-Boot is not
handling this configuration that the part of memory is reserved and
shouldn't be used by U-Boot. That's why read all reserved memory locations
and don't use it.
The code was taken from commit 4a1b975dac ("board: stm32mp1: reserve
memory for OP-TEE in device tree") and commit 1419e5b516 ("stm32mp:
update MMU config before the relocation") which is used by stm32 and does
the job properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SMMU is disabled in device tree so this change has no impact.
The benefit is that this way it is in sync with xen.dtsi. Xen enables
the SMMU and makes use of it.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
There is no reason to have CCI no enabled by default. Enable it when your
system configuration requires it. In Xilinx configuration flow this is
work for Device Tree Generator which reads information from HW Design
configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
K26 has EMMC and SD and default 0 is not working when system is booting out
of SD which is controller 1. Add controller autodetection via
mmc_get_env_dev(). The same code is used for distro_boot selection done in
board_late_init(). bootseq variable can't be reused because this is called
so late.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Rename amba to AXI. Based on Xilinx Zynq TRM (Chapter 5) chip is "AXI
point-to-point channels for communicating addresses, data, and response
transactions between master and slave clients. This ARM AMBA 3.0..."
Issues are reported as:
.. amba: $nodename:0: 'amba' does not match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
>From schema:
../github.com/devicetree-org/dt-schema/dtschema/schemas/simple-bus.yaml
Similar change has been done for Xilinx ZynqMP SoC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/8a4bc80debfbb79c296e76fc1e4c173e62657286.1606397101.git.michal.simek@xilinx.com
SVDs are using different name which can't be handled via zynqmp_devices
structure. That's why introduce zynqmp_detect_svd_name() which checks ID
code for these devices and show proper name for them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enabling EFI secure boot which is required for EBBR specification.
Enabling this will fix
"RT.SetVariable - Create one Time Base Auth Variable, the expect return
status should be EFI_SUCCESS"
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
From U-Boot, loading application on RPU core 0 is fine but loading on
core 1 is not handled properly. Lock-step mode needs both the R5 cores
to be initialized and it is working fine. Whereas in SPLIT mode individual
R5 cores needs to be initialized as they need to execute differenet
applications. Handle both these lock-step and split modes by propagating
mode and RPU core number(4 for RPU0 and 5 for RPU1) for various functions
and by adding conditions in those functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Linux commit f69629919942 ("dt-bindings: sram: Convert SRAM bindings to
json-schema") converted binding to yaml and some missing required
properties started to be reported. Align binding based on it.
The patch is fixing these warnings:
.../zynq-zc702.dt.yaml: sram@fffc0000: '#address-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: '#size-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: 'ranges' is a required property
>From schema: .../Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/87c02786ccd8d7827827a9d95a8737bb300caeb0.1606397101.git.michal.simek@xilinx.com
The Linux commit f8f79fa6bb25 ("dt-bindings: at25: convert the binding
document to yaml") converted binding to yaml and 3 deprecated properties
pop up.
The patch is fixing these warnings:
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'pagesize' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'size' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'address-width' is a required property
>From schema: .../Documentation/devicetree/bindings/eeprom/at25.yaml
by converting them to new binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/be2c1125d98386033e182012eb08986924707a76.1606397101.git.michal.simek@xilinx.com
Use the ZDMA channel 0 to initialize the DRAM banks. This avoid
spurious ECC errors that can occur when accessing unitialized memory.
The feature is enabled by setting the option
CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT and providing the following data:
SPL_ZYNQMP_DRAM_BANK1_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK1_LEN : len of memory to initialize (hex)
SPL_ZYNQMP_DRAM_BANK2_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK2_LEN : len of memory to initialize (hex)
Setting SPL_ZYNQMP_DRAM_BANK_LEN to 0 takes no action.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
pca953x also depends on i2c that's why add dependency to Kconfig.
Where GPIO is enabled but I2C compilation error pops up.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Replace typo CONFIG_USE_AUTOBOOT_MENUKEY with
CONFIG_AUTOBOOT_USE_MENUKEY as when they were introduced initially there
was some mismatch in which name was used where.
Fixes: 8fc31e23aa ("autoboot: Rename CONFIG_MENUKEY to CONFIG_AUTOBOOT_MENUKEY")
Signed-off-by: Da Xue <da@libre.computer>
This function is passed *dev not *dev_desc, so pass the right name to
part_init().
Fixes: f14c5ee5ab ("disk: part_dos: update partition table entries after write")
Signed-off-by: Christian Melki <christian.melki@t2data.com>
MSYS2 Windows build started to fail since yesterday (Jun 21):
checking keyring...
checking package integrity...
error: gcc-libs: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust
:: File /var/cache/pacman/pkg/gcc-libs-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)).
error: gcc: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust
:: File /var/cache/pacman/pkg/gcc-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)).
error: failed to commit transaction (invalid or corrupted package)
Errors occurred, no packages were upgraded.
Switching to the latest installer (version 20210604) seems to fix it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com>
The MX66UW2G345G is Macronix Flash with SINGLE and OCTAL I/O. Hence,
add SPI_NOR_OCTAL_READ flag for this flash.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: change order of id flags]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: zhengxun <zhengxunli.mxic@gmail.com>
This reverts commit 63756575b4.
Since this commit a imx6qdl-pico board boots extremely slowly
in both SPL as well as U-Boot proper.
Fix this regression by reverting the offending commit for now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com>
