Francesco Dolcini <francesco.dolcini@toradex.com> says:
This series fixes two regressions affecting multiple Toradex boards
(i.MX, TI and TEGRA based) and targets the current master, e.g. v2024.04
release.
U-Boot `reset` command is broken on all Tordex i.MX6* based SoMs since
v2023.07, this series fixes it enabling the `wdt-reboot` driver.
Since v2024.04-rc1 reading the Toradex configuration block is not working
properly anymore, the serial number and the hardware version are not read
correctly, preventing the board from functioning correctly (wrong mac address,
wrong DT, ...). This is fixed by reading the config block in `EVT_SETTINGS_R`
and adding a toradex sysinfo driver. In addition to that, we now use a random
mac address in case the config block is invalid.
Reported-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Closes: https://lore.kernel.org/all/CAKZ1LvM45MB8N0CqgU+C7i9=Bjb6kqNTxWo2Tv407HKLWtCMkA@mail.gmail.com/
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Closes: https://lore.kernel.org/all/e40ed93bd8f371ec56b8fc451dcb458f3ce6dcba.camel@toradex.com/
Reported-by: Francesco Dolcini <francesco@dolcini.it>
Closes: https://lore.kernel.org/all/ZY2ZDWAQuTlRjV9H@francesco-nb/
Set CONFIG_NET_RANDOM_ETHADDR=y, which sets random eth address in
case there is no toradex config block programmed.
In case of missing toradex config block the generated mac address was
always the same, linked to serial number 0.
Use random generated mac address instead.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin iMX8M Plus
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Disable CONFIG_SPL_LOAD_FIT_APPLY_OVERLAY, this is not required nor used
on verdin am62, disable it to save precious binary size.
Update defconfig using savedefconfig, this adds CONFIG_OF_LIBFDT_OVERLAY
explicitly.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This adds initial support for the Toradex Verdin AM62 Quad 1GB WB IT
V1.0A module and subsequent V1.1 launch configuration SKUs. They are
strapped to boot from their on-module eMMC. U-Boot supports booting
from the on-module eMMC only, DFU support is disabled for now due to
missing AM62x USB support.
The device trees were taken straight from Linux v6.5-rc1.
Boot sequence is:
SYSFW ---> R5 SPL (both in tiboot3.bin) ---> ATF (TF-A) ---> OP-TEE
---> A53 SPL (part of tispl.bin) ---> U-boot proper (u-boot.img)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Nishanth Menon <nm@ti.com>